DECndu Plus for DOS 1. Download NDUPLUS.ZIP to your system. 2. Decompress the ZIP file by typing "PKUNZIP NDUPLUS.ZIP". Note that PKUNZIP may also be Downloaded from this BBS. Select the BBS User/System Information area. 3. Help with DECndu Plus can be found by typing "decndup /?" 4. Read READMEDN.TXT found in the ZIP file for more information DECndu Plus for OpenVMS VAX The Saveset provided for OpenVMS VAX should be installed on your system in the normal fashion using VMS Install. The release notes are included in the Saveset. The following help screens are provided here for for your convenience and also can be found once DECndu Plus is installed from the VMS Help Utility using$ help download. DOWNLOAD DECndu (Network Device Upgrade) is used to download a new software image into supported devices. DOWNLOAD LIST will display the devices supported by DECndu. DECndu can also display device information such as type and firmware version. New in DECndu Plus V1.0, DEChub modules implementing SNMP and TFTP protocols can be downline loaded. Additional information available: LIST SHOW LOAD Press RETURN to continue ... LIST DOWNLOAD LIST Displays a list of supported devices that can be updated with DECndu. DOWNLOAD Subtopic? SHOW DOWNLOAD SHOW Additional information available: VERSION DEVICE Displays information about supported device. Use DOWNLOAD LIST to get list of supported devices. Remote Device Format (MAC): DOWNLOAD SHOW DEVICE 08-00-2B-xx-xx-xx /CONTROLLER=esa0 Remote Device Format (IP): DOWNLOAD SHOW DEVICE 16.20.216.143 (MAM or Standalone) Press RETURN to continue ... DOWNLOAD SHOW DEVICE 16.20.216.143 /mod=3 /force=CHASDESCR (900 MODULES) Local Device Format: DOWNLOAD SHOW DEVICE fxa0 Note: fxa0 (DEC_FDDIcontroller400) in this example is a local device wich does not support RBMS protocol. Obtaining device information and upgrades cannot be done remotely. Additional information available: /CONTROLLER Parameters DOWNLOAD SHOW DEVICE Subtopic? DOWNLOAD LOAD Update the specified device with the specified image. Format: DOWNLOAD LOAD target image_file Additional information available: Parameters /PASSWORD /MODULE /READ_COMMUNITY /WRITE_COMMUNITY /RESET /CONTROLLER /LOG /CONFIRM /NOMANAGEMENT Examples: DOWNLOAD LOAD Subtopic? DOWNLOAD LOAD Examples: DOWNLOAD SHOW VERSION Displays the version of the DECndu utility. DOWNLOAD LIST Display list of devices supported by DECndu. DOWNLOAD SHOW DEVICE 08-00-2b-14-14-1c Will send a RBMS show device request if MAC address used. DOWNLOAD SHOW DEVICE 16.21.16.21 will bring back a description of the device. DOWNLOAD SHOW DEVICE /FORCE=CHASDESCR /MODULE=5 16.20.217.130 Will send an SNMP get chasSlotModuleDescr. This will send back a description of module 5. The IP address should be that of a hub. DOWNLOAD SHOW DEVICE /FORCE=GIGADESCR /MODULE=7 16.20.36.100 Will show Gigaswitch module 7 status, type, hardware rev, and software rev. DOWNLOAD LOAD 08-00-2B-14-14-1C FIRMWARE$PATH:defcn220.sys Updates a device which supports RBMS and MOP protocols because MAC address specified as target. DOWNLOAD LOAD /LOG /CONFIRM /PASS="defebpass" - 08-00-2B-14-14-1C FIRMWARE$PATH:defcn220.sys Updates a remote device with a password; verifies and displays informational messages. DOWNLOAD LOAD /FORCE=PCOMMON 16.21.16.21 FIRMWARE$PATH:nirep.bin Updates a stand alone device which supports SNMP and TFTP protocols and supports the DEChub Common MIB. DOWNLOAD LOAD /FORCE=HUBMAMV2 /MODULE=9 16.21.16.22 - FIRMWARE$PATH:mamv2.bin Updates the management module in slot 9 of DEChub 900. DOWNLOAD LOAD /FORCE=HUBMAMV2 /MODULE=9 /PASS="setcommunity" - 16.20.16.13 FIRMWARE$PATH:mamv2.bin Updates the DEChub 900 Management Module with community string other than public. DOWNLOAD LOAD /FORCE="HUBMODULE" /MODULE=5 16.20.16.13 - FIRMWARE$PATH:newfw.bin Updates the DEChub 900 module in slot 5 of the hub. DOWNLOAD LOAD /MODULE=4 /PASS="08002bc00100" - 16.21.37.100 FIRMWARE$PATH:fglop043.rsx Example of a update of an FGL in slot 4 of a Gigaswitch with password "08002bc01000". DECndu Plus for Ultrix TO INSTALL A DECNDU PLUS TAR FILE KIT ON ULTRIX. Create a scratch directory "tmp" and copy the tar file into it. The following command should be used to unpack and install DECndu Plus # tar -xvf nduplus100.tar # setld -l /tmp/ndupbin_output *** Enter Subset Selections *** The subsets listed below are optional: 1) DECndu Plus Base System 2) All of the Above 3) None of the Above 4) Exit without installing subsets Enter your choice(s): 1 You are installing the following subsets: DECndu Plus Base System Is this correct? (y/n): y Copyright (c) Digital Equipment Corporation, 1993. All Rights Reserved. Beginning installation of DECndu Plus V1.0 DECndu Plus Base System (NDUPBIN100) Copying from /tmp/ndupbin_output (disk) Verifying Successful installation of DECndu Plus V1.0 Would you like to run the IVP after the installation? (Y/N) y Beginning DECndup V1.0 IVP Successfully found ./usr/kits/NDUPLUS100/decndup Successfully found ./usr/kits/NDUPLUS100/ndu_msg.cat Successfully found ./usr/kits/NDUPLUS100/ndu_dev.dat Successfully found ./usr/kits/NDUPLUS100/decndu.4 Successfully found ./usr/kits/NDUPLUS100/tftp_server # decndup -V (c) Digital Equipment Corporation. 1993. All Rights Reserved. DECndu Plus V1.0 Successful completion of DECndup V1.0 IVP # rehash # decndup -l /* List of supported devices */ # man decndu /* Man pages shows examples */