____________________________________________________ DECwindows Motif V1.2-3 for OpenVMS Language Variants Installation Guide July 1995 This manual describes the installation procedure for the DECwindows Motif V1.2-3 for OpenVMS Czech, Hungarian, Japanese, Korean, Polish, Russian, Slovak, Thai, Simplified Chinese and Traditional Chinese language variants. Revision/Update Information: This is a new manual. Operating System: OpenVMS Alpha Version 1.5 OpenVMS Version 5.5-2 Software Version: DECwindows Motif Worldwide Support V1.2- 3 for OpenVMS Alpha, DECwindows Motif V1.2-3 for OpenVMS language variants, DECwindows Motif Worldwide Support V1.2- 3 for OpenVMS VAX, and DECwindows Motif V1.2-3 for OpenVMS language variants. Digital Equipment Corporation ________________________________________________________________ July 1995 The information in this document is subject to change without notice and should not be construed as a commitment by Digital Equipment Corporation. Digital Equipment Corporation assumes no responsibility for any errors that may appear in this document. The software described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license. Possession, use, or copying of the software described in this publication is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. © Digital Equipment Corporation 1995. All Rights Reserved. The following are trademarks of Digital Equipment Corporation: Alpha, Bookreader, CDA, DEC, DECfonts, DECimage, DECnet, DECpresent, DECterm, DECwindows, DECwrite, Digital, DTIF, LAT, OpenVMS, ULTRIX, VAX, VAX DOCUMENT, VMS, VT320, VT330, VT340, XUI, and the DIGITAL logo. The following are third-party trademarks: Display PostScript and PostScript are registered trademarks of Adobe Systems Incorporated. Motif and OSF/Motif are registered trademarks of the Open Software Foundation, Inc. POSIX is a registered trademark of the IEEE. UNIX is a registered trademark licensed exclusively by X/Open Company Limited. Windows is a trademark, and Windows NT, NT, and Microsoft are registered trademarks of Microsoft Corporation. X Window System is a trademark of the Massachusetts Institute of Technology. All other trademarks and registered trademarks are the property of their respective holders. This document is available on CD-ROM. This document was prepared using VAX DOCUMENT, Version 2.2. _________________________________________________________________ Contents Preface................................................... vii 1 Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1.1 License Registration.......................... 1-3 1.2 Supported Hardware............................ 1-4 1.3 Required Operating System Software............ 1-4 1.4 OSF/Motif Release 1.1.3 Programming Support and XUI....................................... 1-6 1.5 Saving Customized Bookreader Files............ 1-7 1.6 Product and Device Names...................... 1-8 1.7 Installation Procedure Requirements........... 1-8 1.7.1 Process Privileges........................ 1-9 1.7.2 Process Account Quotas.................... 1-10 1.7.3 Disk Space................................ 1-11 1.7.3.1 Using an Alternate Working Device....... 1-12 1.7.3.2 Using the Distributed File Service...... 1-13 1.7.4 System Parameters......................... 1-14 1.7.5 Additional System Maintenance Procedures................................ 1-15 1.7.5.1 Checking System Parameter Values........ 1-15 1.7.5.2 Calculating the Amount of Free Global Pages and Global Sections .............. 1-16 1.7.5.3 Changing System Parameter Values Using the AUTOGEN Utility..................... 1-17 1.7.6 Backing Up Your System Disk............... 1-19 1.7.7 Notifying Other Users..................... 1-19 iii 2 Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2.1 Installation Procedure........................ 2-2 2.1.1 Invoking VMSINSTAL........................ 2-2 2.1.2 Confirming System Backup.................. 2-4 2.1.3 Mounting Distribution Media............... 2-4 2.1.4 Choosing a Release Notes Option........... 2-5 2.1.5 Continuing the Installation............... 2-6 2.1.6 Preserving the OSF/Motif Release 1.1.3 Programming Environment................... 2-7 2.1.7 Installing the Entire Kit................. 2-7 2.1.8 Choosing Programming Support Files........ 2-8 2.1.9 Verifying Kit Selections.................. 2-9 2.1.10 Verifying Disk Space...................... 2-10 2.1.11 Verifiying License Registration........... 2-12 2.1.12 Performing a System Reboot................ 2-12 2.1.13 Reading Informational Messages............ 2-14 2.1.14 Using AUTOGEN to Set System Parameters.... 2-16 2.1.15 Completing the Installation Procedure..... 2-18 2.2 Recovering from Errors........................ 2-19 2.3 Accessing the Release Notes................... 2-19 3 After Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 3.1 Starting the DECwindows Motif Software........ 3-1 3.1.1 Standalone Systems........................ 3-2 3.1.2 VMScluster Systems........................ 3-3 3.1.2.1 Starting Nonsatellite and Boot Nodes.... 3-3 3.1.2.2 Starting Satellite Nodes................ 3-4 3.2 Running the IVP............................... 3-4 3.3 Choosing an Alternative Console............... 3-6 4 Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4.1 Customizing the DECwindows X11 Display Server Startup Procedure ............................ 4-1 4.2 Using the DECW$MOTIF_TAILOR Utility........... 4-7 4.2.1 Removing DECwindows Motif Files from the System Disk............................... 4-10 4.3 Adding DECwindows Base Support Files.......... 4-14 iv 4.3.1 Using the SYS$UPDATE:DECW$TAILOR.EXE Utility................................... 4-14 4.3.1.1 Adding DECwindows Files to the System Disk.................................... 4-16 4.4 Customizing Font Caching Parameters........... 4-19 5 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5.1 Installation of the Japanese Language Variant....................................... 5-1 5.1.1 License PAK............................... 5-1 5.1.2 Required Software......................... 5-1 5.1.3 Product Name.............................. 5-2 5.1.4 Disk Space Requirement.................... 5-2 5.1.5 System Parameter.......................... 5-2 5.1.6 Installation Verification Procedure....... 5-3 5.2 Installation of the Korean language Variant... 5-3 5.2.1 License PAK............................... 5-3 5.2.2 Required Software......................... 5-3 5.2.3 Product Name.............................. 5-4 5.2.4 Disk Space Requirement.................... 5-4 5.2.5 System Parameter.......................... 5-4 5.2.6 Installation Verification Procedure....... 5-5 5.3 Installation of the Simplified Chinese language Variant.............................. 5-6 5.3.1 License PAK............................... 5-6 5.3.2 Required Software......................... 5-6 5.3.3 Product Name.............................. 5-6 5.3.4 Disk Space Requirement.................... 5-7 5.3.5 System Parameter.......................... 5-7 5.3.6 Production Key Registration (VAX only).... 5-7 5.3.7 Installation Verification Procedure....... 5-8 5.4 Installation of the Thai language Variant..... 5-8 5.4.1 License PAK............................... 5-8 5.4.2 Required Software......................... 5-8 5.4.3 Product Name.............................. 5-9 5.4.4 Disk Space Requirement.................... 5-9 5.4.5 System Parameter.......................... 5-9 5.4.6 Installation Verification Procedure....... 5-10 5.5 Installation of the Traditional Chinese language Variant.............................. 5-11 5.5.1 License PAK............................... 5-11 v 5.5.2 Required Software......................... 5-11 5.5.3 Product Name.............................. 5-11 5.5.4 Disk Space Requirement.................... 5-12 5.5.5 System Parameter.......................... 5-12 5.5.6 Installation Verification Procedure....... 5-12 5.6 Installation of the Czech language variant.... 5-13 5.6.1 License PAK............................... 5-13 5.6.2 Required software......................... 5-13 5.6.3 Product Name.............................. 5-13 5.6.4 Disk Space Requirements................... 5-13 5.6.5 Installation Account Quotas............... 5-14 5.6.6 Installation Verification Procedure....... 5-14 5.6.7 Editing the startup files and restarting DECwindows Motif environment.............. 5-14 5.6.8 Amending the LIBRARY.DECW$BOOKSHELF file...................................... 5-15 5.7 Installation of the Slovak Language Variant... 5-15 5.7.1 License PAK............................... 5-15 5.7.2 Required software......................... 5-16 5.7.3 Product Name.............................. 5-16 5.7.4 Disk Space Requirements................... 5-16 5.7.5 Installation Account Quotas............... 5-16 5.7.6 Installation Verification Procedure....... 5-17 5.7.7 Editing the startup files and restarting DECwindows Motif environment.............. 5-17 5.7.8 Amending the LIBRARY.DECW$BOOKSHELF file...................................... 5-17 5.8 Installation of the Russian Language Variant....................................... 5-18 5.8.1 License PAK............................... 5-18 5.8.2 Required software......................... 5-18 5.8.3 Product Name.............................. 5-18 5.8.4 Disk Space Requirements................... 5-19 5.8.5 Installation Account Quotas............... 5-19 5.8.6 Installation Verification Procedure....... 5-19 5.8.7 Editing the startup files and restarting DECwindows Motif environment.............. 5-20 5.8.8 Amending the LIBRARY.DECW$BOOKSHELF file...................................... 5-20 5.9 Installation of the Hungarian Language Variant....................................... 5-21 5.9.1 License PAK............................... 5-21 5.9.2 Required software......................... 5-21 vi 5.9.3 Product Name.............................. 5-21 5.9.4 Disk Space Requirements................... 5-21 5.9.5 Installation Account Quotas............... 5-22 5.9.6 Installation Verification Procedure....... 5-22 5.9.7 Editing the startup files and restarting DECwindows Motif environment.............. 5-22 5.9.8 Amending the LIBRARY.DECW$BOOKSHELF file...................................... 5-22 5.10 Installation of the Polish Language Variant... 5-24 5.10.1 License PAK............................... 5-24 5.10.2 Required software......................... 5-24 5.10.3 Product Name.............................. 5-24 5.10.4 Disk Space Requirements................... 5-24 5.10.5 Installation Account Quotas............... 5-25 5.10.6 Installation Verification Procedure....... 5-25 5.10.7 Editing the startup files and restarting DECwindows Motif environment.............. 5-25 5.10.8 Amending the LIBRARY.DECW$BOOKSHELF file...................................... 5-25 6 Managing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 6.1 Customizing Language Variables................ 6-1 6.2 Customizing Motif Window Manager Fontlist..... 6-1 6.3 Using the DECW$I18NTAILOR Utility............. 6-2 A Sample Installation A.1 Sample Product Authorization Key Registration.................................. A-1 A.2 Sample Installation........................... A-4 B DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation B.1 Sample Installation of the Japanese Language Variant....................................... B-1 B.2 Sample Installation of the Korean Language Variant....................................... B-6 B.3 Sample Installation of the Thai Language Variant....................................... B-10 vii B.4 Sample Installation of the Simplified Chinese Language Variant.............................. B-14 B.5 Sample Installation of the Traditional Chinese Language Variant.............................. B-18 B.6 Sample Installation of the Czech Language Variant....................................... B-22 B.7 Sample Installation of the Slovak Language Variant....................................... B-25 B.8 Sample Installation of the Russian Language Variant....................................... B-29 B.9 Sample Installation of the Hungarian language variant....................................... B-32 B.10 Sample Installation of the Polish Language Variant....................................... B-35 Index Examples 3-1 Sample IVP................................ 3-6 4-1 Sample DECW$MOTIF_TAILOR Session.......... 4-11 4-2 Sample DECW$TAILOR Session................ 4-18 A-1 Sample Product Authorization Key Registration.............................. A-1 A-2 Sample Installation....................... A-4 B-1 Sample Installation of the Japanese Language Variant.......................... B-1 B-2 Sample Installation of the Korean Language Variant................................... B-6 B-3 Sample Installation of the Thai Language Variant................................... B-10 B-4 Sample Installation of the Simplified Chinese Language Variant.................. B-14 B-5 Sample Installation of the Traditional Chinese Language Variant.................. B-18 B-6 Sample Installation of the Czech Language Variant................................... B-22 B-7 Sample Installation of the Slovak Language Variant................................... B-25 viii B-8 Sample Installation of the Russian Language Variant.......................... B-29 B-9 Sample Installation of Hungarian language variant................................... B-32 B-10 Sample Installation of the Polish Language Variant................................... B-35 Tables 1-1 Directories for Previous XUI or Motif Programming Environment................... 1-6 1-2 Process Quotas for the Installing Account................................... 1-10 1-3 Required Disk Space by Component.......... 1-11 1-4 Minimum Required System Parameter Values.................................... 1-14 1-5 Required Number of Free Global Pages and Global Sections........................... 1-17 1-6 Recommended System Parameter Values to Use with the ADD_Option....................... 1-18 4-1 DECwindows Keymap for West Europe languages................................. 4-4 4-2 Classes of OpenVMS Files That Can Be Removed with the DECW$MOTIF_TAILOR Utility................................... 4-8 4-3 Classes of Files That Can Be Added or Removed with the DECW$TAILOR Utility...... 4-15 ix _________________________________________________________________ Preface Intended Audience This manual is intended for anyone who plans to install the DECwindows Motif V1.2-3 for OpenVMS Czech, Hungarian, Japanese, Korean, Polish, Russian, Slovak, Thai, Simplified Chinese and Traditional Chinese language variants. Document Structure This manual contains the following chapters and appendixes: o Chapter 1 discusses how to prepare for installation of the DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software. o Chapter 2 details the actual installation procedure. o Chapter 3 gives startup procedures. This chapter also includes a sample Installation Verification Procedure (IVP). o Chapter 4 discusses tuning issues, customizing the environment, and removing any unwanted DECwindows Motif Worldwide Support software files. o Chapter 5 gives details about the installation of various language variants. o Chapter 6 discusses tuning issues, customizing the environment, and removing any unwanted DECwindows Motif language variant files. o Appendix A shows a sample installation of the DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software. o Appendix B shows a sample installation of DECwindows Motif V1.2-3 for OpenVMS language variants. vii Associated Documents In addition to this manual, the following documents are useful when installing DECwindows Motif software: o DECwindows Motif V1.2-3 for OpenVMS Language Variants Release Notes o Managing DECwindows Motif for OpenVMS Systems o OpenVMS System Manager's Manual o OpenVMS System Management Utilities Reference Manual o A Comparison of System Management on OpenVMS AXP and OpenVMS VAX Conventions In this manual, every use of OpenVMS Alpha means the OpenVMS Alpha operating system, every use of OpenVMS VAX means the OpenVMS VAX operating system, and every use of OpenVMS means both the OpenVMS Alpha operating system and the OpenVMS VAX operating system. In this manual, every use of DECwindows and DECwindows Motif refers to DECwindows Motif for OpenVMS software. The following conventions are used to identify information specific to OpenVMS Alpha or to OpenVMS VAX: The following conventions are also used in this manual: Ctrl/x A sequence such as Ctrl/x indicates that you must hold down the key labeled Ctrl while you press another key or a pointing device button. In examples, a key name enclosed in a box indicates that you press a key on the keyboard. (In text, a key name is not enclosed in a box.) viii . . . Horizontal ellipsis points in examples indicate one of the following possibilities: o Additional optional arguments in a statement have been omitted. o The preceding item or items can be repeated one or more times. o Additional parameters, values, or other information can be entered. . Vertical ellipsis points indicate the . omission of items from a code example . or command format; the items are omitted because they are not important to the topic being discussed. ( ) In command format descriptions, parentheses indicate that, if you choose more than one option, you must enclose the choices in parentheses. [ ] In command format descriptions, brackets indicate optional elements. You can choose one, none, or all of the options. (Brackets are not optional, however, in the syntax of a directory name in an OpenVMS file specification or in the syntax of a substring specification in an assignment statement.) { } In command format descriptions, braces surround a required choice of options; you must choose one of the options listed. boldface text Boldface text represents the introduction of a new term or the name of an argument, an attribute, or a reason (user action that triggers a callback). Boldface text is also used to show user input in Bookreader versions of the manual. ix italic text Italic text emphasizes important information and indicates complete titles of manuals and variables. Variables include information that varies in system messages (Internal error number), in command lines (/PRODUCER=name), and in command parameters in text (where device- name contains up to five alphanumeric characters). UPPERCASE TEXT Uppercase text indicates a command, the name of a routine, the name of a file, or the abbreviation for a system privilege. - A hyphen in code examples indicates that additional arguments to the request are provided on the line that follows. numbers All numbers in text are assumed to be decimal unless otherwise noted. Nondecimal radixes-binary, octal, or hexadecimal-are explicitly indicated. x 1 _________________________________________________________________ Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software This chapter describes the specific preparation and requirements for installing the DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software. This installation must be done prior to that of the DECwindows Motif V1.2-3 for OpenVMS language variants. The DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software contains an extension to DECwindows Motif to support local language input/output and graphical user- interface. It also provides application programmers a platform for writing internationalized X Window and Motif applications for the OpenVMS operating system. The DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software is a pre-requisite for the following 10 DECwindows Motif V1.2-3 for OpenVMS language variants: o DECwindows Motif/Japanese for OpenVMS o DECwindows Motif/Hangul for OpenVMS o DECwindows Motif/Hanyu for OpenVMS o DECwindows Motif/Hanzi for OpenVMS o DECwindows Motif/Thai for OpenVMS o DECwindows Motif OpenVMS User Interface/Cesky o DECwindows Motif OpenVMS User Interface/Magyar o DECwindows Motif OpenVMS User Interface/Polski o DECwindows Motif OpenVMS User Interface/Russkij o DECwindows Motif OpenVMS User Interface/Slovenski DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1-1 For more information on language variants installation, see Chapter 5. The DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software provides online release notes, which are copied to the following file during installation: SYS$HELP:DWMW_VAXU3012.RELEASE_NOTES (VAX) SYS$HELP:DWMW_AXPU3012.RELEASE_NOTES (Alpha) 1-2 Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software ________________________ Note ________________________ Digital strongly recommends that you read the release notes before proceeding with the installation of DECwindows Motif Worldwide Support Kit. Note that this document contains the Release Notes sections appropriate to all language variants listed above. For information about accessing the online release notes, see Section 2.1.4. ______________________________________________________ 1.1 License Registration Before you install and run DECwindows Motif Worldwide Support V1.2-3 software on a newly licensed node (or cluster), you must first register a License Product Authorization Key (License PAK) using the License Management Facility (LMF). The License PAK is shipped along with the kit if you ordered the license and media together; otherwise, it is shipped separately to a location based on your license order. If you are installing DECwindows Motif Worldwide Support V1.2-3 software as an update on a node or cluster already licensed for this software, you have already completed the License PAK registration requirements. You must register and load your license for DECwindows Motif Worldwide Support V1.2-3 software before you start the installation in order to run the Installation Verification Procedure (IVP) and use the software. To register a license, log in to the system manager's account (SYSTEM). Then choose one of the following options to register the license: o Invoke the SYS$UPDATE:VMSLICENSE.COM procedure. When the procedure prompts you for information, respond with data from your License PAK. o At the DCL prompt, enter the LICENSE REGISTER command with the appropriate qualifiers that correspond to License PAK information. DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1-3 If you plan to use DECwindows Motif on more than one node in a VMScluster, you will need to load the license on the other nodes after you complete this installation. For complete information about using LMF, see the OpenVMS License Management Utility Manual. See Appendix A for a sample installation of a PAK. 1.2 Supported Hardware The DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software can be installed on any supported Alpha or VAX processor. For a complete list of supported hardware, see the DECwindows Motif V1.2-3 for OpenVMS Software Product Description (SPD) for Alpha systems and the DECwindows Motif V1.2-3 for OpenVMS SPD for VAX systems. 1.3 Required Operating System Software The DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software requires OpenVMS Alpha Version 1.5 or higher and VMS Version 5.5-2 or higher. If your system is not running one of these versions before you attempt to install the DECwindows Motif V1.2-3 for OpenVMS language variants, the installation fails. The OpenVMS operating system comes with two subsets of components to support DECwindows Motif. To use DECwindows Motif, your system should be running a version of OpenVMS that includes the following components: o DECwindows Motif transports and base-system support. This support is required to install DECwindows Motif and to run DECwindows Motif applications. During the installation of OpenVMS, you were prompted to specify whether you wanted to install this option. To determine whether this option was installed during the installation of OpenVMS, enter the following command: $ DIR SYS$LIBRARY:DECW$TRANSPORT_COMMON.EXE 1-4 Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software Use the DECwindows tailoring utility (DECW$TAILOR) to tailor on the DECwindows base support files using the DECwindows save sets that were shipped with the OpenVMS kit as follows: $ RUN SYS$UPDATE:DECW$TAILOR.EXE See Section 4.3.1 for a more detailed description of this process. o DECwindows X11 display server for OpenVMS, fonts, and device drivers are necessary to display DECwindows Motif applications or any other X11 applications on your Alpha or VAX system. During the installation of OpenVMS, you were prompted to specify whether you wanted to install this option. To determine whether this option was installed during the installation of OpenVMS, enter the following command: $ DIR SYS$SYSTEM:DECW$SERVER_MAIN.EXE If the DECW$SERVER_MAIN.EXE file is not on your system, you cannot display DECwindows Motif applications on your Alpha or VAX system. However, you can run DECwindows Motif applications that display on a DECwindows X11 display server that runs on another system. The DECwindows Motif installation procedure will ask whether you want to continue the installation without workstation support. Use the DECwindows tailoring utility (DECW$TAILOR) to tailor on the device-support files and the 75 or 100 dots-per-inch (dpi) font files using the DECwindows Motif save sets shipped with the OpenVMS kit as follows: $ RUN SYS$UPDATE:DECW$TAILOR.EXE See Section 4.3.1 for a more detailed description of this process. ________________________ Note ________________________ See the release notes and cover letter for the version of the OpenVMS operating system that you are running DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1-5 for more information about the DECwindows X11 display server. ______________________________________________________ 1.4 OSF/Motif Release 1.1.3 Programming Support and XUI The X Window and OSF/Motif libraries that are shipped with DECwindows Motif V1.2-3 for OpenVMS software are incompatible with those shipped with previous versions. Run-time compatibility has been preserved, but the programming environment is not compatible. Programming in the XUI or OSF/Motif Release 1.1.3 environment that is provided in previous versions of DECwindows Motif is no longer supported in DECwindows Motif V1.2-3 for OpenVMS. However, the installation procedure gives you the option of saving the programming files that already exist on your system. If you choose to save these programming files, they will be moved to subdirectories where you can access them for programming. Specifically, the installation creates a subdirectory called [.DECW$113] in each of the directories listed in Table 1-1 and moves the previous files into the new subdirectory. Table 1-1 Directories for Previous XUI or Motif Programming __________Environment______________________________________ Directory_____Contents____New_Location_____________________ DECW$INCLUDE C header SYS$SYSROOT:[DECW$INCLUDE.DECW$113] files SYS$SYSTEM UIL SYS$SYSROOT:[SYSEXE.DECW$113] compiler SYS$LIBRARY Non-C SYS$SYSROOT:[SYSLIB.DECW$113] language ______________bindings_____________________________________ ________________________ Note ________________________ The process for using the saved programming environment is documented in the programming chapter of the release notes. ______________________________________________________ 1-6 Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1.5 Saving Customized Bookreader Files The installation procedure replaces the following file with a new version: SYS$SYSROOT:[DECW$BOOK]LIBRARY.DECW$BOOKSHELF If you have customized this file and want to save it, copy the file to another directory or rename the file prior to the installation of DECwindows Motif V1.2-3 for OpenVMS so that it is not deleted. To copy your customized file to another directory, create the directory and define a global symbol in the DECW$PRIVATE_APPS_SETUP.COM file. To create a Bookreader directory called SYS$COMMON:[DECW$BOOK_LOCAL], perform the following steps: 1. Create the directory and assign world read access as follows: $ CREATE/DIRECTORY/PROTECTION=WORLD:R - _$ SYS$COMMON:[DECW$BOOK_LOCAL] 2. Copy the LIBRARY.DECW$BOOKSHELF Bookreader file to the new directory as follows: $ COPY SYS$SYSROOT:[DECW$BOOK]LIBRARY.DECW$BOOKSHELF - _$ SYS$COMMON:[DECW$BOOK_LOCAL]/LOG 3. If the SYS$MANAGER directory does not contain the DECW$PRIVATE_APPS_SETUP.COM command file, copy the template file to a command file as follows: $ COPY SYS$MANAGER:DECW$PRIVATE_APPS_SETUP.TEMPLATE - _$ SYS$MANAGER:DECW$PRIVATE_APPS_SETUP.COM/LOG 4. Edit the DECW$PRIVATE_APPS_SETUP.COM file and define the global symbol DECW$BOOK to point to your Bookreader directory by adding the following line to the file: $ DECW$BOOK == "SYS$COMMON:[DECW$BOOK_LOCAL]" 5. Restart DECwindows Motif using the following command: $ @SYS$MANAGER:DECW$STARTUP RESTART DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1-7 For more information about customizing your DECwindows Motif environment, see the Managing DECwindows Motif for OpenVMS Systems manual. 1.6 Product and Device Names During the installation, tell the system which product is being installed and which drive contains the distribution media. Refer to a product with its facility name and version; refer to a drive with its device name. Product and device names use the following formats: o facvvu Represents the facility name and version number of the product being installed, also known as the installation name. The following table explains the format of facvvu. o ddcu The device name of the source drive that holds the distribution media. For the DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software installation, use the installation name DWMW_AXPU3012 for Alpha systems and DWMW_VAXU3012 for VAX systems. For additional information about the device names of devices on your system, see the upgrade and installation supplement for your Alpha or VAX processor. ___________________________________________________________ Variable__Definition_______________________________________ fac Product name code (1 to 36 alphanumeric characters) vv Major version number (2 digits) u_________Update_number_(1_digit)__________________________ 1.7 Installation Procedure Requirements The VMSINSTAL installation procedure is used to install OpenVMS updates and layered software products, including DECwindows Motif software. This section discusses the VMSINSTAL installation procedure requirements for installing your DECwindows Motif software. 1-8 Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software When you invoke VMSINSTAL, the installation procedure checks the following: o Whether you are logged in to an appropriately privileged account o Whether any other users are logged in to the system o Whether you have the minimum required system account quotas and limits o Whether you have the minimum required disk space o Whether you have the minimum required system parameter values Prepare to install DECwindows Motif software by logging in to a privileged account, such as the system manager (SYSTEM) account. See Section 1.7.1 for the prerequisite privileges. Although Digital prefers that you perform the installation using the operator console or other hardcopy terminal, you can perform the installation from a DECterm window. _______________________ Caution _______________________ If you use a DECterm window to perform the installation, make sure that no other DECwindows Motif functions are invoked while the installation is running. ______________________________________________________ 1.7.1 Process Privileges To install DECwindows Motif, you must be logged in to an account that has SETPRV or at least the following privileges: o CMKRNL o WORLD o SYSPRV VMSINSTAL turns off the BYPASS privilege at the start of the installation and turns it back on when the installation is completed. DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1-9 1.7.2 Process Account Quotas VMSINSTAL requires that the installation account has the minimum quotas shown in Table 1-2. Table_1-2_Process_Quotas_for_the_Installing_Account________ Quota_Name__Value__________________________________________ ASTLM 24 BIOLM 18 BYTLM 18000 DIOLM 18 ENQLM 30 FILLM__________20__________________________________________ Use the OpenVMS Authorize utility to verify and change process quotas for the installation account in the user authorization file (UAF). (Some sites may restrict the use of the OpenVMS Authorize utility to certain accounts or users.) For example, to change the BYTLM quota for the account-name installation account, enter the following commands: $ SET DEFAULT SYS$SYSTEM $ RUN AUTHORIZE UAF> SHOW account-name UAF> MODIFY account-name /BYTLM = 18000 UAF> SHOW account-name UAF> EXIT $ LOGOUT After the quotas for the installation account have been changed, log out of the installation account and log in again for the new quotas to take effect. You can then proceed with the installation. User account quotas are stored in the file SYS$SYSTEM:SYSUAF.DAT. For more information about modifying account quotas, see the description of the Authorize utility in the OpenVMS System Management Utilities Reference Manual. 1-10 Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1.7.3 Disk Space Use Table 1-3 to determine the amount of free disk space that is required on the system disk to install DECwindows Motif components. However, because you can choose not to install all the components, your actual disk space requirement may be less. To determine the number of free blocks on the system disk, enter the following command: $ SHOW DEVICE SYS$SYSDEVICE Table_1-3_Required_Disk_Space_by_Component_________________ Component__________________Alpha____VAX____________________ Base kit 127000 80000 Programming environment 15000[1]14000[1] Example programs 14000 13000 Translated-image support 53000 Not applicable Total disk space 209000 107000 required: [1]This_number_includes_all_programming_language_support.__ The actual number of blocks required may be fewer depending on the language support you select. ___________________________________________________________ The installation procedure checks for free disk space on the system disk. If sufficient space is not available, the installation procedure provides the following options: o Install fewer optional files. o Restart the installation and specify another disk to use as an alternate working device. See Section 1.7.3.1 for information about how to use an alternate working device. o Terminate the installation, create more free disk space on the system disk, and start the installation again. DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1-11 o Continue the installation and risk running out of disk space. ________________________ Note ________________________ If you run out of free disk space during the installation, the installation procedure fails. ______________________________________________________ 1.7.3.1 Using an Alternate Working Device You can use the alternate working device (AWD) option to specify another disk to store the files temporarily while they are being unpacked from the save sets on the distribution media. Once the save sets have been unpacked, the installation procedure will add or replace the files that are necessary for the installation of DECwindows Motif from the AWD to the system disk. If this installation is to upgrade an existing DECwindows Motif environment, then the AWD option allows you to perform an installation with fewer free blocks on the system disk than are otherwise required. The VMSINSTAL procedure creates a temporary working directory either on the AWD device or by default in the following location: SYS$SYSROOT:[SYSUPD.facvvu] If you use the AWD option, you can specify a directory. Specifying a directory is optional, but the following guidelines apply: o If you specify an existing directory, VMSINSTAL creates a working directory as a subdirectory within the directory that you specify (for example, [WORK.facvvu]). VMSINSTAL deletes the working subdirectory after the installation is completed. o If you do not specify a directory, the VMSINSTAL procedure creates a working directory on the specified device with a directory specification of [000000.facvvu]. VMSINSTAL deletes the working directory after the installation is completed. 1-12 Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software o If you specify a nonexistent directory, VMSINSTAL creates both the specified directory and a working directory as a subdirectory within the directory that you specify. VMSINSTAL deletes only the working directory and not the originally specified directory after the installation is completed. You must delete the specified directory manually. Use the following format to invoke VMSINSTAL and specify the AWD option: $ @SYS$UPDATE:VMSINSTAL facvvu dkcu OPTIONS N,AWD=ddcu:[dir] Use the following definitions for the variables in the previous command line: o For facvvu, supply the product name and version number. For the DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software installation, the value of facvvu is DWMW_AXPU3012 for Alpha systems and DWMW_VAXU3012 for VAX systems. o For dkcu, give the device name of the source drive that holds the distribution media. o For ddcu, give the device name of the alternate working device. o For dir, specify the name of the directory on the alternate working device where the product subdirectory will be created. The default is [000000]. For example, to install DECwindows Motif from the compact disc on to an OpenVMS Alpha system using DKA2 as the alternate working device, enter the following command: $ @SYS$UPDATE:VMSINSTAL DWMW_AXPU3012 source-drive - _$ OPTIONS N,AWD=DKA2: 1.7.3.2 Using the Distributed File Service You can specify a temporary working directory on a disk that uses the Distributed File Service (DFS). If you use a DFS-mounted disk as your alternate working device, the installation procedure erroneously reports that there is -1 free blocks on the alternate working device. This error occurs because the DFS client (the installation DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1-13 procedure, in this case) cannot determine the amount of free disk space on the DFS-mounted disk. Before using a DFS-mounted disk, manually determine its free disk space. Log in to the system on which the disk is mounted, and enter the SHOW DEVICE command as follows: $ SHOW DEVICE 1.7.4 System Parameters Table 1-4 lists the minimum required system parameter values for the installation. Depending on the kinds of programs and applications running at your site, you might need higher values for some settings. Table_1-4_Minimum_Required_System_Parameter_Values_________ System_Parameter______Alpha_Value______VAX_Value___________ GBLSECTIONS 600[1] 420[1] GBLPAGES 80000[1] 62000[1] GBLPAGFIL 1024 6024 SWPOUTPGCNT 512 500 MAXBUF 8192 2048 VIRTUALPAGECNT 73536 50000 CHANNELCNT 255 255 PROCSECTCNT 64 40 PQL_DPGFLQUOTA - 32768 PQL_MPGFLQUOTA 32768 - PQL_MASTLM 100 100 PQL_MBIOLM 100 100 [1]If_you_have_installed_other_software_that_uses_global___ pages or global sections, you might need a higher minimum value. When you boot your system and DECwindows Motif starts, the values of free GBLPAGES and GBLSECTIONS are checked for your system. If you do not have sufficient values for GBLPAGES and GBLSECTIONS, the DECwindows Motif startup procedure prints a warning and provides a recommended value for these parameters. (continued on next page) 1-14 Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software Table_1-4_(Cont.)_Minimum_Required_System_Parameter_Values_ System_Parameter______Alpha_Value______VAX_Value___________ PQL_MBYTLM 100000 40000 PQL_MDIOLM 100 100 PQL_MENQLM 300 200 PQL_MFILLM 100 100 PQL_MPRCLM 10 8 PQL_MWSDEFAULT 1024 512 PQL_MWSQUOTA 2048 1024 PQL_MWSEXTENT 8192 2048 WINDOW_SYSTEM 1 1 NPAGEDYN 670000 735000 PAGEDYN 289000 274000 WSMAX__________________12000_____________4096______________ _______________________ Caution _______________________ If you do not ensure that your system has the necessary amount of global pages and global sections for the installation, the DCL tables can become corrupted. ______________________________________________________ 1.7.5 Additional System Maintenance Procedures This section explains how to use the System Generation utility (SYSGEN) and the AUTOGEN utility to prepare your system for an installation of DECwindows Motif. AUTOGEN uses system configuration data to automatically set system parameters. 1.7.5.1 Checking System Parameter Values To check the values of your system parameters, invoke SYSGEN by entering the following command at the DCL prompt: $ RUN SYS$SYSTEM:SYSGEN SYSGEN> DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1-15 At the SYSGEN> prompt, enter the SHOW command to display the value of a system parameter. The following command displays the value for the MAXBUF system parameter: SYSGEN> SHOW MAXBUF After checking the parameters with the SHOW command, enter the EXIT command at the SYSGEN> prompt to return to DCL level. If the current values are less than the values in Table 1-4, you must increase the system parameter settings. Section 1.7.5.3 describes the procedures for using the AUTOGEN utility to increase these values. 1.7.5.2 Calculating the Amount of Free Global Pages and Global Sections If your system parameter values are equal to or greater than the minimum values specified in Table 1-4, then you can continue with the installation of DECwindows Motif. However, to install and run DECwindows Motif, you must have sufficient free global pages and global sections for DECwindows Motif and for SYS$LIBRARY:DCLTABLES.EXE. First determine how many free global pages and global sections you have on your system and how many are required to reinstall a new version of SYS$LIBRARY:DCLTABLES.EXE. Then, if necessary, use AUTOGEN to increase the GBLPAGES and GBLSECTIONS system parameters. Enter the following DCL command to determine the number of global pages required for SYS$LIBRARY:DCLTABLES.EXE: $ DIR/SIZE SYS$LIBRARY:DCLTABLES.EXE This command returns the size (in blocks) of the SYS$LIBRARY:DCLTABLES.EXE file. As an approximation, use this figure as the number of global pages needed for the file. Enter the WRITE command with the F$GETSYI lexical function to find the number of free global pages and global sections. The following example shows how to obtain this information at your terminal (the default for SYS$OUTPUT): 1-16 Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software $ WRITE SYS$OUTPUT F$GETSYI("CONTIG_GBLPAGES") 15848 $ WRITE SYS$OUTPUT F$GETSYI("FREE_GBLSECTS") 24 See Table 1-5 to determine whether the amount of free global pages and global sections is sufficient. If these values are not high enough to continue with the installation, then see Section 1.7.5.3, which describes the procedures for increasing these values using AUTOGEN. Note that if your system does not have a sufficient amount of free global pages and global sections, the installation can not continue. Table 1-5 Required Number of Free Global Pages and Global __________Sections_________________________________________ ____________Currently_Running_DECwindows_Motif_____________ System_Parameter______Alpha_Value______VAX_Value___________ GBLPAGES 20000 8000 GBLSECTIONS 60 40 ___________________________________________________________ __________Not_Currently_Running_DECwindows_Motif___________ System_Parameter______Alpha_Value______VAX_Value___________ GBLPAGES 56000 26000 GBLSECTIONS_____________210______________140_______________ 1.7.5.3 Changing System Parameter Values Using the AUTOGEN Utility Use the AUTOGEN command procedure to change system parameters. AUTOGEN automatically adjusts values for parameters that are associated with the values you reset manually. To change system parameters with AUTOGEN, edit the file SYS$SYSTEM:MODPARAMS.DAT. To change a parameter value listed in this file, delete the current value associated with that parameter and enter the new value. DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1-17 To add a new parameter, add a line to the file that includes both the name of the parameter and its value. For example: MIN_MAXBUF = 8192 To modify incremental adjustments to parameters, such as global pages and global sections, use ADD_. The following example increases the global page setting by 20000: ADD_GBLPAGES = 24000 Table 1-6 lists the system parameters that you need to adjust incrementally. Table 1-6 Recommended System Parameter Values to Use with __________the_ADD_Option___________________________________ System_Parameter______Alpha_Increment__VAX_Increment_______ SYSMWCNT - 195 GBLSECTIONS 180 130 GBLPAGES 44000 24000 GBLPAGFIL 768 5000 NPAGEDYN 150000 305000 PAGEDYN________________76000____________64000______________ ________________________ Note ________________________ When you set the page-file quota, do not use a value that exceeds the amount of page-file space available on the system. ______________________________________________________ After you make all your changes, exit from the file and execute the AUTOGEN procedure to recalculate your system parameters. Enter the following command to recalculate your system parameters and reboot the system: $ @SYS$UPDATE:AUTOGEN GETDATA REBOOT 1-18 Preparing to Install DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software When you specify REBOOT, AUTOGEN performs an automatic system shutdown and then reboots the system. Any users logged in to the system are immediately disconnected during the shutdown. The automatic reboot puts the new parameter values into effect. For details about using AUTOGEN, see the section about the AUTOGEN utility in the OpenVMS System Manager's Manual: Tuning, Monitoring, and Complex Systems and the AUTOGEN section in System Management Utilities Reference Manual: A-l. 1.7.6 Backing Up Your System Disk Digital recommends that you back up your system disk before installing any software. At the beginning of the installation, VMSINSTAL asks whether your system disk is backed up. Use the backup procedures that are established at your site. For details about performing a system disk backup, see the section on the Backup utility in the OpenVMS System Management Utilities Reference Manual. 1.7.7 Notifying Other Users To make sure that you are the only user logged in to the system, follow these steps: 1. Notify current users to log out. Enter the following command: $ REPLY/ALL/BELL/SHUTDOWN "Log out for the installation of - _$ DECwindows Motif wordlwide support 1.2-3 for OpenVMS please..." 2. Enter the following command to prevent nonprivileged users from logging in to the system: $ SET LOGINS/INTERACTIVE=0 DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Software 1-19 2 _________________________________________________________________ Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS This chapter explains how to install the DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software using the VMSINSTAL procedure. Included is a step-by-step description of the installation procedure, information about error recovery, and instructions for accessing the release notes. The DECwindows Motif installation takes approximately 45 minutes, depending on the processor type. The VMSINSTAL command procedure installs the DECwindows Motif product on your system disk. ________________________ Note ________________________ A Product Authorization Key (PAK) for DECwindows Motif must be registered and loaded before starting the DECwindows Motif installation. ______________________________________________________ _______________________ Caution _______________________ If you do not have a satisfactory backup copy of your system disk, do not attempt to install DECwindows Motif software. Back up the system disk (as described in the OpenVMS upgrade and installation supplement for your Alpha or VAX processor) before you install the DECwindows Motif software. Before beginning the installation procedure, review Chapter 1 for more information about installation preparations and requirements. ______________________________________________________ Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2-1 2.1 Installation Procedure The DECwindows Motif installation procedure consists of a series of questions and informational messages. Enter a question mark (?) for help at any time during the installation. See Appendix A for a sample installation. To end the installation procedure, press Ctrl/Y. When you press Ctrl/Y, the installation procedure deletes all files created up to that point and then exits. You can then start the installation again. 2.1.1 Invoking VMSINSTAL To start the installation, invoke the VMSINSTAL command procedure from a privileged account, such as the SYSTEM account. The VMSINSTAL.COM file is located in the SYS$UPDATE directory. When the system prompts you with a question during the installation procedure, the default answer is often listed in brackets ([]). Perform the following steps to run the VMSINSTAL command procedure and to install the DECwindows Motif software: 1. Locate the DECwindows Motif V1.2-3 for OpenVMS distribution media. 2. If your system is not already running, start up the system and log in to a privileged account, such as the system manager (SYSTEM) account. 3. Place the distribution media in the source drive. If your DECwindows Motif distribution kit contains more than one piece of media, place the first piece in the drive. During the installation procedure, you will be prompted to load the next piece of media. The paper labels on the media indicate the order in which you load them. 4. Start the VMSINSTAL procedure. On the command line, specify the product name, DWMW_AXPU3012 for Alpha systems or DWMW_VAXU3012 for VAX systems. 2-2 Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Specify OPTIONS N to access the release notes contained in your media kit. The DECwindows Motif V1.2-3 for OpenVMS language variants Release Notes can be displayed or printed before the installation begins. Enter the following command: $ @SYS$UPDATE:VMSINSTAL DWMW_xxxU3012 ddcu: OPTIONS N ________________________ Note ________________________ This example is being used to illustrate an installation of DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software on both an Alpha system and a VAX system. This example substitutes xxx wherever Alpha or VAX normally appears. Substitute the correct letters for your system (Alpha or VAX) in place of xxx. ______________________________________________________ For ddcu, specify the device name of the source drive that holds the distribution media. See Section 1.6 for more information about the format of product and device names. Also, see the OpenVMS upgrade and installation supplement for your Alpha or VAX processor. If you are installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software using the alternate working device (AWD) option described in Chapter 1, invoke the VMSINSTAL command procedure as follows: $ @SYS$UPDATE:VMSINSTAL DWMW_xxxU3012 ddcu: OPTIONS N,AWD=ddcu:[dir] The first ddcu instance is the device name of the source drive that holds the distribution media. The second ddcu instance is the device name of the AWD, which is the target device. The variable dir is the name of the directory on the alternate working device in which the product subdirectory is created. The default directory is [000000]. If the VMSINSTAL command fails, check whether any of the following conditions occurred: o You entered the product name incorrectly. VMSINSTAL displays the following message: %VMSINSTAL-E-NOPRODS, None of the specified products were found Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2-3 o You specified an incorrect name for the source drive. VMSINSTAL displays an "invalid device" error message and prompts you until you enter the name of a source device that exists on the system. Remember to enter a colon (:) after the device name. The VMSINSTAL procedure displays messages similar to the following: OpenVMS xxx Software Product Installation Procedure It is 30-Jan-1994 at 08:02 Enter a question mark (?) at any time for help. 2.1.2 Confirming System Backup The VMSINSTAL procedure asks the following question: * Are you satisfied with the backup of your system disk [YES]? If you made a backup copy of your system disk, press the Return key and proceed to Section 2.1.3. If you did not make a backup copy of the system disk, do the following: 1. Enter NO and press the Return key. The VMSINSTAL procedure exits and returns you to DCL level. 2. Back up the system disk as described in the OpenVMS upgrade and installation supplement for your Alpha or VAX processor. 3. After you make a backup copy of the system disk, start the installation procedure again from step 4 in Section 2.1.1. 2.1.3 Mounting Distribution Media VMSINSTAL instructs you to mount the first volume of the set. Load the volume and enter YES, as follows: Please mount the first volume of the set on ddcu. When the installation begins, VMSINSTAL displays informational text similar to the following: 2-4 Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS The following products will be processed: DWMW_xxxU3 V1.2 Beginning installation of DWMW_xxxU3 V1.2 at 08:04 %VMSINSTAL-I-RESTORE, Restoring product save set A... 2.1.4 Choosing a Release Notes Option If you specify OPTIONS N during step 4 in Section 2.1.1, VMSINSTAL now prompts you to choose a release notes option: Release notes included with this kit are always copied to SYS$HELP. Additional Release Notes Options: 1. Display release notes 2. Print release notes 3. Both 1 and 2 4. None of the above * Select option [2]: Enter the number of the option you want: o Option 1 displays the release notes on the terminal. o Option 2 prints the release notes (default). o Option 3 displays and prints the release notes. o Option 4 allows you to continue with the installation if you do not want to display or print the release notes. ________________________ Note ________________________ Digital recommends that you read the release notes before continuing the installation. ______________________________________________________ If you choose option 1, the release notes are displayed on the terminal. You are prompted to press Return to continue reading the release notes. If you want to end the display and continue with the installation, press Ctrl/C. After you press Ctrl/C, you are asked whether you want to continue with the installation and are informed that the release notes have been moved to SYS$HELP. Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2-5 _______________________ Caution _______________________ Do not press Ctrl/Y; if you do, the installation will end. ______________________________________________________ If you choose option 2 or 3, you are prompted for the name of the print queue. If you do not specify a print queue, the release notes are queued to SYS$PRINT by default. 2.1.5 Continuing the Installation After the VMSINSTAL procedure processes your release notes option, the following message is displayed: * Do you want to continue the installation [NO]? If you want to continue with the installation, enter YES. If you want to end the installation, press the Return key. Regardless of the release notes option you select, the VMSINSTAL procedure copies the release notes to the SYS$HELP directory. See Section 2.3 for information about how to access the release notes once they are copied to the SYS$HELP directory. %VMSINSTAL-I-RELMOVED, Product's release notes have been moved to SYS$HELP. *** Installing DECwindows Motif V1.2-3 Worldwide Suppoprt for OpenVMS xxx software *** Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to and embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. 2-6 Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2.1.6 Preserving the OSF/Motif Release 1.1.3 Programming Environment If DECwindows Motif for OpenVMS Version 1.1 is already installed on your system, the previous programming environment (OSF/Motif Release 1.1.3) is incompatible with the DECwindows Motif V1.2-3 for OpenVMS software. The procedure asks whether you want to preserve the previous programming environment: The DECwindows Motif programming environment was installed with a previous version of this kit. This environment is incompatible with the OSF/Motif Release 1.2 environment provided with DECwindows Motif worldwide support 1.2-3. The XUI programming environment is also no longer included in DECwindows worldwide support 1.2-3. If you intend to continue developing programs for XUI or OSF/Motif Release 1.1.3 you should save this environment. Please refer to the installation guide for more details and information on accessing these files in their new location. If you do not choose to save the XUI and OSF/Motif Release 1.1.3 programming environment, those files will be removed from the system disk. * Do you want to save the OSF/Motif Release 1.1.3 and XUI * programming support files [N]? If you want to preserve the previous programming environment, enter YES (or Y) and press the Return key. The installation procedure creates subdirectories that contain the previous programming files so that they can be used for programming at a later time. See Section 1.4 to learn how to reference the previous version of the programming support files. 2.1.7 Installing the Entire Kit You can install the entire DECwindows Motif software kit, or you can install part of the kit. The DECwindows Motif base kit is always installed; the DECwindows Motif programming environment is optional. Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2-7 The procedure asks you whether you want to install the entire kit: You can install the DECwindows Motif kit completely or in selected portions. A complete installation requires as many as 209,000 blocks. If you choose to perform a partial installation, you can select (tailor) the programming support files that support your DECwindows Motif application development. Whether you perform a complete or partial installation, this kit provides support for running DECwindows Motif applications on OpenVMS compute servers. * Do you want to install the entire kit [Y]? If you want to install the entire kit, press the Return key and verify your kit selections (see Section 2.1.9). If you do not want to install the entire kit, enter NO and continue with questions about installing programming support, (see Section 2.1.8). 2.1.8 Choosing Programming Support Files The installation procedure asks whether you want to install programming support: This installation procedure provides support files for developing DECwindows Motif applications in several programming languages. These files are needed only to develop applications and are not required to run DECwindows Motif applications. The free disk space requirement for each programming support file ranges from 3000 to 8000 blocks. * Do you want to install DECwindows Motif programming support [Y]? Press the Return key to install programming support. The following message is displayed: Support files are supplied for the following OpenVMS programming languages: Fortran, Pascal In addition, support files are supplied for programming in the C language using conventions and standards developed at the Massachusetts Institute of Technology. If you do not want to install programming support, enter NO and proceed to the instructions in Section 2.1.9. The procedure asks whether you want to install all of the programming support files: * Do you want to install all programming language support files [Y]? 2-8 Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Press the Return key if you want to install all the languages. If you do not want to install all the languages, enter NO. Each language is then displayed. Enter YES for each language you want to install. The procedure asks whether you want to install DECwindows Motif programming example files: * Do you want to install DECwindows Motif programming examples [Y]? Press Return if you want to install the programming example files. If you enter NO, the example files are not installed. On Alpha systems, the procedure asks whether you want to install DECwindows Motif translated-image support: This installation procedure provides support files for running your DECwindows Motif OpenVMS VAX applications on OpenVMS Alpha systems using the DECmigrate product. These files support applications developed for the OSF/Motif Release 1.1.3 toolkit. These files are not required to run DECwindows Motif OpenVMS Alpha applications. The free disk space requirement for these support files is approximately 53,000 blocks. * Do you want to install DECwindows Motif for OpenVMS Alpha * translated image support [Y]? Press Return if you want to install translated-image support. If you enter NO, translated-image support is not installed. 2.1.9 Verifying Kit Selections The components of the kit that you have chosen are now displayed, and you can verify that these choices are correct. A message similar to the following is displayed: You have selected the following portions of the kit: o DECwindows Motif Applications and Run-time Libraries o DECwindows Motif for OpenVMS Alpha translated image support o DECwindows Motif programming examples o DECwindows Motif programming support Fortran, Pascal MIT C language programming conventions Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2-9 o OSF/Motif Release 1.1.3 and XUI saved programming support * Are these selections correct [Y]? Press the Return key if the choices are correct. If you want to change your choices, enter NO. You are prompted by the previous questions again, beginning with whether you want to install the entire kit (see Section 2.1.7). After you repeat the selection procedure and are satisfied with your selections, enter YES and press the Return key. 2.1.10 Verifying Disk Space The installation procedure checks whether your system disk contains a sufficient number of free blocks. 1. If the blocks are available, the installation continues (see Section 2.1.11). 2. If you do not have sufficient system disk space to install the portions you chose, the installation displays a message similar to the following: Your system disk has only 25364 free blocks, and you have selected to install approximately 106050 blocks. * * * N O T E * * * The installation procedure has determined that you do not have enough disk space to complete the installation. However, it may be possible to continue successfully if you are installing DECwindows Motif on a system that already has DECwindows Motif installed. * Do you want to reselect which DECwindows Motif options to install [Y]? If you press the Return key, you can reselect the DECwindows Motif options beginning with those described in Section 2.1.7. If you enter NO, the procedure asks whether you want to continue the installation: * Do you want to continue the installation anyway [Y]? _______________________ Caution _______________________ If you press the Return key, the installation continues. However, if you run out of disk space, the installation fails. ______________________________________________________ 2-10 Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS If you enter NO, the installation ends. You can then either free up blocks on the system disk and restart the installation, or start the installation again using the AWD option. (See Section 1.7.3.1 for information about using the AWD option.) 3. If you specify an alternate working device that does not have sufficient disk space to install the portions you have chosen, the installation displays a message similar to the following: Your specified alternate working directory device has only 68977 free blocks, and this installation will require approximately 106050 blocks. You should either reselect which DECwindows Motif options to install, or restart this installation using an alternate working directory device with more free blocks. * * * NOTE * * * Although the installation procedure estimates you do not have enough disk space to complete the installation, it may be possible to continue successfully if you are installing DECwindows Motif on a system which already has DECwindows installed. * Do you want to reselect which DECwindows Motif options to install [Y]? If you press the Return key, you can reselect the DECwindows Motif options beginning with those described in Section 2.1.7. If you enter NO, the procedure asks whether you want to continue the installation: * Do you want to continue the installation anyway [Y]? If you press the Return key, the installation continues. _______________________ Caution _______________________ Note that if you lack sufficient free disk space for installation on the alternate working device, the installation procedure ends. ______________________________________________________ If you enter NO, the installation procedure ends. Restart the installation once you set up an alternate working device with sufficient disk space. (See Section 1.7.3.1 for more information about using the AWD option.) Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2-11 2.1.11 Verifiying License Registration The installation procedure continues and displays license information similar to the following: A registered and loaded product authorization key for DW-MOTIF is required to run any DECwindows Motif for OpenVMS application. If you answer NO to the next question, the installation of DECwindows Motif for OpenVMS will be terminated. Product: DW-MOTIF Producer: DEC Version: Release Date: * Does this product have an authorization key registered and loaded ? Enter YES to continue with the installation if your authorization key is registered and loaded. If you enter NO, the following message is displayed and the installation ends: Installation of DECwindows Motif cannot continue because you do not have a registered and loaded authorization key. See Section 1.1 for more information about license registration. After you register and load your authorization key, restart the DECwindows Motif installation, beginning at step 4 in Section 2.1.1. 2.1.12 Performing a System Reboot The installation procedure suggests that you perform a system reboot to ensure successful installation of DECwindows Motif: DECwindows Motif will not start if your system parameters are not correct. o If you allow a system shutdown, the installation procedure will reboot the system at the end of the installation. If your system parameters are incorrect, the installation will run AUTOGEN prior to the system reboot. o If you do not allow a system shutdown, the installation procedure will continue, and you will be informed at the end of the installation whether you need to modify your system parameters in order to start DECwindows Motif. 2-12 Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS To complete the installation of this product, you should reboot the system. If it is not convenient to reboot at this time, then enter NO to the following question. If you enter NO, the installation procedure will continue. * Will you allow a system reboot after this product is installed [YES]? ________________________ Note ________________________ Although the installation dialog indicates that a system reboot is necessary to complete the installation, it may not be needed. The VMSINSTAL procedure automatically displays this message. During the installation you will be informed whether it is necessary for the system to be rebooted. ______________________________________________________ If you enter NO to the shutdown question, no further questions are asked. If you answered YES to the shutdown question, the VMSINSTAL procedure displays the following questions about the shutdown: * How many minutes for system shutdown [0]? * Do you want to do an automatic system reboot [YES]? No further questions will be asked. _______________________ Caution _______________________ To avoid confusion with file versions when activating an image or application, perform the necessary commands to restart the DECwindows Motif V1.2-3 for OpenVMS software as indicated during the installation in Section 2.1.14. ______________________________________________________ Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2-13 2.1.13 Reading Informational Messages VMSINSTAL lists the directories that are created and the save sets that are restored. VMSINSTAL prints out a message indicating that the files will be moved to their target directories. o If you perform the installation using media other than 9-track magnetic tape, messages similar to the following are displayed: %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$INCLUDE.DECW$113]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSEXE.DECW$113]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSLIB.DECW$113]. %VMSINSTAL-I_RESTORE, Restoring product save set B ... %VMSINSTAL-I_RESTORE, Restoring product save set C ... %VMSINSTAL-I_RESTORE, Restoring product save set D ... %VMSINSTAL-I-RESTORE, Restoring product save set E ... %VMSINSTAL-I-RESTORE, Restoring product save set J ... %VMSINSTAL-I-RESTORE, Restoring product save set L ... %VMSINSTAL-I-RESTORE, Restoring product save set N ... %VMSINSTAL-I-RESTORE, Restoring product save set O ... %VMSINSTAL-I-RESTORE, Restoring product save set P ... %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... Final stage of installation is in process. %VMSINSTAL-I-RESTORE, Restoring product save set S ... This product creates system directory VMI$ROOT:[SYSUPD.DECWMI18N123] %VMSINSTAL-I-RESTORE, Restoring product save set T ... %VMSINSTAL-I-RESTORE, Restoring product save set U ... %VMSINSTAL-I-RESTORE, Restoring product save set V ... %VMSINSTAL-I-RESTORE, Restoring product save set W ... %VMSINSTAL-I-RESTORE, Restoring product save set X ... %VMSINSTAL-I-RESTORE, Restoring product save set Y ... o If you perform the installation using 9-track magnetic tape, some of the files are in compressed text libraries. The installation procedure informs you that the data is being decompressed and displays messages similar to the following: 2-14 Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS %VMSINSTAL-I_RESTORE, Restoring product save set B... %VMSINSTAL-I_RESTORE, Restoring product save set C... %VMSINSTAL-I_RESTORE, Restoring product save set D... %VMSINSTAL-I_RESTORE, Restoring product save set E... Decompressing H_E_DECW$INCLUDE Decompressing H_E_SYSLIB %VMSINSTAL-I_RESTORE, Restoring product save set J... %VMSINSTAL-I_RESTORE, Restoring product save set L... %VMSINSTAL-I_RESTORE, Restoring product save set N... %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... Final stage of installation is in process. %VMSINSTAL-I-RESTORE, Restoring product save set S ... This product creates system directory VMI$ROOT:[SYSUPD.DECWMI18N123] %VMSINSTAL-I-RESTORE, Restoring product save set T ... %VMSINSTAL-I-RESTORE, Restoring product save set U ... %VMSINSTAL-I-RESTORE, Restoring product save set V ... %VMSINSTAL-I-RESTORE, Restoring product save set W ... %VMSINSTAL-I-RESTORE, Restoring product save set X ... %VMSINSTAL-I-RESTORE, Restoring product save set Y ... The installation procedure then informs you that a spurious error message will be displayed, which you can safely ignore: You may safely ignore the following NCP error message(s). %NCP-W-SYSMGT, System-specific management function not supported %NCP-W-SYSMGT, System-specific management function not supported %NCP-W-SYSMGT, System-specific management function not supported You are then notified that you should run the Installation Verification Procedure (IVP) after the installation has completed and after you have started DECwindows Motif. (See Section 3.2 for more information about running the IVP.) The Installation Verification Procedure (IVP) should be run after the installation has been completed and DECwindows Motif has been restarted. The IVP can be found in SYS$TEST:DECW$IVP.COM. Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2-15 2.1.14 Using AUTOGEN to Set System Parameters The installation procedure might automatically run AUTOGEN, depending on which of the following type of system you are using: o A nonworkstation system If you are installing DECwindows Motif on a nonworkstation system (that is, a OpenVMS host system), the following message is displayed: This system is not a workstation. It will not be necessary to run AUTOGEN. o A workstation system running DECwindows Motif with correct system parameters If you are installing DECwindows Motif on a workstation system and your system parameters are correct, the following message is displayed: The installation procedure has determined that your system parameters are set correctly and that it will not be necessary to run AUTOGEN or reboot the system. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $ @SYS$MANAGER:DECW$STARTUP RESTART If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $ @SYS$MANAGER:DECW$STARTUP * * * N O T E * * * If you are installing DECwindows Motif from your workstation console, log off after you enter the command to start DECwindows Motif. o A workstation system running DECwindows Motif with incorrect system parameters If you are installing DECwindows Motif on a workstation system and your system parameters need to be reset, the following message is displayed: 2-16 Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS The installation of DECwindows Motif has determined that some of your system parameter values will require modification in order to start DECwindows Motif worldwide support 1.2-3 for OpenVMS. To set your parameters correctly, run AUTOGEN using the following DCL command: $ @SYS$UPDATE:AUTOGEN GETDATA REBOOT CHECK_FEEDBACK This will adjust your system parameters and reboot the system. o A workstation system running DECwindows Motif with incorrect system parameters and you answered YES to a system shutdown The OpenVMS AUTOGEN procedure will now be run to set your system parameters. After that, your system will be automatically rebooted. After the system has been rebooted, successful installation of the workstation software will be indicated by the appearance of the Start Session window. %AUTOGEN-I-BEGIN, GETDATA phase is beginning. . . . %AUTOGEN-I-BEGIN, GENPARAMS phase is beginning. . . . %AUTOGEN-I-BEGIN, GENFILES phase is beginning. . . . %AUTOGEN-I-BEGIN, SETPARAMS phase is beginning. . . . Installation of DWMW_xxxU3 V1.2 completed at 08:37 %VMSINSTAL-I-SHUTDOWN, This product requires that the system be rebooted. SHUTDOWN -- Perform an Orderly System Shutdown on node NODE01 . . . Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2-17 2.1.15 Completing the Installation Procedure When the installation is complete, a message similar to the following text is displayed: Installation of DWMW_xxxU3 V1.2 completed at 08:37 VMSINSTAL procedure done at 08:37 These messages indicate that the installation procedure completed successfully. If you install DECwindows Motif on an Alpha system, two additional messages similar to the following are displayed: Adding history entry in VMI$ROOT:[SYSUPD]VMSINSTAL.HISTORY Creating installation data file: VMI$ROOT:[SYSUPD]DWMW_AXPU3012.VMI_DATA On Alpha systems, the file VMI$ROOT:[SYSUPD]VMSINSTAL.HISTORY contains an entry for each product that you installed using the VMSINSTAL procedure. This entry contains the following information: o Product name o Product version o Installation date o Installation status o Whether an IVP is available o Node name on which the product is installed o Installer's name The other file that is created on an Alpha system-in this example VMI$ROOT:[SYSUPD]DWMW_AXPU3012.VMI_DATA-contains the following installation data: o Names of the files that are created, deleted, modified, or renamed o Names of the accounts that are created or modified Your system automatically shuts down if AUTOGEN runs; you must then reboot your system. See the upgrade and installation supplement for your Alpha or VAX processor for instructions on how to reboot your system. 2-18 Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS ________________________ Note ________________________ If you upgrade your system with a higher version of OpenVMS at a later time, you might need to reinstall the DECwindows Motif software. ______________________________________________________ 2.2 Recovering from Errors Errors can occur during the installation if any of the following conditions exist: o The OpenVMS operating system version is incorrect. o The necessary quotas are insufficient. o The system parameter values are insufficient. o The OpenVMS help library is currently in use. o The product license is not registered and loaded. For descriptions of the error messages generated by these conditions, see the documents listed in the Associated Documents section in the Preface. These documents may help you diagnose errors and decide which corrective actions to take. 2.3 Accessing the Release Notes During the installation, the VMSINSTAL procedure copies the DECwindows Motif V1.2-3 for OpenVMS Language Variants Release Notes to the SYS$HELP:DWMW_xxxU3012.RELEASE_NOTES file. Once you return to DCL level, you can print this file on a line printer or display it at a terminal. Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2-19 3 _________________________________________________________________ After Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS This chapter discusses the tasks that you need to perform after the DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software installation is complete. Perform the following tasks after installing the DECwindows Motif software: o Start DECwindows Motif software. o Run the Installation Verification Procedure (IVP). o Choose an alternative console. If your system does not have a valid DW-MOTIF license installed, appropriate messages are displayed on your console terminal and DECwindows Motif is not automatically started. If this happens, log in to the system, install the valid license, and start DECwindows Motif software. For complete information on installing licenses using LMF, see the OpenVMS License Management Utility Manual. 3.1 Starting the DECwindows Motif Software The DECwindows Motif software can be started only if your system parameters are correct. Proceed to one of the following sections if your system parameters are correct: o Standalone systems-Section 3.1.1 o VMScluster systems-Section 3.1.2 If your system parameters are not correct, then use one of the following methods to adjust them accordingly: o Manually invoke AUTOGEN: $ @SYS$UPDATE:AUTOGEN GETDATA REBOOT CHECK_FEEDBACK Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 3-1 o Attempt to start the DECwindows Motif software. The DECwindows Motif startup procedure checks your system parameters and, if they are too low, prompts you with the following question: Some SYSGEN parameters must be reset for DECwindows to start. If you type YES, AUTOGEN will change these parameters and reboot your system. If you type NO, AUTOGEN will not run or cause a reboot, but DECwindows will not start. To run AUTOGEN at a later date, enter the following command: $ @SYS$UPDATE:AUTOGEN getdata reboot check_feedback Do you want the system to run AUTOGEN for you [YES]? After the system is rebooted and the startup is complete, the Start Session dialog box is displayed. The DECwindows Motif software is now installed and running on your system. Run the IVP as described in Section 3.2 to verify that the installation of DECwindows Motif is complete and accurate. 3.1.1 Standalone Systems Perform one of the following to start your DECwindows Motif software on a standalone system: o If your system is not running DECwindows Motif, then start DECwindows Motif with the following command: $ @SYS$MANAGER:DECW$STARTUP o If your system is currently running DECwindows Motif, then restart DECwindows Motif with the following command: $ @SYS$MANAGER:DECW$STARTUP RESTART ________________________ Note ________________________ If your system has a workstation display, then the command to restart DECwindows Motif will end your current session. The Start Session dialog box is displayed on your terminal, and you must log back in to continue using DECwindows Motif. ______________________________________________________ 3-2 After Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS The DECwindows Motif software is now installed and running on your system. Run the IVP as described in Section 3.2 to verify that the installation of DECwindows Motif is complete and accurate. 3.1.2 VMScluster Systems Starting DECwindows Motif V1.2-3 for OpenVMS on nonsatellite and satellite nodes are described in the following sections. 3.1.2.1 Starting Nonsatellite and Boot Nodes To start DECwindows Motif V1.2-3 for OpenVMS software on each of the nonsatellite nodes within your VMScluster, perform one of the following procedures: o If your system is not running DECwindows Motif, then start DECwindows Motif with the following command: $ @SYS$MANAGER:DECW$STARTUP o If your system is currently running DECwindows Motif, then restart DECwindows Motif with the following command: $ @SYS$MANAGER:DECW$STARTUP RESTART ________________________ Note ________________________ If the nonsatellite node or boot node has a workstation display, then the command to restart DECwindows Motif will end your current session. The Start Session dialog box will appear on your terminal, and you must log back in to continue using DECwindows Motif. ______________________________________________________ The DECwindows Motif software is now installed and running on your system. Run the IVP as described in Section 3.2 to verify that the installation of DECwindows Motif is complete and accurate. Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 3-3 3.1.2.2 Starting Satellite Nodes To start the DECwindows Motif software that is installed on the boot node, perform one of the following steps on each satellite node in the VMScluster that will run DECwindows Motif V1.2-3 for OpenVMS: o If the node is not running DECwindows Motif, then start DECwindows Motif with the following command: $ @SYS$MANAGER:DECW$STARTUP o If the node is currently running DECwindows Motif, then restart DECwindows Motif with the following command: $ @SYS$MANAGER:DECW$STARTUP RESTART Once DECwindows Motif has been started or restarted on each node in the VMScluster, then the installation is considered complete. You should now run the IVP as described in Section 3.2. 3.2 Running the IVP Run the Installation Verification Procedure (IVP), SYS$TEST:DECW$IVP.COM, after you install and start DECwindows Motif. This procedure contains four tests, which verify that the software installation is complete and accurate. First, the IVP attempts to run two display-oriented tests. When you invoke the IVP, it identifies the type of machine you are using. If you are using a workstation, you are asked where the display-oriented tests should be displayed. Your current workstation is the default. If you are not using a workstation, the procedure prompts you for a display name. Press Ctrl/Z at the prompt if you do not want to run the display-oriented tests. The IVP runs these tests only if the images exist on the system. If the IVP does not find the images, a message is displayed to inform you that the tests will not be run. ________________________ Note ________________________ If you are invoking the IVP from a LAT Xterminal using LAT software, enter the following command first: 3-4 After Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS $ SET DISPLAY/CREATE/NODE=LAT_nnnnnnnnnnnn/TRANSPORT=LAT Substitute your actual LAT terminal number for nnnnnnnnnn. At the _Display: prompt, enter the default. ______________________________________________________ Next, the IVP runs two nondisplay-oriented tests. The first of these tests invokes the Motif UIL compiler. If you did not install programming support, the IVP informs you that this test will not be run because the Motif UIL image does not exist. If this test runs, you are notified of its completion status. The last test converts a text file to DDIF format and then converts it back to text, comparing the original text file with the result. If the files match, the test is successful. You are notified of its completion status. Example 3-1 shows you how to run the IVP. Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 3-5 Example 3-1 Sample IVP $ @SYS$TEST:DECW$IVP Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. DECwindows Motif for OpenVMS Installation Verification Procedure (IVP) This IVP is intended to test some of the functionality of DECwindows Motif for OpenVMS and to provide a quick method of verifying the installation. This machine is not a workstation. Please provide the nodename of a workstation on which to display the IVP tests. You must be sure that this account and node have security access to the display node, or the IVP will fail. To skip the display-oriented tests, press Ctrl/Z at the following prompt. _Display: NODE33::0.0 %DECW-I-IVP, The IVP will display on NODE33::0.0 %DECW-I-IVP, Running DECW$EXAMPLES:ICO.EXE for up to a minute. %DECW-I-IVP, Press Ctrl/Y to interrupt test. %DCL-S-SPAWNED, process DECW$IVP_ICO spawned %DECW-I-IVP, Running SYS$SYSTEM:DECW$CLOCK for up to a minute. %DECW-I-IVP, Press Ctrl/Y to interrupt test. %DCL-S-SPAWNED, process DECW$IVP_CLOCK spawned %DECW-I-IVP, Invoking the UIL Motif compiler... %DECW-S-IVP, The UIL Motif compiler test completed successfully. %DECW-I-IVP, Beginning CONVERT/DOCUMENT IVP... %DECW-S-IVP, CONVERT/DOCUMENT IVP passed. %DECW-S-IVP, The IVP has completed. $ 3.3 Choosing an Alternative Console The DECwindows Motif software allows you to boot all configurations from the main console. You can then toggle between displaying and not displaying the operator window by pressing Ctrl/F2. The main console is always a workstation screen. For an alternative console, you can use a terminal connected to the workstation by means of a terminal port. If you boot from the main console, the alternative console is connected when you invoke the DECwindows Motif startup command procedure. 3-6 After Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4 _________________________________________________________________ Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS This chapter contains information about managing the performance of the DECwindows Motif V1.2-3 for OpenVMS language variants. It also describes how to use the DECW$MOTIF_TAILOR utility to remove DECwindows Motif files from the system disk. See Managing DECwindows Motif for OpenVMS Systems for additional system management information. The following topics are discussed in this chapter: o Customizing your system o Using the DECW$MOTIF_TAILOR utility o Adding DECwindows Motif base-support files o Determining and reporting problems After you install the DECwindows Motif product, you can tune your system to enhance performance or decrease the use of some system resources. For information about tuning your system, see Managing DECwindows Motif for OpenVMS Systems. 4.1 Customizing the DECwindows X11 Display Server Startup Procedure The DECwindows X11 display server manages the graphics devices on your workstation, such as the display, keyboard, and mouse. ________________________ Note ________________________ Start the DECwindows X11 display server on workstation systems only. ______________________________________________________ Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4-1 The startup command procedures automatically determine most of the configuration parameters for the DECwindows X11 display server. However, the command procedures cannot determine some items, such as the following: o Whether you have a 75-dpi or 100-dpi monitor o Whether you have a North American keyboard layout (such as for an LK201-AA or -LA or an LK401-AA or -LA keyboard) o Whether the DECwindows X11 display server uses only DECnet for OpenVMS software and local transports o Whether the DECwindows X11 display server logs both successful and unsuccessful connect and disconnect messages to the DECW$SERVER_n_ERROR.LOG file To ensure that the DECwindows X11 display server is set up correctly, modify the server startup file as follows: 1. Make a copy of the file SYS$MANAGER:DECW$PRIVATE_ SERVER_SETUP.TEMPLATE and rename it to SYS$MANAGER:DECW$PRIVATE_SERVER_SETUP.COM. This server startup file shows how to customize individual workstations by adding a section of DCL commands for each workstation. You can add setup options in either of two sections in the server startup file. Setup options added to the "Cluster Common or Standalone Workstation Setup" section affect all nodes in a cluster. Setup options added to the "Cluster Member Workstation-Specific Setup" section affect only individual nodes. If you add a workstation- specific option, you must also update the variable node_ list. 2. If your screen supports 100 dots-per-inch, add the following line: $ DECW$SERVER_DENSITY == "100" Add this line to the section for each workstation that has a 100 dots-per-inch monitor, or add it to the common section for all workstations (if all the workstations have 100-dpi monitors). 4-2 Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 3. If you want the server to log successful connect and disconnect messages, add the following line: $ DECW$SERVER_CONNECT_LOG == "TRUE" 4. Add the following line to the section for monochrome GPX workstations: $ DECW$COLOR == "FALSE" No modification is necessary for grayscale (intensity) screens. 5. Add the following line to the section for workstations with keyboards that are not North American LK201 models: $ DECW$DEFAULT_KEYMAP == "xxxxx" In the previous line, replace xxxxx with the correct DECwindows keymap name. You can determine the correct name from the model number of your LK201 or LK401 keyboard. Turn the keyboard upside down, and look for a label that specifies the model number. The model number is in a format similar to LK201-xx or LK401-xx. The model number may also be listed as LK201 or LK401. In this case, the xx that you need is in another part of the label where there is a number that looks similar to the following: nn-nnnnn-xx Use the xx part of this number to choose a keymap name from Table 4-1. Choose the keymap ending in _DP for data-processing keyboard layout and the keymap ending in _TW for typewriter layout. Table 4-1 is arranged according to the dialect for which each keyboard is designed. Table 4-1 contains the keymaps installed with the DECwindows Motif Worldwide support 1.2-3 kit. Additional keyboards are available after installing Motif 1.2-3 language variants. After you choose a keymap name, modify the DECwindows X11 display server startup file. For example, to change the keyboard layout to a Dutch typewriter layout, add the following line to the DECwindows X11 display server startup file: Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4-3 $ DECW$DEFAULT_KEYBOARD_MAP == "DUTCH_LK201LH_TW" Add a line similar to this for each workstation that does not have a North American keyboard layout or add the line to the common section for all workstations (if all the workstations use the same keyboard layout). 6. Restart DECwindows on the workstations for which you customized the server startup by using the following command: $ @SYS$MANAGER:DECW$STARTUP RESTART Table_4-1_DECwindows_Keymap_for_West_Europe_languages____________ Dialect_________Model_____________DECwindows_Keymap______________ Austrian/German LK201- AUSTRIAN_GERMAN_LK201LG_DP (AG,LG,BG,MG) AUSTRIAN_GERMAN_LK201LG_TW LK201-(NG,PG) AUSTRIAN_GERMAN_LK201NG_DP AUSTRIAN_GERMAN_LK201NG_TW LK401-(AG) AUSTRIAN_GERMAN_LK401AG_TW Belgian/French LK201- BELGIAN_FRENCH_LK201LP_DP (AP,LP,BP,MP) BELGIAN_FRENCH_LK201LP_TW Belgian/French LK401-(AP) BELGIAN_FRENCH_LK401AP_DP BELGIAN_FRENCH_LK401AP_TW British LK201- BRITISH_LK201LE_DP (AE,LE,BE,ME) BRITISH_LK201LE_TW British LK401-(AA,PA) BRITISH_LK401AA_DP BRITISH_LK401AA_TW Canadian/French LK201- CANADIAN_FRENCH_LK201LC_DP (AC,LC,BC,MC) CANADIAN_FRENCH_LK201LC_TW Canadian/French LK401- CANADIAN_FRENCH_LK401AC_DP (AC,LC,BC,MC) (continued on next page) 4-4 Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Table_4-1_(Cont.)_DECwindows_Keymap_for_West_Europe_languages____ Dialect_________Model_____________DECwindows_Keymap______________ CANADIAN_FRENCH_LK401AC_TW Danish LK201- DANISH_LK201LD_DP (AD,LD,BD,MD) DANISH_LK201LD_TW LK201-(ED,RD,FD) DANISH_LK201RD_DP DANISH_LK201RD_TW Danish LK401- DANISH_LK401AD_DP (AD,LD,BD,MD) DANISH_LK401AD_TW Dutch LK201- DUTCH_LK201LH_DP (AH,LH,BH,MH) DUTCH_LK201LH_TW LK201-(NH,PH) DUTCH_LK201NH LK401-(NH,PH) DUTCH_LK401AH Finnish LK201- FINNISH_LK201LF_DP (AF,LF,BF,MF) FINNISH_LK201LF_TW LK201-(NX,PX) FINNISH_LK201NX_DP FINNISH_LK201NX_TW Finnish LK401- FINNISH_LK401AF_DP (AF,LF,BF,MF) FINNISH_LK401AF_TW Flemish LK201- FLEMISH_LK201LB_DP (AB,LB,BB,MB) FLEMISH_LK201LB_TW Flemish LK401- FLEMISH_LK401AB_DP (AB,LB,BB,MB) FLEMISH_LK401AB_TW Icelandic LK201- ICELANDIC_LK201LU_DP (AU,LU,BU,MU) ICELANDIC_LK201LU_TW (continued on next page) Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4-5 Table_4-1_(Cont.)_DECwindows_Keymap_for_West_Europe_languages____ Dialect_________Model_____________DECwindows_Keymap______________ Italian LK201- ITALIAN_LK201LI_DP (AI,LI,BI,MI) ITALIAN_LK201LI_TW Italian LK401- ITALIAN_LK401AI_DP (AI,LI,BI,MI) ITALIAN_LK401AI_TW North American LK201- NORTH_AMERICAN_LK201LA (AA,LA,BA,MA) North American LK401- NORTH_AMERICAN_LK401AA (AA,LA,BA,MA) Norwegian LK201- NORWEGIAN_LK201LN_DP (AN,LN,BN,MN) NORWEGIAN_LK201LN_TW LK201-(EN,RN,FN) NORWEGIAN_LK201RN_DP NORWEGIAN_LK201RN_TW Norwegian LK401- NORWEGIAN_LK401AN_DP (AN,LN,BN,MN) NORWEGIAN_LK401AN_TW Portuguese LK201- PORTUGUESE_LK201LV (AV,LV,BV,MV) Portuguese LK401- PORTUGUESE_LK401AV (AV,LV,BV,MV) Spanish LK201- SPANISH_LK201LS_DP (AS,LS,BS,MS) SPANISH_LK201LS_TW Spanish LK401- SPANISH_LK401AS_DP (AS,LS,BS,MS) SPANISH_LK401AS_TW Swedish LK201- SWEDISH_LK201LM_DP (AM,LM,BM,MM) SWEDISH_LK201LM_TW (continued on next page) 4-6 Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Table_4-1_(Cont.)_DECwindows_Keymap_for_West_Europe_languages____ Dialect_________Model_____________DECwindows_Keymap______________ LK201-(NM,PM) SWEDISH_LK201NM_DP SWEDISH_LK201NM_TW Swedish LK401- SWEDISH_LK401AM_DP (AM,LM,BM,MM) SWEDISH_LK401AM_TW Swiss/French LK201- SWISS_FRENCH_LK201LK_DP (AK,LK,BK,MK) SWISS_FRENCH_LK201LK_TW Swiss/French LK401- SWISS_FRENCH_LK401AK_DP (AK,LK,BK,MK) SWISS_FRENCH_LK401AK_TW Swiss/German LK201- SWISS_GERMAN_LK201LL_DP (AL,LL,BL,ML) SWISS_GERMAN_LK201LL_TW Swiss/German LK401- SWISS_GERMAN_LK401AL_DP (AL,LL,BL,ML) SWISS_GERMAN_LK401AL_TW Combined US/UK LK201-(EE,RE,PE) UK_LK201RE US_LK201RE Combined US/UK LK401-(EE,RE,PE) UK_LK401AA __________________________________US_LK401AA_____________________ 4.2 Using the DECW$MOTIF_TAILOR Utility Use the DECW$MOTIF_TAILOR and DECW$I18NTAILOR utilities to remove some or all DECwindows Motif files from the system disk. For example, if you are not planning to use the DECwindows Motif programming support, you can remove those files. Later, if you decide you want DECwindows Motif programming support, you can add the files to the system disk by reinstalling DECwindows Motif. ________________________ Note ________________________ In order to tailor OFF DECwindows Motif files, you must use the DECW$I18NTAILOR utility BEFORE using the Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4-7 DECW$MOTIF_TAILOR. The DECW$I18NTAILOR will tailor off the internationalization files provided with the DECwindows Motif worldwide support 1.2-3. It will also tailor off language specific variants installed on top of the worldwide support. Please refer to Section 6.3 for the instructions for use of the DECW$I18NTAILOR utility. ______________________________________________________ The DECW$MOTIF_TAILOR process has two phases: 1. The first phase lists each class of DECwindows Motif files and asks whether you want to delete the class from the system disk. 2. The second phase deletes the files you indicated from the system disk. Table 4-2 lists the classes (or groups) and subclasses of DECwindows Motif files that you can delete using DECW$MOTIF_TAILOR. For a list of DECwindows Motif files and their functions, see Appendix B. Table 4-2 Classes of OpenVMS Files That Can Be Removed with __________the_DECW$MOTIF_TAILOR_Utility____________________ Class__________Subclass_______Description__________________ DECwindows No subclasses DECwindows Motif run-time Motif run- in this support. time support tailor class DECwindows No subclasses DECwindows Motif CDA support. Motif CDA in this support tailor class DECwindows DECwindows The DECwindows Motif Motif Motif applications files provide applications computer- a variety of applications. files based instruction (CBI) (continued on next page) 4-8 Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Table 4-2 (Cont.) Classes of OpenVMS Files That Can Be Removed with the DECW$MOTIF_TAILOR __________________Utility__________________________________ Class__________Subclass_______Description__________________ DECwindows No subclasses DECwindows Motif C Motif C in this programming support files programming tailor class are needed only to develop support files applications and are not required to run DECwindows Motif applications. These files are provided for programming in the C language using conventions and standards developed at the Massachusetts Institute of Technology (MIT). Fortran files No subclasses Fortran support files are in this provided for this programming tailor class language. The files are needed only to develop applications and are not required to run DECwindows Motif applications. Pascal files No subclasses Pascal support files are in this provided for this programming tailor class language. The files are needed only to develop applications and are not required to run DECwindows Motif applications. DECwindows No subclasses DECwindows Motif example Motif example in this files. files tailor class Sound files No subclasses Sound-editor support files. in this tailor class (continued on next page) Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4-9 Table 4-2 (Cont.) Classes of OpenVMS Files That Can Be Removed with the DECW$MOTIF_TAILOR __________________Utility__________________________________ Class__________Subclass_______Description__________________ Alpha No subclasses Translated-image support. translated- in this image support tailor class files______________________________________________________ 4.2.1 Removing DECwindows Motif Files from the System Disk To remove DECwindows Motif files from the system disk, do the following: 1. Log in to the SYSTEM account. 2. Enter the following command: $ RUN SYS$UPDATE:DECW$MOTIF_TAILOR After a brief overview, the DECW$MOTIF_TAILOR program lists each group, or class, of files and its size in blocks. Files are grouped according to their function. For example, all the files required for OpenVMS DECwindows device support are in one class. A file class is made up of many small subclasses. You can eliminate an entire class of files, or you can eliminate one or more of its subclasses. For example: CLASS - VMS DECwindows Motif applications files Size of entire class (with subclasses): 18009 Size of common files required for any subclass: 16988 Do you wish to select the entire class (default = NO)? Do you wish to select any of its subclasses (default = NO)? . . . 3. Decide which file classes or subclasses you do not need to support your system. DECW$MOTIF_TAILOR displays step-by-step instructions. Follow these instructions to specify which of the classes or subclasses you want to remove. 4-10 Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4. DECW$MOTIF_TAILOR deletes the files you select and displays the names of those files. _______________________ Caution _______________________ To cancel DECW$MOTIF_TAILOR during the first phase, press Ctrl/C, Ctrl/Y, or Ctrl/Z. If you cancel DECW$MOTIF_TAILOR during the second phase, a partially tailored disk may result. For a description of both phases, see Section 4.2. ______________________________________________________ Example 4-1 shows how to use DECW$MOTIF_TAILOR to remove files from a system disk. Example 4-1 Sample DECW$MOTIF_TAILOR Session $ RUN SYS$UPDATE:DECW$MOTIF_TAILOR . . . TAILOR-OFF ---------- You will now be prompted with a list of the classes and subclasses of DECwindows files that are optional. The size of each class and subclass is included in the list. This will help you decide whether or not you want to remove a class or subclass from your system. Under some classes there is a set of common files that is required in order for any subclasses to work. These files will only be deleted if you remove the ENTIRE class. If you choose to keep any subclass, this set of files is not deleted. NOTE: The files associated with selected classes and subclasses will be removed from your system. Total size of the system disk is 409792 blocks. Total space used on the system disk is 260839 blocks. Total space left on the system disk is 148953 blocks. (continued on next page) Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4-11 Example 4-1 (Cont.) Sample DECW$MOTIF_TAILOR Session CLASS - VMS DECwindows Runtime Support Size of entire class (with subclasses): 45085 No subclasses in this tailor class. Do you wish to select the entire class (default = NO)? CLASS - VMS DECwindows CDA Support Size of entire class (with subclasses): 5055 No subclasses in this tailor class. Do you wish to select the entire class (default = NO)? YES CLASS - VMS DECwindows Motif applications files Size of entire class (with subclasses): 18009 Size of common files required for any subclass: 16988 Do you wish to select the entire class (default = NO)? Do you wish to select any of its subclasses (default = NO)? YES Select the subclasses that you wish to delete: SUBCLASS - VMS DECwindows Motif computer-based instruction files (1021 blocks) [NO]: YES CLASS - DECwindows C programming support files Size of entire class (with subclasses): 6687 No subclasses in this tailor class. Do you wish to select the entire class (default = NO)? CLASS - DECwindows FORTRAN programming support files Size of entire class (with subclasses): 2429 No subclasses in this tailor class. Do you wish to select the entire class (default = NO)? CLASS - DECwindows Pascal programming support files Size of entire class (with subclasses): 3010 No subclasses in this tailor class. Do you wish to select the entire class (default = NO)? CLASS - DECwindows Motif example files Size of entire class (with subclasses): 12108 No subclasses in this tailor class. Do you wish to select the entire class (default = NO)? CLASS - Sound editor support files Size of entire class (with subclasses): 1836 Size of common files required for any subclass: 1573 Do you wish to select the entire class (default = NO)? YES (continued on next page) 4-12 Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Example 4-1 (Cont.) Sample DECW$MOTIF_TAILOR Session CLASS - Alpha translated image support files Size of entire class (with subclasses): 56880 No subclasses in this tailor class. Do you wish to select the entire class (default = NO)? Files have been selected Do you wish to remove all of the options selected? YES Removing files, please wait... %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[CDA$LIBRARY]DEFSTYLE.DDIF;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DDIF$CSW.UID;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DDIF$VIEW.UID;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DDIF$VIEWWGT.UID;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[SYSEXE]CDA$CONVERT.EXE;* . . . %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DECW$CALENDAR.UID;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DECW$CARDFILER.DAT;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DECW$CARDFILER.UID;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DECW$CLOCK.DAT;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DECW$CLOCK.UID;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DECW$LOGIN.DAT;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DECW$LOGIN.UID;* . . . %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[VUE$LIBRARY.SYSTEM]SOUND$PROFILE.VUE$DAT;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[VUE$LIBRARY.SYSTEM]SOUND$VUE_STARTUP.COM;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[DECW$DEFAULTS.SYSTEM]DIVA$WGT_UI.UID;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[SYSLIB]DIVA$LIB_SHR.EXE;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[SYSLIB]DIVA$WGT_SHR.EXE;* %VMSTLR-I-DELFILE, deleting file: SYS$SYSROOT:[SYSMSG]DIVA$LIB_MSG.EXE;* SHUTDOWN -- Perform an Orderly System Shutdown on node NODE33 Do you really want to shutdown node NODE33 [NO]? $ Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4-13 4.3 Adding DECwindows Base Support Files If you previously chose not to install or if you removed DECwindows software, do one of the following to add DECwindows base support files: o Reinstall the OpenVMS system, specifing that you only want the DECwindows Motif support. o Use the SYS$UPDATE:DECW$TAILOR.EXE utility. To use the first method of reinstalling the OpenVMS system, perform the following steps: 1. Follow the installation procedure as described in Section 2.1. 2. When the installation procedure asks whether you want to install the entire kit (see Section 2.1.7), enter NO. The procedure displays optional parts of the kit and asks whether you want to install each part. Enter YES for each part you want to install. 3. As noted in Section 2.1.9, all kit parts that you chose are displayed, and you are asked to verify that the choices are correct. 4. Once you verifiy the selections, the installation procedure continues. The second method is to use the SYS$UPDATE:DECW$TAILOR.EXE utility. See Section 4.3.1 for a detailed description and an example of adding DECwindows base support using the DECW$TAILOR utility. 4.3.1 Using the SYS$UPDATE:DECW$TAILOR.EXE Utility Use the DECW$TAILOR utility to add or remove some or all DECwindows base support files from the system disk. DECW$TAILOR is similar to DECW$MOTIF_TAILOR. The major difference is that the files that DECW$TAILOR adds or removes are the files that support the DECwindows display server as opposed to the DECwindows Motif application files, which DECW$MOTIF_TAILOR adds or removes. DECW$TAILOR has three phases: 1. The first phase asks whether you want to tailor your system by adding files "tailor on" or by deleting files "tailor off". 4-14 Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 2. In the second phase, if you choose the tailor on procedure, DECW$TAILOR lists each class of DECwindows files and asks whether you want to include them on the system disk. If you choose the tailor off procedure, DECW$TAILOR lists each class of DECwindows files and asks whether you want to delete them from the system disk. 3. In the third phase, DECW$TAILOR carries out your instructions. ________________________ Note ________________________ To cancel DECW$TAILOR during the first and second phases, press Ctrl/C, Ctrl/Y, or Ctrl/Z. If you cancel DECW$TAILOR during the third phase, a partially tailored disk may result. To tailor OpenVMS, run SYS$UPDATE:VMSTAILOR. ______________________________________________________ Table 4-3 lists the classes and subclasses of DECwindows Motif files that you can add or remove from your system using DECW$TAILOR. Table 4-3 Classes of Files That Can Be Added or Removed __________with_the_DECW$TAILOR_Utility_____________________ Class__________Subclass_______Description__________________ DECwindows No subclasses Includes the files necessary base support in this to run the DECwindows Motif files tailor class client and DECwindows display server. DECwindows PEX for PHIGS Includes the files necessary workstation support files to run the DECwindows display support files server; the PEX subclass includes support files for three-dimensional graphics. (continued on next page) Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4-15 Table 4-3 (Cont.) Classes of Files That Can Be Added or __________________Removed_with_the_DECW$TAILOR_Utility_____ Class__________Subclass_______Description__________________ 75-dpi video No subclasses Includes device support files font files in this for 75-dpi monitiors. tailor class 100-dpi video No subclasses Includes device support files font files in this for 100-dpi monitors. _______________tailor_class________________________________ 4.3.1.1 Adding DECwindows Files to the System Disk To add DECwindows files to the system disk, perform the following steps: 1. Log in to the SYSTEM account. 2. Enter the following command: $ RUN SYS$UPDATE:DECW$TAILOR After a brief overview, the DECW$TAILOR program lists each group, or class, of files and its size in blocks. Files are grouped according to their function. For example, all the files required for DECwindows base support are in one class. A file class is made up of many small subclasses. You can eliminate an entire class of files, or you can eliminate one or more of its subclasses. For example: CLASS - DECwindows workstation support files Size of entire class (with subclasses): 12380 Size of common files required for any subclass: 8919 Do you wish to select the entire class (default = NO)? Do you wish to select any of its subclasses (default = NO)? . . . 3. Decide which file classes or subclasses are needed to support your system. DECW$TAILOR displays step-by-step instructions. Follow these instructions to specify which of the classes or subclasses you want to add. 4-16 Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4. DECW$TAILOR creates a temporary command file and asks for the name of the device that contains the distribution media. ________________________ Note ________________________ The distribution media is the OpenVMS distribution media that contains the DECwindows save sets. ______________________________________________________ 5. DECW$TAILOR adds the files you selected and displays the names of those files. _______________________ Caution _______________________ To cancel DECW$TAILOR during the first phase, press Ctrl/C, Ctrl/Y, or Ctrl/Z. If you cancel DECW$TAILOR during the second phase, a partially tailored disk may result. ______________________________________________________ Example 4-2 shows how to use DECW$TAILOR to add files to a system disk. Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4-17 Example 4-2 Sample DECW$TAILOR Session $ RUN SYS$UPDATE:DECW$TAILOR . . . Do you want to tailor files "ON" or "OFF"? ON TAILOR-ON --------- You will now be prompted with a list of the classes and subclasses of DECwindows files that are optional. The size of each class and subclass is included in the list. This will help you decide whether or not you want to add a class or subclass to your system. Under some classes, there is a set of common files that is required in order for any subclasses to work. These files are added when you ask for either the entire class or any of its subclasses. Total size of the system disk is 1216665 blocks. Total space used on the system disk is 1121958 blocks. Total space left on the system disk is 94707 blocks. CLASS - DECwindows base support files Size of entire class (with subclasses): 3110 No subclasses in this tailor class. Do you wish to select the entire class (default = NO)? YES CLASS - DECwindows workstation support files Size of entire class (with subclasses): 12380 Size of common files required for any subclass: 8919 Do you wish to select the entire class (default = NO)? Do you wish to select any of its subclasses (default = NO)? CLASS - 75 dots/inch video font files Size of entire class (with subclasses): 4538 No subclasses in this tailor class. Do you wish to select the entire class (default = NO)? CLASS - 100 dots/inch video font files Size of entire class (with subclasses): 3693 No subclasses in this tailor class. Do you wish to select the entire class (default = NO)? Files have been selected Do you wish to add all of the options selected? YES Creating temporary command file, please wait... * Enter device containing DECwindows distribution media: . . . 4-18 Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4.4 Customizing Font Caching Parameters In those Asian countries that use multi-byte character sets, the font files are so large that they will not be fully loaded onto the DECwindows X-server. Instead the font will be loaded on demand. Therefore, a mechanism is provided in the DECwindows X-server for caching font data. There are several system logicals for tuning the font caching performance: DECW$FM_INIT_NUM_CACHE_ROWS 150 Default 20 DECW$FM_MIN_ROW_CACHE_SIZE 100 Default 20 DECW$MF_ROW_CACHE_EXTEND 10 Default 5 DECW$SERVER_WSQUOTA 2500 Default 1300 These logicals are defined in the command file DECW$STARTI18N_ .COM, where can be ZH_CN_ DECHANZI, ZH_TW_BIG5, etc. You can change these parameters to improve the font caching performance. Managing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS 4-19 5 _________________________________________________________________ Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants This chapter explains how to install the DECwindows Motif V1.2-3 for OpenVMS language variants. Read this chapter if you have previously successfully completed the installation of DECwindows Motif Worldwide Support V1.2-3 for OpenVMS. 5.1 Installation of the Japanese Language Variant 5.1.1 License PAK The license PAK required is DW-MOTIF-UI-JAPANESE. 5.1.2 Required Software The following software should be installed before installing the Japanese language variant: o For the Alpha platform: OpenVMS/Japanese Alpha Version 1.5 or higher o For the VAX platform: OpenVMS/Japanese VAX Version 5.5-2 or higher o DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software. Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-1 5.1.3 Product Name When you install the Japanese language variant, you should specify the product name: DWMA_JA_JPU3012 for Alpha and DWMV_JA_JPU3012 for VAX. 5.1.4 Disk Space Requirement The disk space required for installing the Japanese components is: ___________________________________________________________ Components____Alpha_______VAX______________________________ Base Kit 23000 20000 Keymaps 200 200 75 DPI fonts 24000 16000 100 DPI 19000 14000 fonts Translated- 14000 Not image Total disk 80200 50200 space______________________________________________________ 5.1.5 System Parameter ___________________________________________________________ System Parameter_____Alpha_______VAX______________________________ GBLPAGES 7500 800 GBLSECTIONS___35__________15_______________________________ 5-2 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5.1.6 Installation Verification Procedure The Japanese language variant provides an Installation Verification Procedure (IVP) in SYS$TEST:DECW$IVP_JA_ JP.COM. You can execute it to verify if the installation is completed successfully. Please see DECwindows Motif worldwide support for OpenVMS 1.2-3 Installation Guide for how to run an IVP. The differences between SYS$TEST:DECW$IVP_JA_JP.COM and SYS$TEST:DECW$IVP.COM are: o DECW$CLOCK is run in Japanese. o The UIL compiler is used to compile a Japanese UIL file. 5.2 Installation of the Korean language Variant 5.2.1 License PAK The license PAK required is DW-MOTIF-UI-HANGUL. 5.2.2 Required Software The following software should be installed before installing the Korean language variant: o For the Alpha platform, OpenVMS Alpha or OpenVMS/Hangul Alpha Version 1.5 or higher o For the VAX platform, OpenVMS VAX or OpenVMS/Hangul VAX Version 5.5-2 or higher o DECwindows Motif Worldwide Support V1.2-3 for OpenVMS. ________________________ Note ________________________ For full Korean support, you are recommended to install the Korean language variant running the Korean language variant on the standard OpenVMS platform, please see the release notes. ______________________________________________________ Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-3 5.2.3 Product Name When you install the Korean language variant, you should specify the product name: DWMA_KO_KRU3012 for Alpha and DWMV_KO_KRU3012 for VAX. 5.2.4 Disk Space Requirement The disk space required for installing the Korean components is: ___________________________________________________________ Component_____Alpha_______VAX______________________________ Base Kit 24000 23000 Fonts 15000 9000 Translated- 500 Not image Total disk 39500 32000 space______________________________________________________ 5.2.5 System Parameter ___________________________________________________________ System Parameter_____Alpha_______VAX______________________________ GBLPAGES 600 400 GBLSECTIONS___12__________10_______________________________ 5-4 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5.2.6 Installation Verification Procedure The Korean language variant provides an Installation Verification Procedure (IVP) in SYS$TEST:DECW$IVP_KO_ KR.COM. You can execute it to verify if the installation is completed successfully. Please see DECwindows Motif worldwide support for OpenVMS 1.2-3 Installation Guide for how to run an IVP. The differences between SYS$TEST:DECW$IVP.COM and SYS$TEST:DECW$IVP_KO_KR.COM are: o DECW$CLOCK is run in Korean. o The UIL compiler is used to compile a Korean UIL file. Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-5 5.3 Installation of the Simplified Chinese language Variant 5.3.1 License PAK The license PAK required is DW-MOTIF-UI-HANZI. 5.3.2 Required Software The following software should be installed before installing the simplified Chinese language variant: o For the Alpha platform: OpenVMS Alpha OpenVMS/Hanzi Alpha Version 1.5 or higher o For the VAX platform: OpenVMS VAX or OpenVMS/Hanzi VAX Version 5.5-2 or higher o DECwindows Motif worldwide support for OpenVMS 1.2-3 ________________________ Note ________________________ For full simplified Chinese support, you are recommended to install the simplified Chinese language variant on OpenVMS/Hanzi. For the limitations of running the simplified Chinese language variant on the standard OpenVMS platform, please see the release notes. ______________________________________________________ 5.3.3 Product Name When you install the simplified Chinese language variant, you should specify the product name: DWMA_ZH_CNU3012 for Alpha and DWMV_ZH_CNU3012 for VAX. 5-6 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5.3.4 Disk Space Requirement The disk space required for installing the simplified Chinese components is: ___________________________________________________________ Component_____Alpha_______VAX______________________________ Base Kit 23000 22000 Fonts 34000 15000 Translated- 500 Not image Total disk 57500 37000 space______________________________________________________ 5.3.5 System Parameter ___________________________________________________________ System Parameter_____Alpha_______VAX______________________________ GBLPAGES 600 400 GBLSECTIONS___12__________10_______________________________ 5.3.6 Production Key Registration (VAX only) The installation procedure will prompt you for entering a production key for registration. You should apply the key before the installation. If you fail to enter a correct production key, the following message will be displayed: Production Key Registration Procedure Error. Do you want to continue? [N] If you choose Yes to continue, the installation procedure will complete successfully. However, some components will be disabled and will not be working for simplified Chinese processing. Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-7 5.3.7 Installation Verification Procedure The simplified Chinese language variant provides an Installation Verification Procedure (IVP) in SYS$TEST:DECW$IVP_ZH_CN.COM. You can execute it to verify if the installation is completed successfully. Please see DECwindows Motif worldwide support for OpenVMS 1.2-3 Installation Guide for how to run an IVP. The differences between SYS$TEST:DECW$IVP.COM and SYS$TEST:DECW$IVP_ZH_CN.COM are: o DECW$CLOCK is run in simplified Chinese. o The UIL compiler is used to compile a simplified Chinese UIL file. 5.4 Installation of the Thai language Variant 5.4.1 License PAK The license PAK required is DW-MOTIF-UI-THAI. 5.4.2 Required Software The following software should be installed before installing the Thai language variant: o For the Alpha platform: OpenVMS Alpha or OpenVMS/Thai Alpha Version 1.5 or higher o For the VAX platform: OpenVMS VAX or OpenVMS/Thai VAX Version 5.5-2 or higher o DECwindows Motif Worldwide Support V1.2-3 for OpenVMS ________________________ Note ________________________ For full Thai support, you are recommended to install the Thai language variant on OpenVMS/Thai. For the limitations of running the Thai language variant on the standard OpenVMS platform, please see the release notes. ______________________________________________________ 5-8 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5.4.3 Product Name When you install the Thai language variant, you should specify the product name: DWMA_TH_THU3012 for Alpha and DWMV_TH_THU3012 for VAX. 5.4.4 Disk Space Requirement The disk space required for installing the Thai components is: ___________________________________________________________ Component_____Alpha_______VAX______________________________ Base Kit 8000 7000 Keymaps 200 200 75dpi Fonts 6000 2000 100dpi Fonts 6500 2200 Display 7000 7000 PostScript Total disk 27700 18400 space______________________________________________________ 5.4.5 System Parameter ___________________________________________________________ System Parameter_____Alpha_______VAX______________________________ GBLPAGES 2000 400 GBLSECTIONS___12__________10_______________________________ Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-9 5.4.6 Installation Verification Procedure The Thai language variant provides an Installation Verification Procedure (IVP) in SYS$TEST:DECW$IVP_TH_ TH.COM. You can execute it to verify if the installation is completed successfully. Please see DECwindows Motif worldwide support for OpenVMS 1.2-3 Installation Guide for how to run an IVP. The differences between SYS$TEST:DECW$IVP_TH_TH.COM and SYS$TEST:DECW$IVP.COM are: 5-10 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants o DECW$CLOCK is run in Thai. o The UIL compiler is used to compile a Thai UIL file. 5.5 Installation of the Traditional Chinese language Variant 5.5.1 License PAK The license PAK required is DW-MOTIF-UI-HANYU 5.5.2 Required Software The following software should be installed before installing the traditional Chinese language variant: o For the Alpha platform: OpenVMS Alpha or OpenVMS/Hanyu Alpha Version 1.5 or higher o For the VAX platform: OpenVMS VAX or OpenVMS/Hanyu VAX Version 5.5-2 or higher o DECwindows Motif Worldwide Support V1.2-3 for OpenVMS ________________________ Note ________________________ For full traditional Chinese support, you are recommended to install the traditional Chinese language variant on OpenVMS/Hanyu. For the limitations of running the traditional Chinese language variant on the standard OpenVMS platform, please see the release notes. ______________________________________________________ 5.5.3 Product Name When you install the traditional Chinese language variant, you should specify the product name: DWMA_ZH_TWU3012 for Alpha and DWMV_ZH_TWU3012 for VAX. the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-11 5.5.4 Disk Space Requirement The disk space required for installing traditional Chinese components is: ___________________________________________________________ Component_____Alpha_______VAX______________________________ Base Kit 41500 40500 Fonts 32000 18000 Translated- 1100 Not image Total disk 74600 58500 space______________________________________________________ 5.5.5 System Parameter ___________________________________________________________ System Parameter_____Alpha_______VAX______________________________ GBLPAGES 1200 500 GBLSECTIONS___12__________10_______________________________ 5.5.6 Installation Verification Procedure The traditional Chinese language variants provides an Installation Verification Procedure (IVP) in SYS$TEST:DECW$IVP_ZH_TW.COM. You can execute it to verify if the installation is completed successfully. Please see DECwindows Motif for OpenVMS DECwindows Motif worldwide support for OpenVMS 1.2-3 run an IVP. The differences between SYS$TEST:DECW$IVP_ZH_TW.COM and SYS$TEST:DECW$IVP.COM are: o DECW$CLOCK is run in traditional Chinese o The UIL compiler is used to compile a traditional Chinese UIL file. 5-12 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5.6 Installation of the Czech language variant 5.6.1 License PAK The license PAK required is DW-MOTIF-UI-CESKY. 5.6.2 Required software The following software should be installed before installing the Czech language variant: o For the Alpha platform: OpenVMS Alpha Version 1.5 or higher, DECwindows Motif Worldwide Support for OpenVMS/Alpha V1.2-3. o For the VAX platform: OpenVMS VAX Version 5.5-2 or higher, DECwindows Motif Worldwide Support for OpenVMS/VAX V1.2-3. 5.6.3 Product Name When installing the Czech language variant, you should specify the product name DECWMCS_CZU3012 for both Alpha and VAX installation. 5.6.4 Disk Space Requirements The disk space required for installing the Czech language variant is: the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-13 ___________________________________________________________ Components____________Alpha_______VAX______________________ Czech language 18000 17000 support ISO Latin fonts 36000 21000 Total_disk_space______54000_______38000____________________ 5.6.5 Installation Account Quotas VMSINSTAL requires the installation account to have a minimum of the following quotas: ASTLM = 24 BIOLM = 18 BYTLM = 18,000 DIOLM = 18 ENQLM = 30 FILLM = 20 5.6.6 Installation Verification Procedure An Installation verification procedure (IVP) can be run at the installation time by answering YES to the appropriate installation question. If you want to run the IVP separately, to ensure the integrity of your DECwindows Motif language variant at exploitation time, enter the following command: $ MCR SYS$TEST:DECW$I18N_IVP CS_CZ 5.6.7 Editing the startup files and restarting DECwindows Motif environment All language variants existing on the system will be started automatically when restarting DECwindows. For more information about editing the startup files and restarting DECwindows Motif configuration see Section 6.1. 5-14 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5.6.8 Amending the LIBRARY.DECW$BOOKSHELF file The language variant installation provides a new library bookshelf file called DECW$BOOK:LIBRARY.DECW$BOOKSHELF. If you want to keep your existing library bookshelf file, save it to another name before starting the language variant installation and restore it back after the end of installation, especially if you plan to declare to purge files during the installation. For example, before starting the installation do the following: $ COPY DECW$BOOK:LIBRARY.DECW$BOOKSHELF DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED After the end of the installation, restore your original LIBRARY.DECW$BOOKSHELF back: $ COPY DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED DECW$BOOK:LIBRARY.DECW$BOOKSHELF If you want to include a translated version of Getting Started with DECwindows Motif online book to your existing library bookshelf file, append the line found in DECW$BOOK:LIBRARY.DECW$BOOKSHELF to the copy of your original DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED, before you copy it back to DECW$BOOK:LIBRARY.DECW$BOOKSHELF. 5.7 Installation of the Slovak Language Variant 5.7.1 License PAK The license PAK required is DW-MOTIF-UI-SLOVENSKY. the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-15 5.7.2 Required software The following software should be installed before installing the Slovak language variant: o For the Alpha platform: OpenVMS Alpha Version 1.5 or higher, DECwindows Motif Worldwide Support for OpenVMS/Alpha V1.2-3. o For the VAX platform: OpenVMS VAX Version 5.5-2 or higher, DECwindows Motif Worldwide Support for OpenVMS/VAX V1.2-3. 5.7.3 Product Name When installing the Slovak language variant, you should specify the product name DECWMSK_SKU3012 for both Alpha and VAX installation. 5.7.4 Disk Space Requirements The disk space required for installing the Slovak language variant is: ___________________________________________________________ Components____________Alpha_______VAX______________________ Slovak language 18000 17000 support ISO Latin fonts 36000 21000 Total_disk_space______54000_______38000____________________ 5.7.5 Installation Account Quotas VMSINSTAL requires the installation account to have a minimum of the following quotas: ASTLM = 24 BIOLM = 18 BYTLM = 18,000 DIOLM = 18 ENQLM = 30 5-16 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants FILLM = 20 5.7.6 Installation Verification Procedure An Installation verification procedure (IVP) can be run at the installation time by answering YES to the appropriate installation question. If you want to run the IVP separately, to ensure the integrity of your DECwindows Motif language variant at exploitation time, enter the following command: $ MCR SYS$TEST:DECW$I18N_IVP SK_SK 5.7.7 Editing the startup files and restarting DECwindows Motif environment All language variants existing on the system will be started automatically when restarting DECwindows. For more information about editing the startup files and restarting DECwindows Motif configuration see Section 6.1. 5.7.8 Amending the LIBRARY.DECW$BOOKSHELF file The language variant installation provides a new library bookshelf file called DECW$BOOK:LIBRARY.DECW$BOOKSHELF. If you want to keep your existing library bookshelf file, save it to another name before starting the language variant installation and restore it back after the end of installation, especially if you plan to declare to purge files during the installation. For example, before starting the installation do the following: $ COPY DECW$BOOK:LIBRARY.DECW$BOOKSHELF DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED After the end of the installation, restore your original LIBRARY.DECW$BOOKSHELF back: $ COPY DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED DECW$BOOK:LIBRARY.DECW$BOOKSHELF the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-17 If you want to include a translated version of the Getting Started with DECwindows Motif online book to your existing library bookshelf file, append the line found in DECW$BOOK:LIBRARY.DECW$BOOKSHELF to the copy of your original DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED, before you copy it back to DECW$BOOK:LIBRARY.DECW$BOOKSHELF. 5.8 Installation of the Russian Language Variant 5.8.1 License PAK The license PAK required is DW-MOTIF-UI-RUSSKIJ. 5.8.2 Required software The following software should be installed before installing the Russian language variant: o For the Alpha platform: OpenVMS Alpha Version 1.5 or higher, DECwindows Motif Worldwide Support for OpenVMS/Alpha V1.2-3. o For the VAX platform: OpenVMS VAX Version 5.5-2 or higher, DECwindows Motif Worldwide Support for OpenVMS/VAX V1.2-3. 5.8.3 Product Name When installing the Russian language variant, you should specify the product name DECWMRU_RUU3012 for both Alpha and VAX installation. 5-18 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5.8.4 Disk Space Requirements The disk space required for installing the Russian language variant is: ___________________________________________________________ Components____________Alpha_______VAX______________________ Russian language 18000 17000 support ISO Latin fonts 36000 21000 Total_disk_space______54000_______38000____________________ 5.8.5 Installation Account Quotas VMSINSTAL requires the installation account to have a minimum of the following quotas: ASTLM = 24 BIOLM = 18 BYTLM = 18,000 DIOLM = 18 ENQLM = 30 FILLM = 20 5.8.6 Installation Verification Procedure An Installation verification procedure (IVP) can be run at the installation time by answering YES to the appropriate installation question. If you want to run the IVP separately, to ensure the integrity of your DECwindows Motif language variant at exploitation time, enter the following command: $ MCR SYS$TEST:DECW$I18N_IVP RU_RU the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-19 5.8.7 Editing the startup files and restarting DECwindows Motif environment All language variants existing on the system will be started automatically when restarting DECwindows. For more information about editing the startup files and restarting DECwindows Motif configuration see Section 6.1. 5.8.8 Amending the LIBRARY.DECW$BOOKSHELF file The language variant installation provides a new library bookshelf file called DECW$BOOK:LIBRARY.DECW$BOOKSHELF. If you want to keep your existing library bookshelf file, save it to another name before starting the language variant installation and restore it back after the end of installation, especially if you plan to declare to purge files during the installation. For example, before starting the installation do the following: $ COPY DECW$BOOK:LIBRARY.DECW$BOOKSHELF DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED After the end of the installation, restore your original LIBRARY.DECW$BOOKSHELF back: $ COPY DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED DECW$BOOK:LIBRARY.DECW$BOOKSHELF If you want to include a translated version of Getting Started with DECwindows Motif online book to your existing library bookshelf file, append the line found in DECW$BOOK:LIBRARY.DECW$BOOKSHELF to the copy of your original DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED, before you copy it back to DECW$BOOK:LIBRARY.DECW$BOOKSHELF. 5-20 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5.9 Installation of the Hungarian Language Variant 5.9.1 License PAK The license PAK required is DW-MOTIF-UI-MAGYAR. 5.9.2 Required software The following software should be installed before installing the Hungarian language variant: o For the Alpha platform: OpenVMS Alpha Version 1.5 or higher, DECwindows Motif Worldwide Support for OpenVMS/Alpha V1.2-3. o For the VAX platform: OpenVMS VAX Version 5.5-2 or higher, DECwindows Motif Worldwide Support for OpenVMS/VAX V1.2-3. 5.9.3 Product Name When installing the Hungarian language variant, you should specify the product name DECWMHU_HUU3012 for both Alpha and VAX installation. 5.9.4 Disk Space Requirements The disk space required for installing the Hungarian language variant is: ___________________________________________________________ Components____________Alpha_______VAX______________________ Hungarian language 18000 17000 support ISO Latin fonts 36000 21000 Total_disk_space______54000_______38000____________________ the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-21 5.9.5 Installation Account Quotas VMSINSTAL requires the installation account to have a minimum of the following quotas: ASTLM = 24 BIOLM = 18 BYTLM = 18,000 DIOLM = 18 ENQLM = 30 FILLM = 20 5.9.6 Installation Verification Procedure An Installation verification procedure (IVP) can be run at the installation time by answering YES to the appropriate installation question. If you want to run the IVP separately, to ensure the integrity of your DECwindows Motif language variant at exploitation time, enter the following command: $ MCR SYS$TEST:DECW$I18N_IVP HU_HU 5.9.7 Editing the startup files and restarting DECwindows Motif environment All language variants existing on the system will be started automatically when restarting DECwindows. For more information about editing the startup files and restarting DECwindows Motif configuration see Section 6.1. 5.9.8 Amending the LIBRARY.DECW$BOOKSHELF file The language variant installation provides a new library bookshelf file called DECW$BOOK:LIBRARY.DECW$BOOKSHELF. If you want to keep your existing library bookshelf file, save it to another name before starting the language variant installation and restore it back after the end of installation, especially if you plan to declare to purge files during the installation. 5-22 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants For example, before starting the installation do the following: $ COPY DECW$BOOK:LIBRARY.DECW$BOOKSHELF DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED After the end of the installation, restore your original LIBRARY.DECW$BOOKSHELF back: $ COPY DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED DECW$BOOK:LIBRARY.DECW$BOOKSHELF If you want to include a translated version of Getting Started with DECwindows Motif online book to your existing library bookshelf file, append the line found in DECW$BOOK:LIBRARY.DECW$BOOKSHELF to the copy of your original DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED, before you copy it back to DECW$BOOK:LIBRARY.DECW$BOOKSHELF. the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-23 5.10 Installation of the Polish Language Variant 5.10.1 License PAK The license PAK required is DW-MOTIF-UI-POLSKI. 5.10.2 Required software The following software should be installed before installing the Polish language variant: o For the Alpha platform: OpenVMS Alpha Version 1.5 or higher, DECwindows Motif Worldwide Support for OpenVMS/Alpha V1.2-3. o For the VAX platform: OpenVMS VAX Version 5.5-2 or higher, DECwindows Motif Worldwide Support for OpenVMS/VAX V1.2-3. 5.10.3 Product Name When installing the Polish language variant, you should specify the product name DECWMPL_PLU3012 for both Alpha and VAX installation. 5.10.4 Disk Space Requirements The disk space required for installing the Polish language variant is: ___________________________________________________________ Components____________Alpha_______VAX______________________ Polish language 18000 17000 support ISO Latin fonts 36000 21000 Total_disk_space______54000_______38000____________________ 5-24 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5.10.5 Installation Account Quotas VMSINSTAL requires the installation account to have a minimum of the following quotas: ASTLM = 24 BIOLM = 18 BYTLM = 18,000 DIOLM = 18 ENQLM = 30 FILLM = 20 5.10.6 Installation Verification Procedure An Installation verification procedure (IVP) can be run at the installation time by answering YES to the appropriate installation question. If you want to run the IVP separately, to ensure the integrity of your DECwindows Motif language variant at exploitation time, enter the following command: $ MCR SYS$TEST:DECW$I18N_IVP PL_PL 5.10.7 Editing the startup files and restarting DECwindows Motif environment All language variants existing on the system will be started automatically when restarting DECwindows. For more information about editing the startup files and restarting DECwindows Motif configuration see Section 6.1. 5.10.8 Amending the LIBRARY.DECW$BOOKSHELF file The language variant installation provides a new library bookshelf file called DECW$BOOK:LIBRARY.DECW$BOOKSHELF. If you want to keep your existing library bookshelf file, save it to another name before starting the language variant installation and restore it back after the end of installation, especially if you plan to declare to purge files during the installation. the DECwindows Motif V1.2-3 for OpenVMS Language Variants 5-25 For example, before starting the installation do the following: $ COPY DECW$BOOK:LIBRARY.DECW$BOOKSHELF DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED After the end of the installation, restore your original LIBRARY.DECW$BOOKSHELF back: $ COPY DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED DECW$BOOK:LIBRARY.DECW$BOOKSHELF If you want to include a translated version of Getting Started with DECwindows Motif online book to your existing library bookshelf file, append the line found in DECW$BOOK:LIBRARY.DECW$BOOKSHELF to the copy of your original DECW$BOOK:LIBRARY.DECW$BOOKSHELF_SAVED, before you copy it back to DECW$BOOK:LIBRARY.DECW$BOOKSHELF. 5-26 Installing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 6 _________________________________________________________________ Managing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 6.1 Customizing Language Variables When DECwindows Motif language variant starts up, a procedure DECW$DEFINE_LANG.COM will be called if it exists. This command procedure will define the LANG and XNL$LANG logicals for a certain locale. When you install a language variant kit, DECW$DEFINE_LANG.COM will be provided for that language and replace the previous one, if any. Therefore, if you install multiple language variant kits, the LANG and XNL$LANG will be defined according to the last installed locale. If you want to change these logicals, you can edit and modify the command file SYS$MANAGER:DECW$DEFINE_LANG.COM. 6.2 Customizing Motif Window Manager Fontlist When a language variant kit is installed, the fontlist for that language will be appended to the Motif Window Manager system resource file DECW$MWM.DAT located at SYS$COMMON:[DECW$DEFAULTS.SYSTEM] such that the window and icon titles can be displayed in local language. Tailoring off the language variant will remove the fontlist. If you want to change the fontlist, you can modify DECW$MWM.DAT. Managing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 6-1 6.3 Using the DECW$I18NTAILOR Utility You can use the DECW$I18NTAILOR utility to remove the language variant and the DECwindows Motif Worldwide Support files from your system disk. ________________________ Note ________________________ You have to tailor off all language variants before you tailor off the Worldwide Support base kit. ______________________________________________________ To remove (tailor off) DECwindows Motif worldwide support components from the system disk, do the following: 6-2 Managing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 1. Log in to the SYSTEM account. 2. Enter the following command: $ @SYS$MANAGER:DECW$I18NTAILOR The command procedure will ask you whether you want to tailor off or exit the procedure. Enter Off and follow the instructions given by the procedure step-by-step as in the following example. ________________________ Note ________________________ DECW$I18NTAILOR: This command procedure is used to either tailor on optional savesets or tailor off savesets for I18N/LV DECwindows Motif VAX V1.2-3. ______________________________________________________ $ @SYS$MANAGER:DECW$I18NTAILOR Tailor Off/Exit [Exit]: off Tailor-off You may only tailor off LV kit one by one and the I18N can only be tailor-off if all LV kit are gone. Moreover, you can only tailor off the entire kit. You have installed the following LV kit(s): HANZI kit Please specify the name of the LV kit: hanzi The following parts of DECwindows Motif /HANZI will be... 3. DECW$I18NTAILOR deletes the files, creates the font directory again and removes the language variant fontlist from DECW$MWM.DAT. 4. After all language variant kits have been tailored off, you can tailor off the I18N files by the same procedure. DECW$I18NTAILOR will display the following message: You have only installed the I18N kit. Do you want to tailor off the I18N kit? [N]: y After you tailor off the I18N files, you should tailor off DECwindows Motif base files using the DECW$MOTIF_TAILOR utility. < head1>(Determining and Reporting Problems\problems) Managing the DECwindows Motif V1.2-3 for OpenVMS Language Variants 6-3 If you encounter a problem while using DECwindows Motif language variants, review the Software Product Description (SPD) for an explanation of the warranty. If you encounter a problem during the warranty period, use the following methods to report the problem or follow alternate instructions provided by Digital for reporting problems: o Call Digital if your software contract or warranty agreement includes telephone support. o Submit a Software Performance Report (SPR). o If you discover a problem with or have comments about the documentation, fill out and submit a Reader's Comments form, located at the back of each DECwindows Motif V1.2-3 for OpenVMS manual. 6-4 Managing the DECwindows Motif V1.2-3 for OpenVMS Language Variants A _________________________________________________________________ Sample Installation This appendix contains a sample Product Authorization Key (PAK) registration and a product installation. A.1 Sample Product Authorization Key Registration Example A-1 contains a sample registration of a DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software PAK. Example A-1 Sample Product Authorization Key Registration $ @SYS$UPDATE:VMSLICENSE.COM VMS License Management Utility Options: 1. REGISTER a Product Authorization Key 2. AMEND an existing Product Authorization Key 3. CANCEL an existing Product Authorization Key 4. LIST the Product Authorization Keys 5. MODIFY an existing Product Authorization Key 6. DISABLE an existing Product Authorization Key 7. DELETE an existing Product Authorization Key 8. COPY an existing Product Authorization Key 9. MOVE an existing Product Authorization Key 10. ENABLE an existing Product Authorization Key 11. SHOW the licenses loaded on this node 12. SHOW the unit requirements for this node 99. EXIT this procedure Type '?' at any prompt for a description of the information requested. Press Ctrl/Z at any prompt to exit this procedure. Enter one of the above choices [1] Do you have your Product Authorization Key? [YES] (continued on next page) Sample Installation A-1 Example A-1 (Cont.) Sample Product Authorization Key Registration The REGISTER option allows you add a new license to a license database. A Product Authorization Key (PAK) provides the product name and information you need to register the license. You must enter all the information provided by your PAK exactly as specified. PAK ID: Issuer [DEC] Authorization Number [] LAB030419 PRODUCT ID: Product Name [] DW-MOTIF Producer [DEC] NUMBER OF UNITS: Number of Units [] 400 KEY LEVEL: Version [] PRODUCT RELEASE DATE: [] KEY TERMINATION DATE: Key Termination Date [] RATING: Availability Table Code [] H Activity Table Code [] MISCELLANEOUS: Key Options [] Product Token [] Hardware-Id [] Checksum [] 2-fbic-odnh-enwj-lled (continued on next page) A-2 Sample Installation Example A-1 (Cont.) Sample Product Authorization Key Registration License Database File: SYS$COMMON:[SYSEXE]LMF$LICENSE.LDB Issuer: DEC Authorization: LAB030419 Producer: DEC Product Name: DW-MOTIF Units: 400 Date: Version: Termination Date: Availability: H Activity: Options: Token: Hardware ID: Checksum: 2-FBIC-ODNH-ENWJ-LLED Is this information correct? [YES] Registering DW-MOTIF license in SYS$COMMON:[SYSEXE]LMF$LICENSE.LDB... Do you want to LOAD this license on this system? [YES] %LICENSE-I-LOADED, DEC DW-MOTIF was successfully loaded with 400 units VMS License Management Utility Options: 1. REGISTER a Product Authorization Key 2. AMEND an existing Product Authorization Key 3. CANCEL an existing Product Authorization Key 4. LIST the Product Authorization Keys 5. MODIFY an existing Product Authorization Key 6. DISABLE an existing Product Authorization Key 7. DELETE an existing Product Authorization Key 8. COPY an existing Product Authorization Key 9. MOVE an existing Product Authorization Key 10. ENABLE an existing Product Authorization Key 11. SHOW the licenses loaded on this node 12. SHOW the unit requirements for this node 99. EXIT this procedure (continued on next page) Sample Installation A-3 Example A-1 (Cont.) Sample Product Authorization Key Registration Type '?' at any prompt for a description of the information requested. Press Ctrl/Z at any prompt to exit this procedure. Enter one of the above choices [1] 99 $ A.2 Sample Installation Example A-2 contains a sample installation of the DECwindows Motif Worldwide Support V1.2-3 for OpenVMS software on the OpenVMS Alpha operating system. The sample installation assumes that no users are logged in to the system and that you specified OPTIONS N to display the release notes. Example A-2 Sample Installation OpenVMS Alpha Software Product Installation Procedure It is 3-JUNE-1995 at 09:22. Enter a question mark (?) at any time for help. * Are you satisfied with the backup of your system disk [YES]? The following products will be processed: DWMW_AXPU3 V1.2 Beginning installation of DWMW_AXPU3 V1.2 at 09:22 %VMSINSTAL-I-RESTORE, Restoring product save set A ... Release notes included with this kit are always copied to SYS$HELP. Additional Release Notes Options: (continued on next page) A-4 Sample Installation Example A-2 (Cont.) Sample Installation 1. Display release notes 2. Print release notes 3. Both 1 and 2 4. None of the above * Select option [2]: * Do you want to continue the installation [NO]? Yes %VMSINSTAL-I-RELMOVED, Product's release notes have been moved to SYS$HELP. *** Installing DECwindows Motif Worldwide Support V1.2-3 for OpenVMS Alpha software *** Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to and embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. You can install the DECwindows Motif kit completely or in selected portions. A complete installation requires as many as 209,000 blocks. If you choose to perform a partial installation, you can select (tailor) the programming support files that support your DECwindows Motif application development. Whether you perform a complete or partial installation, this kit provides support for running DECwindows Motif applications on OpenVMS compute servers. * Do you want to install the entire kit [Y]? No This installation procedure provides support files for developing DECwindows Motif applications in several programming languages. These files are needed only to develop applications and are not required to run DECwindows Motif applications. The free disk space requirement for each programming support file ranges from 3000 to 8000 blocks. * Do you want to install DECwindows Motif programming support [Y]? (continued on next page) Sample Installation A-5 Example A-2 (Cont.) Sample Installation Support files are supplied for the following OpenVMS programming languages: Fortran, Pascal In addition, support files are supplied for programming in the C language using conventions and standards developed at the Massachusetts Institute of Technology. * Do you want to install all programming language support files [Y]? No Do you want support files provided for each of the following programming languages? Type Yes or No for each language. * Fortran [N]? Yes * Pascal [N]? Yes * MIT-compatible C [N]? Yes * Do you want to install DECwindows Motif programming examples [Y]? This installation procedure provides support files for running your DECwindows Motif V1.2-3 for OpenVMS VAX applications on OpenVMS Alpha systems using the DECmigrate product. These files support applications developed for the OSF/Motif Release 1.1.3 toolkit. These files are not required to run DECwindows Motif V1.2-3 for OpenVMS Alpha applications. The free disk space requirement for these support files is approximately 53,000 blocks. * Do you want to install DECwindows Motif V1.2-3 for OpenVMS Alpha * translated image support [Y]? You have selected the following portions of the kit: o DECwindows Motif Applications and Run-time Libraries o DECwindows Motif V1.2-3 for OpenVMS Alpha translated image support o DECwindows Motif programming examples o DECwindows Motif programming support Fortran, Pascal MIT C language programming conventions * Are these selections correct [Y]? (continued on next page) A-6 Sample Installation Example A-2 (Cont.) Sample Installation A registered and loaded product authorization key for DW_MOTIF is required to run any DECwindows Motif V1.2-3 for OpenVMS application. If you answer NO to the next question, the installation of DECwindows Motif V1.2-3 for OpenVMS will be terminated. Product: DW-MOTIF Producer: DEC Version: Release Date: * Does this product have an authorization key registered and loaded? Yes DECwindows Motif will not start if your system parameters are not correct. o If you allow a system shutdown, the installation procedure will reboot the system at the end of the installation. If your system parameters are incorrect, the installation will run AUTOGEN prior to the system reboot. o If you do not allow a system shutdown, the installation procedure will continue, and you will be informed at the end of the installation whether you need to modify your system parameters in order to start DECwindows Motif. To complete the installation of this product, you should reboot the system. If it is not convenient to reboot at this time, then enter NO to the following question. If you enter NO, the installation procedure will continue. * Will you allow a system reboot after this product is installed [YES]? No No further questions will be asked. (continued on next page) Sample Installation A-7 Example A-2 (Cont.) Sample Installation %VMSINSTAL-I-RESTORE, Restoring product save set B ... %VMSINSTAL-I-RESTORE, Restoring product save set C ... %VMSINSTAL-I-RESTORE, Restoring product save set D ... %VMSINSTAL-I-RESTORE, Restoring product save set E ... %VMSINSTAL-I-RESTORE, Restoring product save set J ... %VMSINSTAL-I-RESTORE, Restoring product save set L ... %VMSINSTAL-I-RESTORE, Restoring product save set N ... %VMSINSTAL-I-RESTORE, Restoring product save set P ... %VMSINSTAL-I-RESTORE, Restoring product save set Q ... %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... Final stage of installation is in process. %VMSINSTAL-I-RESTORE, Restoring product save set S ... This product creates system directory VMI$ROOT:[SYSUPD.DECWMII18N123] %VMSINSTAL-I-RESTORE, Restoring product save set T ... %VMSINSTAL-I-RESTORE, Restoring product save set U ... %VMSINSTAL-I-RESTORE, Restoring product save set V ... %VMSINSTAL-I-RESTORE, Restoring product save set W ... %VMSINSTAL-I-RESTORE, Restoring product save set X ... %VMSINSTAL-I-RESTORE, Restoring product save set Y ... %VMSINSTAL-I-RESTORE, Restoring product save set Z ... The Installation Verification Procedure (IVP) should be run after the installation has been completed and DECwindows Motif has been restarted. The IVP can be found in SYS$TEST:DECW$IVP.COM. The installation procedure has determined that your system parameters are set correctly and that it will not be necessary to run AUTOGEN or reboot the system. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $ @SYS$MANAGER:DECW$STARTUP RESTART If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $ @SYS$MANAGER:DECW$STARTUP * * * N O T E * * * (continued on next page) A-8 Sample Installation Example A-2 (Cont.) Sample Installation If you are installing DECwindows Motif from your workstation console, log off after you enter the command to start DECwindows Motif. Installation of DWMW_AXPU3 V1.2 completed at 09:38 Adding history entry in VMI$ROOT:[SYSUPD]VMSINSTAL.HISTORY Creating installation data file: VMI$ROOT:[SYSUPD]DWMW_AXP012.VMI_DATA VMSINSTAL procedure done at 09:41 Sample Installation A-9 B _________________________________________________________________ DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation B.1 Sample Installation of the Japanese Language Variant Example B-1 Sample Installation of the Japanese Language Variant $ @sys$update:vmsinstal OpenVMS VAX Software Product Installation Procedure V6.1 It is 13-JUN-1995 at 13:10. Enter a question mark (?) at any time for help. %VMSINSTAL-W-NOTSYSTEM, You are not logged in to the SYSTEM account. * Do you want to continue anyway [NO]? yes * Are you satisfied with the backup of your system disk [YES]? * Where will the distribution volumes be mounted: TOOLOW$DKA300:[SHAI.AMOTIF-KITS-LLVS-123.VAX.JA_JP] Enter the products to be processed from the first distribution volume set. * Products: DWMV_JA_JPU3012 * Enter installation options you wish to use (none): The following products will be processed: DWMV_JA_JPU3 V1.2 Beginning installation of DWMV_JA_JPU3 V1.2 at 13:11 (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-1 Example B-1 (Cont.) Sample Installation of the Japanese Language Variant %VMSINSTAL-I-RESTORE, Restoring product save set A ... %VMSINSTAL-I-RELMOVED, Product's release notes have been moved to SYS$HELP. Installing the DECwindows Motif/Japanese V1.2-3 for OpenVMS VAX Software Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. A registered and loaded product authorization key for DW-MOTIF-UI-JAPANESE is required to run any DECwindows Motif/Japanese for OpenVMS application. If you answer NO to the next question, the installation of DECwindows Motif for OpenVMS will be terminated. Product: DW-MOTIF-UI-JAPANESE Producer: DEC Version: Release Date: * Does this product have an authorization key registered and loaded? yes The free disk requirement for installing Japanese keymap is about 200 blocks * Do you need to install Japanese keymaps [Y]? The free disk requirement for installing 75DPI Japanese fonts is about 16000 blocks * Do you need to install 75dpi Japanese font [Y]? The free disk requirement for installing 100DPI Japanese fonts is about 14000 blocks * Do you need to install 100dpi Japanese font [Y]? The following parts of the kit will be installed. (continued on next page) B-2 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-1 (Cont.) Sample Installation of the Japanese Language Variant CDA support Applications Motif Examples JAPANESE keymaps 75dpi JAPANESE font 100dpi JAPANESE font * Is this correct [Y]? No further questions will be asked. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSUP D.DECWMI18N123.JAPANESE]. %VMSINSTAL-I-RESTORE, Restoring product save set B ... %VMSINSTAL-I-RESTORE, Restoring product save set C ... %VMSINSTAL-I-RESTORE, Restoring product save set D ... %VMSINSTAL-I-RESTORE, Restoring product save set E ... %VMSINSTAL-I-RESTORE, Restoring product save set F ... %VMSINSTAL-I-RESTORE, Restoring product save set G ... %VMSINSTAL-I-RESTORE, Restoring product save set H ... ============================================================== Checking files in specific directories Please delete/modify those files in order to function properly ============================================================== (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-3 Example B-1 (Cont.) Sample Installation of the Japanese Language Variant %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... %COPY-S-COPIED, TALTAL$DKA300:[SYS0.SYSUPD.DWMV_JA_JPU3012]JA_JP.LOCALE;1 copied to VMI$ROOT:[SYSUPD.DECWMI18N123.JAPANESE]JA_JP.LOCALE;1 (1437 blocks) %COPY-S-COPIED, TALTAL$DKA300:[SYS0.SYSUPD.DWMV_JA_JPU3012]EN_US.LOCALE;1 copied to VMI$ROOT:[SYSUPD.DECWMI18N123.JAPANESE]EN_US.LOCALE;1 (27 blocks) 668 fonts loaded Creating sys$common:[sysfont.decw.75dpi]DECW$FONT_DIRECTORY.DAT 628 fonts loaded Creating sys$common:[sysfont.decw.100dpi]DECW$FONT_DIRECTORY.DAT The following fontlist is appended to decw$system_defaults:decw$mwm.dat: -*-Kmenu-Medium-R-Normal--*-120-*-*-P-*-JISX0201.1976-0=JISX0201.1976-0,\ -*-Gothic-Medium-R-Normal--*-120-*-*-M-*-JISX0208.1983-1=JISX0208.1983-1,\ -*-Gothic-Medium-R-Normal--*-120-*-*-M-*-JISX0208.1983-1=JISX0208-? %PURGE-I-FILPURG, VMI$ROOT:[DECW$DEFAULTS.SYSTEM]DECW$MWM.DAT;18 deleted (18 blocks) lang logical has been defined as ja_JP please edit sys$manager:decw$define_lang.com if you want to change the logical to another locale. Then run decw$define_lang again The Installation Verification Procedure (IVP) should be run after the installation has been completed and DECwindows Motif has been restarted. The IVP can be found in SYS$TEST:DECW$IVP_JA_JP.COM Installation of DECwindows Motif/Japanese for OpenVMS VAX V1.2-3 is now complete. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP RESTART If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP Installation of DWMV_JA_JPU3 V1.2 completed at 13:20 Enter the products to be processed from the next distribution volume set. * Products: Exit VMSINSTAL procedure done at 13:24 (continued on next page) B-4 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-1 (Cont.) Sample Installation of the Japanese Language Variant Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-5 B.2 Sample Installation of the Korean Language Variant Example B-2 Sample Installation of the Korean Language Variant $ @sys$update:vmsinstal OpenVMS Alpha Software Product Installation Procedure V6.2 It is 19-JUN-1995 at 10:42. Enter a question mark (?) at any time for help. %VMSINSTAL-W-NOTSYSTEM, You are not logged in to the SYSTEM account. * Do you want to continue anyway [NO]? yes * Are you satisfied with the backup of your system disk [YES]? * Where will the distribution volumes be mounted: TOOLOW$DKA300:[SHAI.AMOTIF-KITS-LLVS-123.AXP.KO_KR] Enter the products to be processed from the first distribution volume set. * Products: DWMA_KO_KRU3012 * Enter installation options you wish to use (none): The following products will be processed: DWMA_KO_KRU3 V1.2 Beginning installation of DWMA_KO_KRU3 V1.2 at 10:42 %VMSINSTAL-I-RESTORE, Restoring product save set A ... Installing the DECwindows Motif/Hangul for OpenVMS Alpha V1.2-3 Software Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. (continued on next page) B-6 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-2 (Cont.) Sample Installation of the Korean Language Variant A registered and loaded product authorization key for DW-MOTIF-UI-HANGUL is required to run any DECwindows Motif/Hangul for OpenVMS application. If you answer NO to the next question, the installation of DECwindows Motif for OpenVMS will be terminated. Product: DW-MOTIF-UI-HANGUL Producer: DEC Version: Release Date: * Does this product have an authorization key registered and loaded? yes The free disk requirement for installing Hangul fonts is about 15000 blocks * Do you need to install Hangul font [Y]? This installation procedure provides support files for running your DECwindows Motif/Hangul OpenVMS VAX applications on OpenVMS Alpha systems using the DECmigrate product. These files support applications developed for the OSF/Motif Release 1.1.3 toolkit. These files are not required to run DECwindows Motif/Hangul OpenVMS Alpha applications. The free disk space requirement for these support files is approximately 350 blocks. * Do you need to install Hangul translated-image support [Y]? The following parts of the kit will be installed. Run-Time Libraries CDA support Applications Motif Examples HANGUL font Korean Motif 1.1.3 Translated Images * Is this correct [Y]? No further questions will be asked. (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-7 Example B-2 (Cont.) Sample Installation of the Korean Language Variant %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$ DEFAULTS.SYSTEM.KO_KR_DECKOREAN]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$ DEFAULTS.USER.KO_KR_DECKOREAN]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$L IBRARY.SYSTEM.KO_KR_DECKOREAN]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$L IBRARY.USER.KO_KR_DECKOREAN]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHL P.KO_KR_DECKOREAN]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHL P.EXAMPLES.DECW.KO_KR_DECKOREAN]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSLI B.KO_KR_DECKOREAN]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSMS G.KO_KR_DECKOREAN]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[CDA$L IBRARY.KO_KR_DECKOREAN]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSUP D.DECWMI18N123.HANGUL]. %VMSINSTAL-I-RESTORE, Restoring product save set B ... %VMSINSTAL-I-RESTORE, Restoring product save set C ... %VMSINSTAL-I-RESTORE, Restoring product save set D ... %VMSINSTAL-I-RESTORE, Restoring product save set E ... %VMSINSTAL-I-RESTORE, Restoring product save set F ... %VMSINSTAL-I-RESTORE, Restoring product save set G ... ============================================================== Checking files in specific directories Please delete/modify those files in order to function properly ============================================================== (continued on next page) B-8 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-2 (Cont.) Sample Installation of the Korean Language Variant %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... The following fontlist is appended to decw$system_defaults:decw$mwm.dat: -*-screen-medium-r-normal--*-180-*-*-m-*-ksc5601.1987-1=KSC5601.1987-1 %PURGE-I-FILPURG, SYS$COMMON:[DECW$DEFAULTS.SYSTEM]DECW$MWM.DAT;6 deleted (18 blocks) %PURGE-I-FILPURG, VMI$ROOT:[SYSFONT.DECW.75DPI]DECW$FONT_ALIAS.DAT;1 deleted (39 blocks) %PURGE-I-FILPURG, VMI$ROOT:[SYSFONT.DECW.100DPI]DECW$FONT_ALIAS_100DPI.DAT;1 deleted (42 blocks) lang logical has been defined as ko_KR.deckorean please edit sys$manager:decw$define_lang.com if you want to change the logical to another locale. Then run decw$define_lang again DECwindows Motif/Hangul for OpenVMS The Installation Verification Procedure (IVP) should be run after the installation has been completed and DECwindows Motif has been restarted. The IVP can be found in SYS$TEST:DECW$IVP_KO_KR.COM Installation of DECwindows Motif/Hangul for OpenVMS Alpha V1.2-3 is now complete. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP RESTART If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP Installation of DWMA_KO_KRU3 V1.2 completed at 10:45 Adding history entry in VMI$ROOT:[SYSUPD]VMSINSTAL.HISTORY Creating installation data file: VMI$ROOT:[SYSUPD]DWMA_KO_KRU3012.VMI_DATA Enter the products to be processed from the next distribution volume set. * Products: Exit VMSINSTAL procedure done at 10:48 Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-9 B.3 Sample Installation of the Thai Language Variant Example B-3 Sample Installation of the Thai Language Variant $ @sys$update:vmsinstal OpenVMS Alpha Software Product Installation Procedure V6.2 It is 19-JUN-1995 at 10:58. Enter a question mark (?) at any time for help. %VMSINSTAL-W-NOTSYSTEM, You are not logged in to the SYSTEM account. * Do you want to continue anyway [NO]? yes * Are you satisfied with the backup of your system disk [YES]? * Where will the distribution volumes be mounted: TOOLOW$DKA300:[SHAI.AMOTIF-KITS-LLVS-123.AXP.TH_TH] Enter the products to be processed from the first distribution volume set. * Products: DWMA_TH_THU3012 * Enter installation options you wish to use (none): The following products will be processed: DWMA_TH_THU3 V1.2 Beginning installation of DWMA_TH_THU3 V1.2 at 10:58 %VMSINSTAL-I-RESTORE, Restoring product save set A ... Installing the DECwindows Motif/Thai for OpenVMS Alpha V1.2-3 Software Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. (continued on next page) B-10 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-3 (Cont.) Sample Installation of the Thai Language Variant A registered and loaded product authorization key for DW-MOTIF-UI-THAI is required to run any DECwindows Motif/Thai for OpenVMS application. If you answer NO to the next question, the installation of DECwindows Motif for OpenVMS will be terminated. Product: DW-MOTIF-UI-THAI Producer: DEC Version: Release Date: * Does this product have an authorization key registered and loaded? yes The free disk requirement for installing Thai keymaps is about 200 blocks * Do you need to install Thai keymaps [Y]? The free disk requirement for installing 75DPI Thai fonts is about 6000 blocks * Do you need to install 75DPI Thai fonts [Y]? The free disk requirement for installing 100DPI Thai fonts is about 6500 blocks * Do you need to install 100DPI Thai fonts [Y]? The free disk requirement for installing Thai outline fonts is about 7000 blocks ** Do you need to install Thai outline fonts [Y]? The following parts of the kit will be installed. Run-Time Libraries CDA support Applications Motif Examples Thai keymap files 75DPI Thai fonts 100DPI Thai fonts Thai outline fonts * Is this correct [Y]? No further questions will be asked. (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-11 Example B-3 (Cont.) Sample Installation of the Thai Language Variant %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$ DEFAULTS.SYSTEM.TH_TH_TACTIS]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$ DEFAULTS.USER.TH_TH_TACTIS]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$L IBRARY.SYSTEM.TH_TH_TACTIS]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$L IBRARY.USER.TH_TH_TACTIS]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHL P.TH_TH_TACTIS]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHL P.EXAMPLES.DECW.TH_TH_TACTIS]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSLI B.TH_TH_TACTIS]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSMS G.TH_TH_TACTIS]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[CDA$L IBRARY.TH_TH_TACTIS]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSUP D.DECWMI18N123.THAI]. %VMSINSTAL-I-RESTORE, Restoring product save set B ... %VMSINSTAL-I-RESTORE, Restoring product save set C ... %VMSINSTAL-I-RESTORE, Restoring product save set D ... %VMSINSTAL-I-RESTORE, Restoring product save set E ... %VMSINSTAL-I-RESTORE, Restoring product save set F ... %VMSINSTAL-I-RESTORE, Restoring product save set G ... %VMSINSTAL-I-RESTORE, Restoring product save set H ... %VMSINSTAL-I-RESTORE, Restoring product save set I ... ============================================================== Checking files in specific directories Please delete/modify those files in order to function properly ============================================================== %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... The following fontlist is appended to decw$system_defaults:decw$mwm.dat: -*-screen-medium-r-normal--*-180-*-*-p-*-tis620.2533-1=TIS620.2533-1 %PURGE-I-FILPURG, SYS$COMMON:[DECW$DEFAULTS.SYSTEM]DECW$MWM.DAT;8 deleted (18 blocks) (continued on next page) B-12 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-3 (Cont.) Sample Installation of the Thai Language Variant lang logical has been defined as th_th.TACTIS please edit sys$manager:decw$define_lang.com if you want to change the logical to another locale. Then run decw$define_lang again DECwindows Motif/Thai for OpenVMS The Installation Verification Procedure (IVP) should be run after the installation has been completed and DECwindows Motif has been restarted. The IVP can be found in SYS$TEST:DECW$IVP_TH_TH.COM Installation of DECwindows Motif/Thai for OpenVMS Alpha V1.2-3 is now complete. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP RESTART If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP Installation of DWMA_TH_THU3 V1.2 completed at 11:09 Adding history entry in VMI$ROOT:[SYSUPD]VMSINSTAL.HISTORY Creating installation data file: VMI$ROOT:[SYSUPD]DWMA_TH_THU3012.VMI_DATA Enter the products to be processed from the next distribution volume set. Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-13 B.4 Sample Installation of the Simplified Chinese Language Variant Example B-4 Sample Installation of the Simplified Chinese Language Variant $ @sys$update:vmsinstal ************************************************************************ Can not find file: SYS$COMMON:[SYSMSG.HANZI]VMSINSTAL_LANGUAGE.COM Using: SYS$MESSAGE:VMSINSTAL_LANGUAGE.COM ************************************************************************ OpenVMS Alpha Software Product Installation Procedure V6.2 It is 19-JUN-1995 at 14:39. Enter a question mark (?) at any time for help. %VMSINSTAL-W-NOTSYSTEM, You are not logged in to the SYSTEM account. * Do you want to continue anyway [NO]? yes * Are you satisfied with the backup of your system disk [YES]? * Where will the distribution volumes be mounted: TOOLOW$DKA300:[SHAI.AMOTIF-KITS-LLVS-123.AXP.ZH_CN] Enter the products to be processed from the first distribution volume set. * Products: DWMA_ZH_CNU3012 * Enter installation options you wish to use (none): The following products will be processed: DWMA_ZH_CNU3 V1.2 Beginning installation of DWMA_ZH_CNU3 V1.2 at 14:39 %VMSINSTAL-I-RESTORE, Restoring product save set A ... Installing the DECwindows Motif/Hanzi for OpenVMS Alpha V1.2-3 Software (continued on next page) B-14 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-4 (Cont.) Sample Installation of the Simplified Chinese Language Variant Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. A registered and loaded product authorization key for DW-MOTIF-UI-HANZI is required to run any DECwindows Motif/Hanzi for OpenVMS application. If you answer NO to the next question, the installation of DECwindows Motif for OpenVMS will be terminated. Product: DW-MOTIF-UI-HANZI Producer: DEC Version: Release Date: * Does this product have an authorization key registered and loaded? yes The free disk requirement for installing Hanzi fonts is about 34000 blocks * Do you need to install Hanzi font [Y]? This installation procedure provides support files for running your DECwindows Motif/Hanzi OpenVMS VAX applications on OpenVMS Alpha systems using the DECmigrate product. These files support applications developed for the OSF/Motif Release 1.1.3 toolkit. These files are not required to run DECwindows Motif/Hanzi OpenVMS Alpha applications. The free disk space requirement for these support files is approximately 350 blocks. * Do you need to install Hanzi translated-image support [Y]? The following parts of the kit will be installed. CDA support Applications Motif Examples Hanzi fonts Hanzi translated image support (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-15 Example B-4 (Cont.) Sample Installation of the Simplified Chinese Language Variant * Is this correct [Y]? %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$ DEFAULTS.SYSTEM.ZH_CN_DECHANZI]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$ DEFAULTS.USER.ZH_CN_DECHANZI]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$L IBRARY.SYSTEM.ZH_CN_DECHANZI]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$L IBRARY.USER.ZH_CN_DECHANZI]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHL P.ZH_CN_DECHANZI]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHL P.EXAMPLES.DECW.ZH_CN_DECHANZI]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSLI B.ZH_CN_DECHANZI]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSMS G.ZH_CN_DECHANZI]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[CDA$L IBRARY.ZH_CN_DECHANZI]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSUP D.DECWMI18N123.HANZI]. No further questions will be asked. %VMSINSTAL-I-RESTORE, Restoring product save set B ... AVMS62::ENGNR 14:40:33 BACKUP CPU=00:00:06.14 PF=2331 IO=3150 MEM=176 Restoring file: AVMS62$DKA0:[SYS0.SYSUPD.DWMA_ZH_CNU3012]DECW$HANZIIM.DECW$BOOK;3 Saveset volume:1, saveset block:73 (32256 byte blocks) %VMSINSTAL-I-RESTORE, Restoring product save set C ... %VMSINSTAL-I-RESTORE, Restoring product save set D ... %VMSINSTAL-I-RESTORE, Restoring product save set E ... %VMSINSTAL-I-RESTORE, Restoring product save set F ... %VMSINSTAL-I-RESTORE, Restoring product save set G ... ============================================================== Checking files in specific directories Please delete/modify those files in order to function properly ============================================================== (continued on next page) B-16 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-4 (Cont.) Sample Installation of the Simplified Chinese Language Variant %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... The following fontlist is appended to decw$system_defaults:decw$mwm.dat: -*-screen-medium-r-normal--*-180-*-*-m-*-gb2312.1980-1=GB2312.1980-1 %PURGE-I-FILPURG, SYS$COMMON:[DECW$DEFAULTS.SYSTEM]DECW$MWM.DAT;9 deleted (18 blocks) %PURGE-I-FILPURG, SYS$COMMON:[SYSFONT.DECW.75DPI]DECW$FONT_ALIAS.DAT;4 deleted (39 blocks) %PURGE-I-FILPURG, VMI$ROOT:[SYSFONT.DECW.100DPI]DECW$FONT_ALIAS_100DPI.DAT;4 deleted (45 blocks) lang logical has been defined as zh_CN.dechanzi please edit sys$manager:decw$define_lang.com if you want to change the logical to another locale. Then run decw$define_lang again DECwindows Motif/Hanzi for OpenVMS The Installation Verification Procedure (IVP) should be run after the installation has been completed and DECwindows Motif has been restarted. The IVP can be found in SYS$TEST:DECW$IVP_ZH_CN.COM Installation of DECwindows Motif/Hanzi for OpenVMS Alpha V1.2-3 is now complete. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP RESTART If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP Installation of DWMA_ZH_CNU3 V1.2 completed at 14:44 Adding history entry in VMI$ROOT:[SYSUPD]VMSINSTAL.HISTORY Creating installation data file: VMI$ROOT:[SYSUPD]DWMA_ZH_CNU3012.VMI_DATA Enter the products to be processed from the next distribution volume set. Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-17 B.5 Sample Installation of the Traditional Chinese Language Variant Example B-5 Sample Installation of the Traditional Chinese Language Variant $ @sys$update:vmsinstal OpenVMS VAX Software Product Installation Procedure V6.0 It is 14-JUN-1995 at 15:00. Enter a question mark (?) at any time for help. %VMSINSTAL-W-NOTSYSTEM, You are not logged in to the SYSTEM account. %VMSINSTAL-W-ACTIVE, The following processes are still active: DECW$SERVER_0 DECW$MWM VUE$SALTI_4 VUE$SALTI_5 DECW$TE_00EF SALTI _FTA35: * Do you want to continue anyway [NO]? yes Are you satisfied with the backup of your system disk [YES]? * Where will the distribution volumes be mounted: TOOLOW$DKA300:[SHAI.AMOTIF-KITS-LLVS-123.VAX.ZH_TW] Enter the products to be processed from the first distribution volume set. * Products: DWMV_ZH_TWU3012 * Enter installation options you wish to use (none): The following products will be processed: DWMV_ZH_TWU3 V1.2 Beginning installation of DWMV_ZH_TWU3 V1.2 at 15:02 %VMSINSTAL-I-RESTORE, Restoring product save set A ... Installing the DECwindows Motif/Hanyu for OpenVMS VAX V1.2-3 Software (continued on next page) B-18 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-5 (Cont.) Sample Installation of the Traditional Chinese Language Variant Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. A registered and loaded product authorization key for DW-MOTIF-UI-HANYU is required to run any DECwindows Motif/Hanyu for OpenVMS application. If you answer NO to the next question, the installation of DECwindows Motif for OpenVMS will be terminated. Product: DW-MOTIF-UI-HANYU Producer: DEC Version: Release Date: * Does this product have an authorization key registered and loaded? yes The free disk requirement for installing Hanyu fonts is about 32000 blocks * Do you need to install Hanyu font [Y]? The following parts of the kit will be installed. Run-Time Libraries CDA support Applications Motif Examples HANYU font * Is this correct [Y]? No further questions will be asked. (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-19 Example B-5 (Cont.) Sample Installation of the Traditional Chinese Language Variant %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSUPD.DECWMI18N123.HANYU]. %VMSINSTAL-I-RESTORE, Restoring product save set B ... %VMSINSTAL-I-RESTORE, Restoring product save set C ... %VMSINSTAL-I-RESTORE, Restoring product save set D ... %VMSINSTAL-I-RESTORE, Restoring product save set E ... %VMSINSTAL-I-RESTORE, Restoring product save set F ... ============================================================== Checking files in specific directories Please delete/modify those files in order to function properly ============================================================== %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... The following fontlist is appended to decw$system_defaults:decw$mwm.dat: -*-screen-medium-r-normal--*-180-*-*-m-*-dec.cns11643.1986-2=DEC.CNS11643. 1986-2,\ -*-screen-medium-r-normal--*-180-*-*-m-*-dec.dtscs-1990-2=DEC.DTSCS.1990-2 %PURGE-I-FILPURG, VMI$ROOT:[DECW$DEFAULTS.SYSTEM]DECW$MWM.DAT;30 deleted (20 blocks) 286 fonts loaded Creating sys$common:[sysfont.decw.75dpi]DECW$FONT_DIRECTORY.DAT lang logical has been defined as zh_TW.dechanyu please edit sys$manager:decw$define_lang.com if you want to change the logical to another locale. Then run decw$define_lang again DECwindows Motif/Hanyu for OpenVMS The Installation Verification Procedure (IVP) should be run after the installation has been completed and DECwindows Motif has been restarted. The IVP can be found in SYS$TEST:DECW$IVP_ZH_TW.COM Installation of DECwindows Motif/Hanyu for OpenVMS VAX V1.2-3 is now complete. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP RESTART (continued on next page) B-20 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-5 (Cont.) Sample Installation of the Traditional Chinese Language Variant If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP Installation of DWMV_ZH_TWU3 V1.2 completed at 15:29 Enter the products to be processed from the next distribution volume set. * Products: Exit VMSINSTAL procedure done at 15:29 Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-21 B.6 Sample Installation of the Czech Language Variant Example B-6 Sample Installation of the Czech Language Variant $ @sys$update:vmsinstal decwmcs_czu3012 motif_path:[cs.kit.ssb] OpenVMS VAX Software Product Installation Procedure V6.1 It is 14-JUN-1995 at 18:19. Enter a question mark (?) at any time for help. % %VMSINSTAL-W-NOTSYSTEM, You are not logged in to the SYSTEM account. %VMSINSTAL-W-ACTIVE, The following processes are still active: DECW$MWM DEL DECW$TE_1034 _FTA881: DECW$FD DECW$SERVER_0 * Do you want to continue anyway [NO]? y * Are you satisfied with the backup of your system disk [YES]? The following products will be processed: decwmCS_CZU3 V1.2 Beginning installation of decwmCS_CZU3 V1.2 at 18:19 %VMSINSTAL-I-RESTORE, Restoring product save set A ... %VMSINSTAL-I-RELMOVED, Product's release notes have been moved to SYS$HELP. If one of DECwindows Motif OpenVMS UI V1.2-3 LNE1 (non-Latin1) language variants is already installed on your system, then you don't need to install LNE1 fonts. If you don't have any V1.2-3 LNE1 language variant installed, or you have any previous LNE1 language variant version installed on your system, then you MUST install LNE1 fonts. * Do you want to install LNE1 fonts [Y]? %decwmCS_CZU3-I-INTRO, Installing DECwindows Motif for OpenVMS User Interface/Cesky V1.2-3 Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. (continued on next page) B-22 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-6 (Cont.) Sample Installation of the Czech Language Variant Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to and embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. A registered and loaded product authorization key for the DECwindows Motif for OpenVMS (VAX) V1.2-3/Cesky language variant kit is required. If you answer NO to the next question, the installation of the DECwindows Motif for OpenVMS (VAX) V1.2-3/Cesky language variant kit will be aborted. Product: DW-MOTIF-UI-CESKY Producer: DEC Version: 1.2-3 Release Date: * Does this product have an authorization key registered and loaded? y * Do you want to purge files replaced by this installation [YES]? n * Do you want to run the IVP after the installation [YES]? * Enter display destination for IVP [BIKETE]: %decwmCS_CZU3-I-NOMORE, No additional questions will be asked. %decwmCS_CZU3-I-TIME, Installation will take approximately 50 minutes. %VMSINSTAL-I-RESTORE, Restoring product save set B ... %VMSINSTAL-I-RESTORE, Restoring product save set C ... %VMSINSTAL-I-RESTORE, Restoring product save set D ... %VMSINSTAL-I-RESTORE, Restoring product save set E ... 696 fonts loaded Creating decw$root:[sysfont.decw.75dpi]DECW$FONT_DIRECTORY.DAT 720 fonts loaded Creating decw$root:[sysfont.decw.100dpi]DECW$FONT_DIRECTORY.DAT If your system startup procedure contains a line similar to the following: $ @SYS$MANAGER:DECW$STARTI18N P1 P2 then delete this line. DECW$STARTI18N procedure will be automatically invoked when starting or restarting DECwindows Motif. (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-23 Example B-6 (Cont.) Sample Installation of the Czech Language Variant If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP RESTART If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... Installation of decwmCS_CZU3 V1.2 completed at 18:32 VMSINSTAL procedure done at 18:32 B-24 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation B.7 Sample Installation of the Slovak Language Variant Example B-7 Sample Installation of the Slovak Language Variant $ @sys$update:vmsinstal decwmsk_sku3012 motif_path:[sk.kit.ssb] OpenVMS VAX Software Product Installation Procedure V6.1 It is 14-JUN-1995 at 16:37. Enter a question mark (?) at any time for help. %VMSINSTAL-W-NOTSYSTEM, You are not logged in to the SYSTEM account. %VMSINSTAL-W-ACTIVE, The following processes are still active: DECW$FD DECW$SERVER_0 DECW$MWM DEL DECW$TE_0D2F _FTA848: VUE$DEL_3 VUE$DEL_4 _FTA851: * Do you want to continue anyway [NO]? y * Are you satisfied with the backup of your system disk [YES]? The following products will be processed: decwmSK_SKU3 V1.2 Beginning installation of decwmSK_SKU3 V1.2 at 16:37 %VMSINSTAL-I-RESTORE, Restoring product save set A ... %VMSINSTAL-I-RELMOVED, Product's release notes have been moved to SYS$HELP. If one of DECwindows Motif OpenVMS UI V1.2-3 LNE1 (non-Latin1) language variants is already installed on your system, then you don't need to install LNE1 fonts. If you don't have any V1.2-3 LNE1 language variant installed, or you have any previous LNE1 language variant version installed on your system, then you MUST install LNE1 fonts. * Do you want to install LNE1 fonts [Y]? n %decwmSK_SKU3-I-INTRO, Installing DECwindows Motif for OpenVMS User Interface/Slovensky V1.2. (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-25 Example B-7 (Cont.) Sample Installation of the Slovak Language Variant Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to and embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. A registered and loaded product authorization key for the DECwindows Motif for OpenVMS (VAX) V1.2-3/Slovensky language variant kit is required. If you answer NO to the next question, the installation of the DECwindows Motif for OpenVMS (VAX) V1.2-3/Slovensky language variant kit will be aborted. Product: DW-MOTIF-UI-SLOVENSKY Producer: DEC Version: 1.2-3 Release Date: * * Does this product have an authorization key registered and loaded? y * Do you want to purge files replaced by this installation [YES]? n * Do you want to run the IVP after the installation [YES]? * Enter display destination for IVP [BIKETE]: (continued on next page) B-26 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-7 (Cont.) Sample Installation of the Slovak Language Variant %decwmSK_SKU3-I-NOMORE, No additional questions will be asked. %decwmSK_SKU3-I-TIME, Installation will take approximately 5 minutes. %VMSINSTAL-I-RESTORE, Restoring product save set B ... %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[CDA$LIBRARY.SK_SK] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$DEFAULTS.SYSTEM.SK_SK] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHLP.SK_SK] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHLP.EXAMPLES.SK_SK]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSLIB.SK_SK]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSMSG.SK_SK]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$LIBRARY.SYSTEM.SK_SK]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$DEFAULTS.USER.SK_SK]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$LIBRARY.USER.SK_SK]. If your system startup procedure contains a line similar to the following: $ @SYS$MANAGER:DECW$STARTI18N P1 P2 then delete this line. DECW$STARTI18N procedure will be automatically invoked when starting or restarting DECwindows Motif. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP RESTART If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... Installation of decwmSK_SKU3 V1.2 completed at 16:40 VMSINSTAL procedure done at 16:40 (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-27 Example B-7 (Cont.) Sample Installation of the Slovak Language Variant B-28 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation B.8 Sample Installation of the Russian Language Variant Example B-8 Sample Installation of the Russian Language Variant $ @sys$update:vmsinstal decwmru_ruu3012 motif_path:[ru.kit.ssb] OpenVMS VAX Software Product Installation Procedure V6.1 It is 14-JUN-1995 at 17:39. Enter a question mark (?) at any time for help. % %VMSINSTAL-W-NOTSYSTEM, You are not logged in to the SYSTEM account. %VMSINSTAL-W-ACTIVE, The following processes are still active: DECW$FD DECW$SERVER_0 DECW$MWM DEL DECW$TE_0FCB _FTA860: * Do you want to continue anyway [NO]? y * Are you satisfied with the backup of your system disk [YES]? The following products will be processed: decwmRU_RUU3 V1.2 Beginning installation of decwmRU_RUU3 V1.2 at 17:39 %VMSINSTAL-I-RESTORE, Restoring product save set A ... %VMSINSTAL-I-RELMOVED, Product's release notes have been moved to SYS$HELP. If one of DECwindows Motif OpenVMS UI V1.2-3 LNE1 (non-Latin1) language variants is already installed on your system, then you don't need to install LNE1 fonts. If you don't have any V1.2-3 LNE1 language variant installed, or you have any previous LNE1 language variant version installed on your system, then you MUST install LNE1 fonts. * Do you want to install LNE1 fonts [Y]? %decwmRU_RUU3-I-INTRO, Installing DECwindows Motif for OpenVMS User Interface/Russkij V1.2. Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-29 Example B-8 (Cont.) Sample Installation of the Russian Language Variant Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to and embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. A registered and loaded product authorization key for the DECwindows Motif for OpenVMS (VAX) V1.2-3/Russkij language variant kit is required. If you answer NO to the next question, the installation of DECwindows Motif for OpenVMS (VAX) V1.2-3/Russkij language variant kit will be aborted. Product: DW-MOTIF-UI-RUSSKIJ Producer: DEC Version: 1.2-3 Release Date: * * Does this product have an authorization key registered and loaded? y * Do you want to purge files replaced by this installation [YES]? n * Do you want to run the IVP after the installation [YES]? * Enter display destination for IVP [BIKETE]: (continued on next page) B-30 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-8 (Cont.) Sample Installation of the Russian Language Variant %decwmRU_RUU3-I-NOMORE, No additional questions will be asked. %decwmRU_RUU3-I-TIME, Installation will take approximately 50 minutes. %VMSINSTAL-I-RESTORE, Restoring product save set B ... %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[CDA$LIBRARY.RU_RU] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$DEFAULTS.SYSTEM.RU_RU] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHLP.RU_RU] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHLP.EXAMPLES.RU_RU] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSLIB.RU_RU] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSMSG.RU_RU] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$LIBRARY.SYSTEM.RU_RU] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$DEFAULTS.USER.RU_RU] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$LIBRARY.USER.RU_RU] %VMSINSTAL-I-RESTORE, Restoring product save set C ... %VMSINSTAL-I-RESTORE, Restoring product save set D ... %VMSINSTAL-I-RESTORE, Restoring product save set E ... 696 fonts loaded Creating decw$root:[sysfont.decw.75dpi]DECW$FONT_DIRECTORY.DAT 720 fonts loaded Creating decw$root:[sysfont.decw.100dpi]DECW$FONT_DIRECTORY.DAT If your system startup procedure contains a line similar to the following: $ @SYS$MANAGER:DECW$STARTI18N P1 P2 then delete this line. DECW$STARTI18N procedure will be automatically invoked when starting or restarting DECwindows Motif. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP RESTART (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-31 Example B-8 (Cont.) Sample Installation of the Russian Language Variant If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... Installation of decwmRU_RUU3 V1.2 completed at 17:53 VMSINSTAL procedure done at 17:53 B.9 Sample Installation of the Hungarian language variant Example B-9 Sample Installation of Hungarian language variant $ @sys$update:vmsinstal decwmhu_huu3012 motif_path:[hu.kit.ssb] OpenVMS VAX Software Product Installation Procedure V6.1 It is 14-JUN-1995 at 17:24. Enter a question mark (?) at any time for help. %VMSINSTAL-W-NOTSYSTEM, You are not logged in to the SYSTEM account. %VMSINSTAL-W-ACTIVE, The following processes are still active: DECW$FD DECW$SERVER_0 DECW$MWM DEL DECW$TE_0FCB _FTA860: * Do you want to continue anyway [NO]? y * Are you satisfied with the backup of your system disk [YES]? The following products will be processed: decwmHU_HUU3 V1.2 Beginning installation of decwmHU_HUU3 V1.2 at 17:24 (continued on next page) B-32 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-9 (Cont.) Sample Installation of Hungarian language variant %VMSINSTAL-I-RESTORE, Restoring product save set A ... %VMSINSTAL-I-RELMOVED, Product's release notes have been moved to SYS$HELP. If one of DECwindows Motif OpenVMS UI V1.2-3 LNE1 (non-Latin1) language variants is already installed on your system, then you don't need to install LNE1 fonts. If you don't have any V1.2-3 LNE1 language variant installed, or you have any previous LNE1 language variant version installed on your system, then you MUST install LNE1 fonts. * Do you want to install LNE1 fonts [Y]? n %decwmHU_HUU3-I-INTRO, Installing DECwindows Motif for OpenVMS User Interface/Magyar V1.2 Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to and embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. A registered and loaded product authorization key for the DECwindows Motif for OpenVMS (VAX) V1.2-3/Magyar language variant kit is required. If you answer NO to the next question, the installation of the DECwindows Motif for OpenVMS (VAX) V1.2-3/Magyar language variant kit will be aborted. Product: DW-MOTIF-UI-MAGYAR Producer: DEC Version: 1.2-3 Release Date: * Does this product have an authorization key registered and loaded? y * Do you want to purge files replaced by this installation [YES]? n * Do you want to run the IVP after the installation [YES]? * Enter display destination for IVP [BIKETE]: (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-33 Example B-9 (Cont.) Sample Installation of Hungarian language variant %decwmHU_HUU3-I-NOMORE, No additional questions will be asked. %decwmHU_HUU3-I-TIME, Installation will take approximately 5 minutes. %VMSINSTAL-I-RESTORE, Restoring product save set B ... If your system startup procedure contains a line similar to the following: $ @SYS$MANAGER:DECW$STARTI18N P1 P2 then delete this line. DECW$STARTI18N procedure will be automatically invoked when starting or restarting DECwindows Motif. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP RESTART If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... Installation of decwmHU_HUU3 V1.2 completed at 17:26 VMSINSTAL procedure done at 17:26 B-34 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation B.10 Sample Installation of the Polish Language Variant Example B-10 Sample Installation of the Polish Language Variant $ @sys$update:vmsinstal decwmpl_plu3012 motif_path:[pl.kit.ssb] OpenVMS VAX Software Product Installation Procedure V6.1 It is 14-JUN-1995 at 17:31. Enter a question mark (?) at any time for help. %VMSINSTAL-W-NOTSYSTEM, You are not logged in to the SYSTEM account. %VMSINSTAL-W-ACTIVE, The following processes are still active: DECW$FD DECW$SERVER_0 DECW$MWM DEL DECW$TE_0FCB _FTA860: * Do you want to continue anyway [NO]? y * Are you satisfied with the backup of your system disk [YES]? The following products will be processed: decwmPL_PLU3 V1.2 Beginning installation of decwmPL_PLU3 V1.2 at 17:31 %VMSINSTAL-I-RESTORE, Restoring product save set A ... %VMSINSTAL-I-RELMOVED, Product's release notes have been moved to SYS$HELP. If one of DECwindows Motif OpenVMS UI V1.2-3 LNE1 (non-Latin1) language variants is already installed on your system, then you don't need to install LNE1 fonts. If you don't have any V1.2-3 LNE1 language variant installed, or you have any previous LNE1 language variant version installed on your system, then you MUST install LNE1 fonts. * Do you want to install LNE1 fonts [Y]? n %decwmPL_PLU3-I-INTRO, Installing DECwindows Motif for OpenVMS User Interface/Polski V1.2 Copyright Digital Equipment Corporation 1988, 1994. All rights reserved. (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-35 Example B-10 (Cont.) Sample Installation of the Polish Language Variant Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to and embodies the confidential technology of Digital Equipment Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. A registered and loaded product authorization key for the DECwindows Motif for OpenVMS (VAX) V1.2-3/Polski language variant kit is required. If you answer NO to the next question, the installation of the DECwindows Motif for OpenVMS (VAX) V1.2-3/Polski language variant kit will be aborted. Product: DW-MOTIF-UI-POLSKI Producer: DEC * Does this product have an authorization key registered and loaded? y * Do you want to purge files replaced by this installation [YES]? n * Do you want to run the IVP after the installation [YES]? * Enter display destination for IVP [BIKETE]: (continued on next page) B-36 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation Example B-10 (Cont.) Sample Installation of the Polish Language Variant %decwmPL_PLU3-I-NOMORE, No additional questions will be asked. %decwmPL_PLU3-I-TIME, Installation will take approximately 5 minutes. %VMSINSTAL-I-RESTORE, Restoring product save set B ... %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[CDA$LIBRARY.PL_PL] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$DEFAULTS.SYSTEM.PL_PL] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHLP.PL_PL] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSHLP.EXAMPLES.PL_PL] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSLIB.PL_PL] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[SYSMSG.PL_PL] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$LIBRARY.SYSTEM.PL_PL] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[DECW$DEFAULTS.USER.PL_PL] %VMSINSTAL-I-SYSDIR, This product creates system disk directory VMI$ROOT:[VUE$LIBRARY.USER.PL_PL] If your system startup procedure contains a line similar to the following: $ @SYS$MANAGER:DECW$STARTI18N P1 P2 then delete this line. DECW$STARTI18N procedure will be automatically invoked when starting or restarting DECwindows Motif. If your system is already running DECwindows Motif, restart DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP RESTART If your system is NOT already running DECwindows Motif, start DECwindows Motif with the following DCL command: $@SYS$MANAGER:DECW$STARTUP %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... Installation of decwmPL_PLU3 V1.2 completed at 17:34 VMSINSTAL procedure done at 17:34 (continued on next page) Motif V1.2-3 for OpenVMS Language Variants Sample Installation B-37 Example B-10 (Cont.) Sample Installation of the Polish Language Variant B-38 DECwindows Motif V1.2-3 for OpenVMS Language Variants Sample Installation _________________________________________________________________ Index A Bookreader files _______________________________ saving customized, 1-7 Account quotas Booting required for installation, DECwindows Motif for OpenVMS, 1-10 3-1 Adding DECwindows files, 4-14 standalone systems, 3-2 Alternate working device See AWD option C______________________________ Alternative console, 3-6 Console AUTOGEN utility alternative, 3-6 invoked by installation, 2-16 main, 3-6 invoking during installation, Customized Bookreader files 2-16 saving, 1-7 preparing for installation, 1-15 D______________________________ using to change system DECW$MOTIF_TAILOR utility parameters, 1-17 overview, 4-7 AWD option, 1-12 removing files from a system B disk, 4-10 _______________________________ DECW$TAILOR utility Backup adding base support files to confirming system backup, 2-4 a system disk, 4-16 of system disk, 1-19 overview, 4-14 Blocks using, 4-14 See Free blocks DECwindows Motif booting, 3-1 Index-1 DECwindows Motif (cont'd) Free global sections, 1-16 customizing system after installation, 4-1 G______________________________ installation, 2-1 Global pages installation requirements, See Free global pages 1-8 Global sections sample installation, A-1 See Free global sections starting, 3-1 DECwindows X11 Display server customizing startup, 4-1 H______________________________ Determining number of free Hardware blocks, 1-11 supported by DECwindows Motif Device name , 1-4 specifying for installation, 1-8 I______________________________ DFS-mounted disk Installation procedure, 2-2 determining free disk space, completing, 2-18 1-13 sample, A-1 for AWD, 1-13 starting, 2-2 on the system disk, 1-13 terminating instructions, 2-2 Disk space, 1-11 Installation requirements, 1-8 on the DFS-mounted AWD, 1-13 Installation Verification verifying, 2-10 Distributed File Service (DFS) Procedure See DFS-mounted disk See IVP Distribution media Installing DECwindows Motif mounting, 2-4 See Installation procedure IVP E______________________________ notification during product Error recovery, 2-19 installation, 2-15 running after starting F DECwindows Motif, 3-4 _______________________________ Free blocks determining, 1-11 Free global pages, 1-16 Index-2 K______________________________ N______________________________ Keyboard layout North American keyboard layout customizing, 4-3 , 4-2 Keyboard model number, 4-3 Notifying network users before Keymap names installation, 1-19 determining, 4-4 list, 4-4 O______________________________ Kit Operator window, 3-6 installing parts, 2-7 installing programming environment, 2-7 P______________________________ installing workstation device PAK registration, A-1 support, 2-7 See also License registration loading distribution media, Postinstallation problems 2-2 determining and reporting, preserving OSF/Motif Release 6-3 1.1.3, 2-7 Postinstallation tasks, 3-1 customizing DECwindows Motif, L______________________________ 4-1 Languages Privileges installing, 2-8 required for installation, License registration, 1-3 1-9 sample PAK registration, A-1 Product Authorization Key verifying, 2-12 See PAK registration Logging out Product name notifying users, 1-19 specifying for installation, 1-8 M______________________________ Programming environment Main console, 3-6 installing, 2-7, 2-8 Monitor Programming support 100 dpi, 4-2 choosing, 2-8 Monochrome workstations, 4-3 OSF/Motif Release 1.1.3 programming note, 1-6 Index-3 System disk (cont'd) Q______________________________ customizing with the Quotas, 1-9, 1-13 DECW$MOTIF_TAILOR utility, 4-10 R______________________________ customizing with the Rebooting the system, 2-12 DECW$TAILOR utility, 4-16 Release notes determining number of free accessing, 2-2, 2-5, 2-19 blocks, 1-11 displaying, 2-5, 2-6, 2-19 free space required for printing, 2-5, 2-6, 2-19 installation, 1-11, 2-10 Release Notes System Generation utility options, 2-5 See SYSGEN System parameters S______________________________ required, 1-14 Server startup reset by AUTOGEN, 2-16 customizing, 4-1 setting WINDOW_SYSTEM, 3-1 Shutting down the system System reboot, 2-12 notifying users, 1-19 System shutdown Software notifying users, 1-19 required operating system System tuning, 4-1 version, 1-4 T Starting DECwindows Motif, 3-1 _______________________________ on boot nodes, 3-3 Tuning the system, 4-1 on nonsatellites, 3-3 on satellites, 3-4 V______________________________ on standalone systems, 3-2 VMSINSTAL procedure, 2-2 on VMScluster systems, 3-3 requirements, 1-8 SYSGEN utility starting, 2-2 checking system parameter using AWD option, 2-3 values, 1-15 preparing for installation, W 1-15 _______________________________ SYSTEM account, 2-2 Window System disk operator, 3-6 adding DECwindows base WINDOW_SYSTEM system parameter support files, 4-14 setting, 3-1 backing up, 2-4 Index-4 Workstations customizing, 4-3 monochrome, 4-3 Index-5