VT220 Programmer Reference Manual| Chapter 3 | Contents |
| VT100/VT200 ANSI Mode* |
VT52 Mode* | |||
|---|---|---|---|---|
| Key | Keypad Numeric Mode |
Keypad Application Mode |
Keypad Numeric Mode |
Keypad Application Mode |
| * | ANSI mode applies to VT200 and VT100 modes. VT52 mode is an ANSI-incompatible mode. | |||
| † | You cannot generate these sequences on a VT52 terminal. | |||
| ‡ | Keypad Numeric Mode. ENTER generates the same codes as RETURN. You can change the code generated by RETURN with the Linefeed/New Line Mode. When reset, the Linefeed/New Line Mode causes RETURN to generate a single control character (CR). When set, the mode causes RETURN to generate two control characters (CR, LF). | |||
| 0 | 3/0 0 |
8/15 7/0 SS3 p |
3/0 0 |
1/11 3/15 7/0 ESC ? p |
| 1 | 3/1 1 |
8/15 7/1 SS3 q |
3/1 1 |
1/11 3/15 7/1 ESC ? q |
| 2 | 3/2 2 |
8/15 7/2 SS3 r |
3/2 2 |
1/11 3/15 7/2 ESC ? r |
| 3 | 3/3 3 |
8/15 7/3 SS3 s |
3/3 3 |
1/11 3/15 7/3 ESC ? s |
| 4 | 3/4 4 |
8/15 7/4 SS3 t |
3/4 4 |
1/11 3/15 7/4 ESC ? t |
| 5 | 3/5 5 |
8/15 7/5 SS3 u |
3/5 5 |
1/11 3/15 7/5 ESC ? u |
| 6 | 3/6 6 |
8/15 7/6 SS3 v |
3/6 6 |
1/11 3/15 7/6 ESC ? v |
| 7 | 3/7 7 |
8/15 7/7 SS3 w |
3/7 7 |
1/11 3/15 7/7 ESC ? w |
| 8 | 3/8 8 |
8/15 7/8 SS3 x |
3/8 8 |
1/11 3/15 7/8 ESC ? x |
| 9 | 3/9 9 |
8/15 7/9 SS3 y |
3/9 9 |
1/11 3/15 7/9 ESC ? y |
| - | 2/13 - (minus) |
8/15 6/13 SS3 m |
2/13 - |
1/11 3/15 6/13† ESC ? m |
| , | 2/12 , (comma) |
8/15 6/12 SS3 l |
2/12 , |
1/11 3/15 6/12† ESC ? l |
| . | 2/14 . (period) |
8/15 6/14 SS3 n |
2/14 . |
1/11 3/15 6/14 ESC ? n |
| Enter‡ | 0/13 CR |
8/15 4/13 SS3 M |
0/13 CR |
1/11 3/15 4/13 ESC ? M |
| or | 0/13 0/10 CR LF |
or | 0/13 0/10 CR LF |
|
| PF1 | 8/15 5/0 SS3 P |
8/15 5/0 SS3 P |
1/11 5/0 ESC P |
1/11 5/0 ESC P |
| PF2 | 8/15 5/1 SS3 Q |
8/15 5/1 SS3 Q |
1/11 5/1 ESC Q |
1/11 5/1 ESC Q |
| PF3 | 8/15 5/2 SS3 R |
8/15 5/2 SS3 R |
1/11 5/2 ESC R |
1/11 5/2 ESC R |
| PF4 | 8/15 5/3 SS3 S |
8/15 5/3 SS3 S |
1/11 5/3 ESC S |
1/11 5/3‡ ESC S |