Compaq_ACMSxp_for_OpenVMS_Alpha_____________________ Installation Guide Order Number: AA-QRFXE-TE June 1999 This document provides information about installing Compaq ACMSxp software on an OpenVMS Alpha system. Revision/Update Information: This is a revised manual. Software Version: Compaq ACMSxp Version 3.2A for OpenVMS Alpha Compaq Computer Corporation Houston, Texas ________________________________________________________________ June 1999 The information in this publication is subject to change without notice. COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. THIS INFORMATION IS PROVIDED "AS IS" AND COMPAQ COMPUTER CORPORATION DISCLAIMS ANY WARRANTIES, EXPRESS, IMPLIED, OR STATUTORY, AND EXPRESSLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, GOOD TITLE, AND AGAINST INFRINGEMENT. This publication contains information protected by copyright. No part of this publication may be photocopied or reproduced in any form without prior written consent from Compaq Computer Corporation. © 1999 Digital Equipment Corporation. All Rights Reserved. The software described in this guide is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance with the terms of the agreement. Compaq and the Compaq logo are registered in the United States Patent and Trademark Office. ACMS, ACMS Desktop, ACMSxp, ACMSxp Desktop, AlphaServer, AltaVista, DEC, DECnet, DECthreads, DIGITAL, OpenVMS, Tru64 UNIX, VAX, and VMS are trademarks of Compaq Computer Corporation. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Oracle is a registered trademark of Oracle Corporation. UNIX and X/Open are registered trademarks and The Open Group is a trademark of The Open Group in the United States and other countries. Other product names mentioned herein may be trademarks and /or registered trademarks of their respective companies. This document was prepared using VAX DOCUMENT Version 2.1. _________________________________________________________________ Contents Preface................................................... vii 1 Preparing to Install Compaq ACMSxp Software 1.1 Installing Product Authorization Keys (PAKs)........................................ 1-1 1.2 Required Layered Software..................... 1-2 1.3 Privileges Required for Installing ACMSxp Software...................................... 1-2 1.4 System Parameter Values Required for ACMSxp Software...................................... 1-3 1.5 Disk Space Requirements....................... 1-4 1.6 Required Order for Installing Software........ 1-5 1.7 Required Operating System Components.......... 1-6 1.7.1 Debugger Kit.............................. 1-6 1.8 Required Operating System Patches............. 1-7 1.9 Optional Layered Software..................... 1-8 1.10 DCE Procedures for the IVP.................... 1-8 2 Installing Compaq ACMSxp Software 2.1 Backing Up Your System Disk................... 2-1 2.2 Installing Compaq ACMSxp Software with VMSINSTAL..................................... 2-1 2.3 Running the ACMSxp Installation Verification Procedure (IVP)............................... 2-8 2.4 Error Recovery................................ 2-9 iii 3 After Installing Compaq ACMSxp Software 3.1 Installing the ACMSxp Management GUI Option... 3-1 3.1.1 Prerequisite Software..................... 3-1 3.1.2 System Requirements....................... 3-2 3.1.3 Procedures to Install the ACMSxp Management GUI............................ 3-2 3.1.4 Installing on a Japanese Windows NT System.................................... 3-3 3.2 Creating and Modifying User Accounts.......... 3-3 3.2.1 Setting Privileges for User Accounts...... 3-3 3.2.2 Setting Minimum Process Quotas for User Accounts.................................. 3-4 3.3 System Tuning................................. 3-7 3.3.1 Physical I/O Pages Parameter for ACMSxp Queuing................................... 3-7 3.3.2 Working Set Parameters for Request Queuing................................... 3-8 3.3.3 System Parameter for DECnet-Plus Software.................................. 3-8 3.3.4 Checking and Modifying System Parameters for ACMSxp Software....................... 3-8 3.3.5 Setting UCX Parameters for DCE Software... 3-11 3.3.6 Maintaining DECnet Configuration Values... 3-11 3.3.6.1 Guidelines for Calculating Links........ 3-12 3.3.7 Maintaining DECnet-Plus Configuration Values.................................... 3-13 3.4 Configuring DECdtm-Journal File and Logical Name.......................................... 3-15 3.4.1 Logical Name.............................. 3-15 3.4.2 Journal File.............................. 3-15 3.5 Modifying Node Startup Procedures............. 3-16 3.6 VMScluster Considerations..................... 3-16 3.6.1 Setting Up a Systemwide Default ACMSxp Version................................... 3-17 3.7 Setting Up ACMSxp with Japanese Language Support....................................... 3-18 iv 4 Deinstalling ACMSxp Software 4.1 Deinstallation Requirements................... 4-1 4.2 Actions Performed During Deinstallation....... 4-2 4.3 Rerunning an Incomplete Deinstallation........ 4-4 4.4 Questions Asked During Deinstallation......... 4-5 A Sample ACMSxp Installation B ACMSxp-Supplied Files B.1 Examples Directory............................ B-1 B.2 Executable Directory.......................... B-4 B.3 Help Directory................................ B-5 B.4 Library Directory............................. B-5 B.5 Manager Directory............................. B-6 B.6 Messages Directory............................ B-6 B.7 Test Directory................................ B-7 Index Examples 3-1 Examining NSP Attributes.................. 3-13 Tables 1-1 Required Layered Software................. 1-2 1-2 Privileges Required to Install ACMSxp Software and Run the IVP.................. 1-2 1-3 System Parameter Values for ACMSxp Software.................................. 1-3 1-4 ACMSxp Software Disk Space Requirements... 1-5 1-5 Required Operating System Components...... 1-6 1-6 Required Operating System Patches......... 1-7 1-7 Optional Layered Software................. 1-8 3-1 Prerequisite Software Version Numbers..... 3-2 3-2 Minimum Process Quotas for ACMSxp Commands.................................. 3-4 3-3 DECnet Phase IV Parameters................ 3-11 v _________________________________________________________________ Preface This manual presents information about installing Compaq ACMSxp software on the OpenVMS Alpha platform and deinstalling earlier versions of Compaq ACMSxp software. Intended Audience Read this manual if you are responsible for installing, maintaining, or deinstalling software for ACMSxp applications. To perform the installation and deinstallation procedures described in this manual, you must have access to a privileged OpenVMS system manager's account, and be familiar with the OpenVMS installation procedure, VMSINSTAL. Operating System Information Information about the versions of the OpenVMS operating system and other software compatible with this version of ACMSxp software is included in this manual. For information on the relationship of other software products with this version of ACMSxp software, refer to the Software Product Description (SPD). Use the SPD to verify which versions of your operating system are compatible with this version of ACMSxp software. vii Structure This manual has the following components, as shown in the following table: ___________________________________________________________ Component___Description____________________________________ Chapter 1 Describes preparations and requirements necessary for installing ACMSxp software, including dependent software. Chapter 2 Describes the installation of ACMSxp software. Chapter 3 Describes actions that may be necessary for the successful running of ACMSxp and dependent software after you install the ACMSxp software. Chapter 4 Describes the deinstallation of ACMSxp software. Appendix A Shows a sample installation. Appendix_B__Lists_the_files_from_the_ACMSxp_savesets.______ Conventions This document uses the following conventions: _________________________________________________________________ Convention____Description________________________________________ Ctrl/x Ctrl/x indicates that you hold down the Ctrl key while you press another key (indicated here by x). { } In format descriptions, braces indicate required elements. You must choose one of the elements. [ ] In format descriptions, brackets indicate optional elements. You can choose none, one, or all of the options. (Brackets are not optional, however, in the syntax of a directory name in an OpenVMS file specification.) ( ) In format descriptions, parentheses delimit the parameter or argument list. viii _________________________________________________________________ Convention____Description________________________________________ . . . In format descriptions, horizontal ellipsis points indicate an item that is repeated, an omission such as additional optional arguments, or additional parameters, values, or other information that you can enter. . Vertical ellipsis points indicate the omission of . information from an example or command format. The . information is omitted because it is not important to the topic being discussed. italic type Italic type in text emphasizes important information; indicates variables, product names, or sub-brands; and indicates complete titles of manuals. boldface Boldface type in examples indicates user input or type highlights important information. Boldface type in text highlights new terms defined in the text and the glossary. UPPERCASE Words in uppercase indicate a command, a parameter, a routine, the name of a file, the name of a file protection code, or an abbreviation for a system privilege. lowercase In format descriptions, words in lowercase indicate ______________parameters_or_arguments_that_you_specify.__________ ix 1 _________________________________________________________________ Preparing to Install Compaq ACMSxp Software This chapter describes: o Preparations and requirements necessary for installing Compaq ACMSxp software o Dependencies among Compaq ACMSxp software, the OpenVMS operating system, and layered products Compaq strongly recommends that you read the release notes for important installation information that might have been omitted from this manual, and then proceed with the installation. 1.1 Installing Product Authorization Keys (PAKs) Before you install and run ACMSxp on a newly licensed node or cluster, you must first register a License Product Authorization Key (License PAK) using the License Management Facility (LMF). To execute ACMSxp software, install the ACMS-DEV or ACMS-RT License PAK on each node or cluster on which ACMSxp software executes. PAKs are mailed online or in hardcopy (paper) format. To install each License PAK, do one of the following: o Execute the following command procedure: SYS$UPDATE:VMSLICENSE.COM Answer each prompt according to the information included in the hard copy of the License PAK. o At the DCL prompt, enter the LICENSE REGISTER command with the appropriate qualifiers that correspond to License PAK information. Preparing to Install Compaq ACMSxp Software 1-1 1.2 Required Layered Software Table 1-1 lists the dependent layered products that must be installed before installing ACMSxp software. Table_1-1_Required_Layered_Software________________________ Software_Product_Title__________Version____________________ Compaq DCE 1.4 Compaq TCP/IP Services for 4.1 ECO-4 OpenVMS RMS Journaling License Compaq_C________________________5.6-3______________________ In some cases, the layered product must be started before the ACMSxp installation or ACMSxp startup. 1.3 Privileges Required for Installing ACMSxp Software Table 1-2 lists the privileges required to install ACMSxp software and run the Installation Verification Procedure (IVP). Depending on the security setup of the filesystem directory in which ACMSxp software is installed, additional privileges may be required. Table 1-2 Privileges Required to Install ACMSxp Software __________and_Run_the_IVP__________________________________ Privilege___InstallationIVP________________________________ GRPNAM X GRPPRV X NETMBX X PRMGBL X SHARE X SYSNAM X X[1] [1]This_privilege_is_not_required_if_the_process_has_the___ rights identifier NET$DECLAREOBJECT. (continued on next page) 1-2 Preparing to Install Compaq ACMSxp Software Table 1-2 (Cont.) Privileges Required to Install ACMSxp __________________Software_and_Run_the_IVP_________________ Privilege___InstallationIVP________________________________ SYSPRV X X[2] TMPMBX X WORLD X [2]This_privilege_is_not_required_if_the_process_has_the___ rights identifier ACMS_START_TPSYSTEM. ___________________________________________________________ 1.4 System Parameter Values Required for ACMSxp Software The system parameter values shown in Table 1-3 are required to install ACMSxp software, run the IVP, and run ACMSxp software. Table_1-3_System_Parameter_Values_for_ACMSxp_Software______ System Parameter Name__________________Value________________________________ Contiguous free 0 + size in blocks of GBLPAGES SYS$SHARE:DCLTABLES.EXE Free GBLSECTIONS 100 CHANNELCNT 2 047 MIN_PQL_DASTLM 4 096 MIN_PQL_DBIOLM 1 000 MIN_PQL_DBYTLM 50 000 MIN_PQL_DCPULM 0 MIN_PQL_DDIOLM 100 MIN_PQL_DENQLM 10 000 MIN_PQL_DFILLM 200 MIN_PQL_DJTQUOTA 1 024 MIN_PQL_DPGFLQUOTA 100 000 MIN_PQL_DPRCLM 12 (continued on next page) Preparing to Install Compaq ACMSxp Software 1-3 Table 1-3 (Cont.) System Parameter Values for ACMSxp __________________Software_________________________________ System Parameter Name__________________Value________________________________ MIN_PQL_DTQELM 100 MIN_PQL_MASTLM 4 096 MIN_PQL_MBIOLM 1 000 MIN_PQL_MBYTLM 50 000 MIN_PQL_MCPULM 0 MIN_PQL_MDIOLM 100 MIN_PQL_MENQLM 10 000 MIN_PQL_MFILLM 200 MIN_PQL_MJTQUOTA 0 MIN_PQL_MPGFLQUOTA 100 000 MIN_PQL_MPRCLM 12 MIN_PQL_MTQELM____________100______________________________ These are minimum values required for running the IVP. You may have to further tune the parameters. For running user applications, at a minimum, all values must be nonzero. Refer to Section 3.3.4 for guidelines on checking and modifying system parameters. See Sections 3.2.1 and 3.2.2 and for the privileges and quotas required to run ACMSxp software. 1.5 Disk Space Requirements Table 1-4 lists the minimum disk space requirements. 1-4 Preparing to Install Compaq ACMSxp Software Table_1-4_ACMSxp_Software_Disk_Space_Requirements________________ Peak Usage_________________(BlocksNet_________________________________ ACMSxp Saveset 30 20 000 + size of On system disk 000 SYS$LIBRARY:DCLTABLES.EXE On another disk System disk 24 425 + size of 252 SYS$LIBRARY:DCLTABLES.EXE Target disk 25 26 601 000 For IVP at +20 +100 installation__________000________________________________________ To determine the number of free disk blocks on the current system disk, enter the following command at the DCL prompt: $ SHOW DEVICE SYS$SYSDEVICE . . . $ This command displays the number of free blocks on the system disk to which the systemwide logical name SYS$SYSDEVICE points. To determine the number of free disk blocks on another disk, enter at the DCL prompt a command in the following format: SHOW DEVICE disk This command displays the number of free blocks on the disk specified. 1.6 Required Order for Installing Software To ensure problem-free installation of software on your system, install OpenVMS and layered software in the following order: 1. Compaq C (required) 2. Compaq TCP/IP Services (UCX) (required) 3. DECnet or DECnet-Plus (required) Preparing to Install Compaq ACMSxp Software 1-5 4. RDB (optional)-install before DECnet-Plus 5. Compaq DCE (required) The order of installation for the remaining software products is not important for ACMSxp operation. 1.7 Required Operating System Components Table 1-5 lists the operating system components required by ACMSxp. Table_1-5_Required_Operating_System_Components_____________ Component:____________Including:___________________________ OpenVMS Alpha DECdtm Version 7.1 or OpenVMS Debugger V7.2X-010 OpenVMS Alpha Version_6.2________________________________________________ 1.7.1 Debugger Kit To have STDL source level debugging function properly, ACMSxp software requires the proper version of the OpenVMS Debugger. If you are installing ACMSxp software for development purposes, check whether the following image is present on the system on which you are performing the installation. SYS$SHARE:DEBUGSRVSHR_V72X.EXE If the image is present, check the version of the image. For example: $ ANAL/IMAGE/HEADER/INTER SYS$SHARE:DEBUGSRVSHR_V72X.EXE . . . Image Identification Information image name: "DEBUGSRVSHR" image file identification: "V7.2X-010" Press Return until you see the heading Image Identification Information and the line image file identification. If the version is V7.2X-010 or later, you have the proper Debugger version. 1-6 Preparing to Install Compaq ACMSxp Software If the image is not present or its version is not at the appropriate revision level, you must install the Debugger kit provided with the ACMSxp kit. Find the installable kit ADX072.* in the same directory in which you locate the ACMSxp kit and use VMSINSTAL to make it available on the ACMSxp system. Installing the debugger kit does not supersede the current version of the debugger on your system. Both the old and new versions are available; unless you change the default, the old version remains the default. The ACMS DEBUG SERVER command uses the newer version of the debugger. You do not need to run any other debugger command procedures provided with the OpenVMS Debugger kit to make the newer version available to ACMSxp software. To make the newer version the default systemwide debugger, follow the instructions displayed by the OpenVMS Debugger kit installation procedure. 1.8 Required Operating System Patches Table 1-6 lists the operating system patches required by ACMSxp software. Table_1-6_Required_Operating_System_Patches________________ VersionPatch_________________Comment:______________________ 6.2 ALPBOOT12_062 Or later patch revision level. ALPCMAR04_062 ALPRMS02_062 ALPSYS14_062 ALPY2K02_062 7.1 ALPACRT04_071 ALPPTHR01_071 ALPRMS02_071 _______ALPSYSA01_071_______________________________________ Preparing to Install Compaq ACMSxp Software 1-7 1.9 Optional Layered Software Table 1-7 lists the optional dependent software products that can be used with ACMSxp. Table_1-7_Optional_Layered_Software________________________ Software Product Name_____________Version_____Notes_________________________ COBOL 2.5 DECset Facilitates application development. Oracle_Rdb_______6.1_______________________________________ These products can be installed and used independently of ACMSxp installation and operation. 1.10 DCE Procedures for the IVP The following DCE setup is required to run the IVP: o Server principal acmsxp_svr o Server key file in the following directory: DCE$SPECIFIC:[KRB5] o User principal(s) in the DCE group users Follow these steps: 1. Log in to DCE as cell_admin. $ dce_login cell_admin Enter Password: $ The command logs you in to DCE and gives you the proper credentials to execute the security operations. ________________________ Note ________________________ All DCE commands are case sensitive. ______________________________________________________ 1-8 Preparing to Install Compaq ACMSxp Software 2. Create a group called users under which the IVP runs. $ rgy_edit Current site is: registry server at /.../avertz_cell rgy_edit=> domain group Domain changed to: group rgy_edit=> add users -f "IVP access" rgy_edit=> exit $ The add subcommand creates the DCE group users. The exit command leaves the program and returns control to the DCL prompt 3. Provide namespace directory creation access for group users. In the commands shown, replace the cell name avertz_cell with the name of your cell. $ acl_edit /.../avertz_cell -m group:users:rwdtcia $ acl_edit /.../avertz_cell -ic -m group:users:rwdtcia $ acl_edit /.../avertz_cell -io -m group:users:rwdtc $ cdscp show cell /.: SHOW CELL /.../avertz_cell AT 1998-2-9-16:27:01 Namespace Uuid = e484c407-d0b8-11cd-835b-08002b187bb3 Clearinghouse Uuid = e2a64d26-d0b8-11cd-835b-08002b187bb3 Clearinghouse Name = /.../avertz_cell/avertz_ch Replica Type = Master Tower = ncacn_ip_tcp:16.119.0.166[] Tower = ncadg_ip_udp:16.119.0.166[] $ acl_edit /.../avertz_cell/avertz_ch -m group:users:rwdtc $ The first command modifies the parent directory ACL in the cell namespace with a group entry of users, allowing all permissions to any principal that is a member of the group. The second and third commands modify the initial container creation ACL and initial object creation ACL similarly to the first command so that any subdirectories and objects subsequently created have the appropriate permissions. Preparing to Install Compaq ACMSxp Software 1-9 The fourth command displays the name of the clearinghouse to be used in the fifth command. The fifth command modifies the clearinghouse directory in the cell with a group entry of users, allowing the permission w to any principal that is a member of that group. Any principal belonging to the group can specify a namespace directory during TPsystem creation. For example, this access allows a member principal to create the ACMSxp default namespace directory in the cell avertz_cell. 4. Create the DCE server principal and account for the IVP. $ rgy_edit rgy_edit=> domain principal Domain changed to: principal rgy_edit=> add acmsxp_svr -f "IVP TPsystem default server principal" rgy_edit=> domain account Domain changed to: account rgy_edit=> add acmsxp_svr -g users -o none -mp Celladmin_Passwd -pw SvrPasword rgy_edit=> The add subcommand creates the acmsxp_svr server principal in the namespace and adds an account for the server principal. The string Celladmin_Passwd on the -mp option is the cell_admin account password. The string SvrPasword on the -pw option is the acmsxp_svr account password. Use this same password when you create the server key in the local directory. 5. Create the server key in the local directory. a. Use rgy_edit subcommands to create the file and specify the key. For example: rgy_edit=> ktadd -p acmsxp_svr -f dce$local:[krb5]acmsxp_svr -pw SvrPasword rgy_edit=> ktlist -p acmsxp_svr -f dce$local:[krb5]acmsxp_svr /.../avertz_cell/acmsxp_svr 1 rgy_edit=> The ktadd subcommand with the -p option gives the name of the server principal acmsxp_svr and with the -f option specifies the key file for the TPsystem server principal. Specify the same name for the key file and the name of the server principal. 1-10 Preparing to Install Compaq ACMSxp Software The string SvrPasword on the -pw option is the acmsxp_svr account password. The utility verifies the password and creates the server key for the principal in the named key file. Supply the same password here that you supplied when you created the DCE account for the server principal. This ensures that the key in the DCE registry is the same as the key in the local file. b. Ensure that the operating system user account under which the IVP is to run has read access to the acmsxp_svr key file. 6. Terminate DCE access. rgy_edit=> exit bye. $ kdestroy $ The commands erase the cell_admin security credentials from the network. Refer to Compaq DCE for OpenVMS Alpha Release Notes for information on UCX TCP settings and to the Compaq DCE for OpenVMS Alpha Installation and Configuration Guide for cell configuration information. Preparing to Install Compaq ACMSxp Software 1-11 2 _________________________________________________________________ Installing Compaq ACMSxp Software This chapter describes the installation of the Compaq ACMSxp software from the Compaq ACMSxp for OpenVMS Alpha kit. 2.1 Backing Up Your System Disk At the beginning of the installation, VMSINSTAL asks whether you have backed up your system disk. Compaq recommends that you do a system disk backup before installing any software. Use the backup procedures that have been established at your site to do this backup. For details about performing a system disk backup, see the section on the BACKUP Utility in the OpenVMS documentation set. 2.2 Installing Compaq ACMSxp Software with VMSINSTAL To start the installation: 1. Log in to the SYSTEM account. 2. Set default to the SYS$UPDATE directory. For example: USERNAME: SYSTEM PASSWORD: $ SET DEFAULT SYS$UPDATE $ 3. If you want to run the Installation Verification Procedure (IVP) during the installation, do the following: a. Ensure that the DECdtm software is configured on the system. See Section 3.4. Installing Compaq ACMSxp Software 2-1 b. Log in to DCE using the DCE principal created as described in Section 1.10. For example: $ DCE_LOGIN acmsxp_svr Enter Password: $ DCE software prompts for the password for the account. 4. Invoke VMSINSTAL. Use the following syntax: @VMSINSTAL product-name device-name [ OPTIONS option-1 [, . . . ] ] The VMSINSTAL parameters are: product-name The installation name for the component. For ACMSxp software, use the following name. ACMSXPAVME01032 device-name The name of the device on which you plan to mount the medium. For example, MTA0: is the device name for a tape drive. It is not necessary to use the console drive for this installation. However, if you do use the console drive, complete the installation, remove the installation medium, and replace any medium you removed. OPTIONS An optional parameter indicating that one or more VMSINSTAL options are being supplied. This parameter is followed by a space, and the requested options. Separate multiple options with commas (,); do not include spaces in the options list. You can use the following VMSINSTAL options for the ACMSxp installation: A The auto_answer option initially creates a file that contains your answers to VMSINSTAL questions and prompts. You can then use the option (and the answer file) to save time during a reinstallation (typically after upgrading your system). 2-2 Installing Compaq ACMSxp Software AWD The alternate working device option allows you to specify an alternate disk device on which to create the temporary working directory used by VMSINSTAL during a product installation. Specify the AWD option using the following format: AWD=device This option allows you to perform an installation with fewer free blocks on the system disk than are otherwise required. G The get saveset option lets you store product savesets temporarily on a magnetic tape or in a disk directory. L The file log option logs all activity to the terminal during installation. N The notes option prints the release notes. R The alternate root option lets you install the product to a system root other than that of the running system. See the OpenVMS documentation on software installation in the OpenVMS System Management Subkit for detailed information on these options. The following command invokes VMSINSTAL and installs ACMSxp software from the MTA0: tape drive: $ @SYS$UPDATE:VMSINSTAL ACMSXPAVME01032 MTA0: OPTIONS N OpenVMS Alpha Software Product Installation Procedure V7.2 It is 09-JUN-1999 at 10:21. Enter a question mark (?) at any time for help. If you do not supply either the product name or the device name, VMSINSTAL prompts you for this information later in the installation procedure. If you are not logged into the system under the SYSTEM account, VMSINSTAL displays a warning message. The installation procedure continues in the following stages: 1. Displaying existing processes Installing Compaq ACMSxp Software 2-3 %VMSINSTAL-W-ACTIVE, The following processes are still active: OSITPCM_SERVER EPC$REGISTRAR DCE$RPCD DCE$LDSD * Do you want to continue anyway [NO]? Y These are the processes for the software that is required prior to ACMSxp installation. 2. System backup VMSINSTAL asks the following question to ensure that your system disk is properly backed up: * Are you satisfied with the backup of your system disk [YES]? Always back up your system disk before performing an installation. If you are satisfied with the backup of your system disk, press Return. Otherwise, answer No to stop the installation. After you back up your system disk, you can restart the installation. 3. Mounting the media VMSINSTAL instructs you to mount the ACMSxp distribution medium on the device you specified when you invoked VMSINSTAL. Please mount the first volume of the set on MTA0:. *Are you ready? Y Mount the medium and answer Yes to the question Are you ready? If you entered the wrong device name when you invoked VMSINSTAL and need to restart the installation, answer NO in response to the question. To abort the installation for any other reason, press Ctrl/Y. If you abort the installation, you must delete any subdirectories in the root installation directory and restart the installation procedure. VMSINSTAL then reads the media and begins the installation of ACMSxp software. The following message appears: 2-4 Installing Compaq ACMSxp Software %MOUNT-I-MOUNTED, ACMSXPAVME01032 MOUNTED ON _$200$MTA0: The following products will be processed: ACMSXPAVME01 V3.2 Beginning installation of ACMSXPAVME01 V3.2 at 10:24 %VMSINSTAL-I-RESTORE, Restoring product saveset A... . . . 4. Product Authorization Key VMSINSTAL asks whether you have the product authorization key: * Does this product have an authorization key registered and loaded? Answer Yes or No. You can install the product without having registered and loaded the key, but you cannot run the IVP. 5. Specifying a kit location VMSINSTAL asks where to install the ACMSxp software: * Where would you like to install ACMSxp [SYS$COMMON:[ACMSxpV0321]]: Enter the device and directory. For example: DISK1:[ACMS.ACMS_INSTALL_DIR] The directory must either not yet exist, or exist and be empty. If the directory is not empty, the installation procedure prompts you to supply another directory, or you may exit. 6. Running the IVP If you are logged in to DCE, VMSINSTAL asks whether you want to run the Installation Verification Procedure (IVP): * Do you want to run the IVP after the installation [YES] ? You can run the IVP during the installation, or you can run it separately after installation. For more information about the IVP, see Section 2.3. Installing Compaq ACMSxp Software 2-5 If the disk you chose has enough free space to complete the installation but not to run the IVP, you can either stop the installation or complete it without running the IVP. See Table 1-4 for disk space requirements. If you are not logged in to DCE, you see the following message: %ACMSXP-W-IVPDCELGN, You must be logged in to DCE (use dce_login) to run IVP. 7. Specifying the System Default Installation VMSINSTAL asks whether you want this to be the system default installation of ACMSxp: * Do you want this to be the system default installation of ACMSxp? [YES] If you answer No, each user must execute this version's ACMS_SET_VERSION.COM in order to use ACMSxp software. If you answer Yes, this version becomes the system default version. That is, when the system runs the ACMSxp startup procedure, users do not have to run ACMS_SET_VERSION.COM, because this version of ACMSxp is defined systemwide. For information on changing a local version to a system default version, see Section 3.6.1. 8. Displaying information on the ACMS_START_TPSYSTEM rights identifier VMSINSTAL displays this next section if it detects that the rights identifier ACMS_START_TPSYSTEM is not present. If the rights identifier is present, then after you answer the question about the default installation, no more questions are asked. In order to run ACMSxp without the sysprv privilege the rights identifier ACMS_START_TPSYSTEM will be added to your system. If ACMSxp is being installed in a cluster and the rightslist.dat file is not shared amongst cluster members then the rights identifier must be created on all other cluster members that will run ACMSxp. You can run the image ACMS_SYS_DIR:ACMS_ADD_IDENTIFIER.EXE to create or recreate the ACMS_START_TPSYSTEM rights identifier. 2-6 Installing Compaq ACMSxp Software The identifier ACMS_START_TPSYSTEM is used in creating an ACE on the LNM$SYSTEM_DIRECTORY logical name table. This ACE will allow ACMSxp to create logical name tables as needed and attach them to the LNM$SYSTEM_DIRECTORY logical name table. The following example shows how to add this ACE to the LNM$SYSTEM_DIRECTORY logical name table using the ACMS_START_TPSYSTEM identifier. $ SET SECURITY LNM$SYSTEM_DIRECTORY/CLASS=LOGICAL_NAME_TABLE - /ACL=(IDENTIFIER=ACMS_START_TPSYSTEM,ACCESS=WRITE+READ+CREATE) You should place this command in a system startup file such as sylogicals.com or sysecurity.com so that the ACL will be preserved across system reboots. The rights identifier ACMS_START_TPSYSTEM will now be added to your system. %ACMSXP01-I-ADDID, This installation adds an IDENTIFIER named ACMS_START_TPSYSTEM. The rights identifier ACMS_START_TPSYSTEM will now be granted to the logical name table LNM$SYSTEM_DIRECTORY. This identifier should be granted to those accounts that will start ACMSxp tpsystems using the following command: UAF> GRANT/IDENTIFIER ACMS_START_TPSYSTEM %UAF-I-GRANTMSG, identifier ACMS_START_TPSYSTEM granted to CRAMER The command in this example grants the identifier ACMS_START_TPSYSTEM to the user named Cramer. Cramer becomes the holder of the identifier and any resources associated with it. 9. Continuing the installation If the rights identifier ACMS_START_TPSYSTEM was not present, then you are asked to enter return to allow the installation to continue. * Press return to Continue: After you enter Return, VMSINSTAL ends the questions. VMSINSTAL signals the end of the questions as follows: %ACMSXP-I-DONEASK, No more questions will be asked . . . Installing Compaq ACMSxp Software 2-7 The procedure copies files and prints some instructions for you to follow. The elapsed time should be no more than ten minutes. When a message similar to the following appears, the installation is done: VMSINTSTAL procedure done at 12:07 See Section 2.4 for discussion of errors that might occur. 2.3 Running the ACMSxp Installation Verification Procedure (IVP) The ACMSxp IVP verifies that the ACMSxp product installation is sound by: o Checking that all ACMSxp installation prerequisites are met. o Compiling and linking STDL servers to ensure that STDL task servers can be compiled and linked (if an ACMSxp developer license is active). o Executing ACMSxp run-time system operations, to ensure that STDL servers can be run. o Performing ACMSxp system management operations using the ACMSxp director software, to ensure that management software can be run. o Checking that ACMSxp request queuing services are functional. Run the ACMSxp IVP automatically from VMSINSTAL during ACMSxp product installation or at any time after an installation of the ACMSxp product. To run the ACMSxp IVP outside of the installation, perform the following steps: 1. Ensure that the DECdtm software is configured on the system. See Section 3.4. 2. Log in to DCE using the DCE principal that you created for the IVP as described in Section 1.10. For example: $ DCE_LOGIN acmsxp_svr Enter Password: $ DCE software prompts for the password for the account. 2-8 Installing Compaq ACMSxp Software 3. Execute the following commands at the DCL prompt: $ @USER1:[ACMSXPV0321.SYSEXE]ACMS_SET_VERSION ACMSxp V3.2-1 for OpenVMS Alpha Copyright (c) 1993, 1999 by Digital Equipment Corporation. All Rights Reserved. Using ACMSxp in USER1:[ACMSXPV0321.SYSEXE] $ @ACMS_SYS_DIR:ACMS_RUN_IVP.COM . . . $ These commands set the ACMSxp version and start the IVP, which displays status messages about operations being performed. More detailed information is stored in log files. To examine the contents of ACMSxp IVP log files, follow these steps: 1. To read about the operations performed during an IVP run, enter at the DCL prompt a command in the following format: TYPE device-name:[ install_root ]ACMS_IVP_RUN.TXT The variable install_root is the directory specification of the location holding the ACMSxp software kit. 2. To examine the IVP log file, enter at the DCL prompt a command in the following format: ACMS LIST LOG [install_root.SYSTEST]IVP_TPSYS_name_ DEFAULT.LOG The binary file IVP_TPSYS_name_DEFAULT.LOG is created by the ACMSxp event logger during the IVP. This file is generated using the local language in effect when the IVP is executed. 2.4 Error Recovery If errors occur during the installation itself or when the IVP is running, VMSINSTAL displays failure messages. If the installation fails, you see the following message: %VMSINSTAL-E-INSFAIL, The installation of ACMSxp V3.2 has failed. Installing Compaq ACMSxp Software 2-9 If the IVP fails, you see these messages: The ACMSxp IVP aborted on error Use the following commands to obtain more information: $ TYPE/PAGE ACMS_IVP_RUN.TXT $ ACMS LIST LOG [.SYSTEST>]IVP_TPSYS__DEFAULT.LOG %VMSINSTAL-E-INSFAIL, The installation of ACMSxp V3.2 has failed. If any of the following conditions exist, errors can occur during the installation: o The operating system is incorrect. o A version of prerequisite software product is incorrect. o Quotas necessary for successful installation were insufficient. o System parameters necessary for successful installation were insufficient. o The OpenVMS help library is currently in use. For descriptions of the error messages generated by these conditions, see the OpenVMS documentation on system messages, recovery procedures, and OpenVMS software installation. Use the online message facility with a search string from the error message. For example: $ HELP/MESSAGES LOWQUOTA LOWQUOTA, the following account quotas may be too low: Facility: VMSINSTAL, Install Procedures Explanation: When VMSINSTAL begins an installation, it makes sure that your process quotas are valid. This check failed. User Action: You are asked if you want to continue the installation. Compaq recommends that this situation is corrected before continuing. . . . $ 2-10 Installing Compaq ACMSxp Software The command tells the software to display all messages containing the specified string. The software displays the name of the facility responsible for the message, an explanation of what the message means, and recommended user actions to follow the recover from the error condition. If you are notified that any of these conditions exist, take the appropriate action as described in the message. For information on installation requirements, see Sections 1.3 and 1.4. If the installation fails, you must delete any subdirectories in the root installation directory and restart the installation procedure. Installing Compaq ACMSxp Software 2-11 3 _________________________________________________________________ After Installing Compaq ACMSxp Software This chapter describes actions to take after installing ACMSxp software but before running the installed ACMSxp software. 3.1 Installing the ACMSxp Management GUI Option With the Compaq ACMSxp for OpenVMS Alpha software, you have an option for the ACMSxp Administration Graphic User Interface (GUI) that you can install on a Windows NT Intel platform and use to manage your ACMSxp applications. This software provides ACMSxp system management capabilities for a PC Windows environment. Referred to as the ACMSxp Management GUI, the software provides easy access to similar functionality available through the ACMSxp Command Line Interface (CLI) director. The GUI comes with an extensive Windows Help file. 3.1.1 Prerequisite Software Before you install the GUI option, ensure that you do the following on the Windows NT Intel system: o Configure the Windows NT system to use the TCP/IP protocol. This can be a local configuration. o Establish a local disk, either NTFS or FAT, with long file names. o Install either the Compaq DCE for Windows NT Runtime Services kit or the Compaq DCE for Windows NT Application Developer's kit. o Establish access to a DCE CDS server and a DCE security server either locally or on your network. After Installing Compaq ACMSxp Software 3-1 The versions of the prerequisite software are shown in Table 3-1. Table_3-1_Prerequisite_Software_Version_Numbers____________ Software______________Version_Number_______________________ Compaq DCE 2.0 Windows_NT____________4.0_with_Service_Pack_3______________ 3.1.2 System Requirements Install the GUI software on Windows NT Intel platforms only. The software requires: o A minimum screen resolution of 800x600 pixels. o 20 megabytes of free disk space during the installation. o 10 megabytes of disk space after installation. 3.1.3 Procedures to Install the ACMSxp Management GUI To install the ACMSxp Management GUI option on the Windows NT Intel system, perform the following steps. 1. On the Windows NT system, create a new disk directory to contain the GUI option set-up software. 2. On the Windows NT system, change directory to the newly created directory. 3. From the system on which you installed the ACMSxp software, copy the self-expanding file containing the GUI option set-up software to the newly created directory. Named gui_kit_intel.exe, this file resides in the directory to which the ACMS_SYS_DIR logical name points. 4. From the newly created directory on the Windows NT system, run the gui_kit_intel.exe file to extract the set-up files. 5. From the newly created directory on the Windows NT system, run the setup.exe program to install the ACMSxp Management GUI. 3-2 After Installing Compaq ACMSxp Software The setup.exe program asks you to choose either the companion or the standalone software option. The standalone software option is designed to run on a Windows NT system that does not have ACMSxp software installed. If you do not have ACMSxp base software installed on the Windows NT system, install the GUI standalone software option. Because the standalone software option registers environment variables that are used by other ACMSxp components, do not install this option if you have any version of ACMSxp software installed on the Windows NT system. The companion software option is designed to run on a Windows NT system with Compaq ACMSxp for Windows NT software also running. The gui_kit_readme_intel.txt file in the directory to which the ACMS_SYS_DIR logical name points contains more information about the options. 3.1.4 Installing on a Japanese Windows NT System During the installation of the ACMSxp management GUI on a Japanese Windows NT platform, a dialog box may appear with the following error message: There is not enough disk space in one or more drives. If this message appears, click Install Now and the installation proceeds normally. 3.2 Creating and Modifying User Accounts To run ACMSxp software, users require: o User account privileges to create, delete, and start a TPsystem; issue management directives; and use ACMSxp commands o Minimum process quotas to use ACMSxp commands Sections 3.2.1 and 3.2.2 describe these requirements. 3.2.1 Setting Privileges for User Accounts To perform the following operations, a user account needs to follow prescribed requirements. o Create or delete a TPsystem o Start a TPsystem After Installing Compaq ACMSxp Software 3-3 o Run task servers and processing servers under a UIC different from that of the TP controller o Execute any management directive and ACMS command o Debug a server using the ACMS command DEBUG SERVER See Compaq ACMSxp Developing and Managing Applications for information on user account and UIC requirements. If you need to modify privileges, use the OpenVMS Authorize Utility (described in Section 3.2.2). To add a privilege, enter the MODIFY command at the UAF> prompt, using the following format: MODIFY account-name/PRIVILEGE=([NO]privilege-name [, . . . ]) The command accesses the system account file and the account record specified. Messages displayed tell you whether the modification is made. 3.2.2 Setting Minimum Process Quotas for User Accounts Table 3-2 lists the process quotas required for ACMSxp commands. Table_3-2_Minimum_Process_Quotas_for_ACMSxp_Commands_______ Minimum Quota____________Setting___________________________________ ASTLM 24 BIOLM 18 BYTLM[1] 100 000 CPU (none) DIOLM 22 ENQLM 3 200 FILLM 200 JTQUOTA 4 096 MAXACCTJOBS 0 [1]BYTLM_must_be_at_least_150_000_to_run_the_IVP.__________ (continued on next page) 3-4 After Installing Compaq ACMSxp Software Table 3-2 (Cont.) Minimum Process Quotas for ACMSxp __________________Commands_________________________________ Minimum Quota____________Setting___________________________________ MAXDETACH 0 MAXJOBS 0 PBYTLM 0 PGFLQUO 75 000 PRCLM 10 PRIO 4 QUEPRIO 0 SHRFILLM 0 TQELM 100 WSDEF 1 024 WSEXTENT 8 192 WSQUO______________4_096___________________________________ If you compile large task groups (for example, 600 tasks) or large processing groups (for example, 300 procedures) with a page file quota set to the minimum required, you can see the following error from the DEC C compiler: %CC-F-TEXT, Compiler abort - virtual memory limits exceeded. To eliminate the error, increase the paging file quota (Pgflquo) to 300 000. The minimum BYTLM quota for the user process that starts a TPsystem is shown in Table 3-2. If your application uses large audit records, you may need to set the BYTLM quota to an even larger value. Use the VMS Authorize Utility (AUTHORIZE) to verify and change user account quotas. Follow these steps: 1. Set your default directory to SYS$SYSTEM and run AUTHORIZE: $ SET DEFAULT SYS$SYSTEM $ RUN AUTHORIZE UAF> After Installing Compaq ACMSxp Software 3-5 2. At the AUTHORIZE prompt (UAF>), enter the SHOW command with an account name to check a particular account. For example: UAF> SHOW SYSTEM . . . UAF> The command displays the current settings for the SYSTEM account. 3. To change a quota, enter the MODIFY command at the UAF> prompt, using the following format: MODIFY account-name/quota-name=nnnn The following example changes the Bytlm quota for the SYSTEM account to 100 000: UAF> MODIFY SYSTEM/BYTLM=100000 UAF> The command access the SYSTEM account record to make the change. 4. Exit from the Authorize Utility with the EXIT command: UAF> EXIT . . . $ When you exit from the Authorize Utility, the system displays messages that indicate whether changes were made. You must log out and log in again for the changes to take effect. For more information on modifying account quotas, see the description of the Authorize Utility in the OpenVMS System Management Subkit. See Compaq ACMSxp Developing and Managing Applications for information on using the ACMS_PROCESS_QUOTAS logical name to set process quotas for ACMSxp application servers. 3-6 After Installing Compaq ACMSxp Software 3.3 System Tuning ACMSxp software requires certain system software resources to run properly. The system parameter values shown in Table 1-3 are required to run ACMSxp software. 3.3.1 Physical I/O Pages Parameter for ACMSxp Queuing If your ACMSxp application uses queuing, determine the requirements for the system parameter PIOPAGES (used for RMS journaling). To determine the minimum value that a queuing feature might require, use the following variables: num_piopages Minimum number of physical I/O pages needed for the ACMSxp queuing server m_threads Maximum number of threads in one of the ACMSxp system servers supplying the queuing service Use the formula in (3-1) for each server supplying a queuing service used in a TPsystem. num_piopages = (18*m_threads)*1.05 (3-1) The number of threads m_threads equals value of the maximum threads attribute for ACMS_RECQU_SVR (record queue server) or ACMS_RSEND_SVR (recoverable send server which uses the send queue). The value can be found through ACMSxp system administration software under the maximum threads attribute. For ACMS_QUEUE_SVR (request queue server), multiply the maximum thread attribute value by 2. For example, if the value for the request queue server displayed through ACMSADMIN is 15, use 30 for m_threads in the formula shown in (3-1). Refer to Section 3.3.4 for guidelines on checking and modifying system parameters. After Installing Compaq ACMSxp Software 3-7 3.3.2 Working Set Parameters for Request Queuing Compaq recommends that the ACMSxp system server acms_queue_ svr process run with the following working set parameter values. WSEXTENT 100 000 WSQUO 100 000 If all processes on the system can run with these values, refer to Section 3.3.4 for guidelines on checking and modifying system parameters. If all processes on the system do not have to run with these values, use the ACMSxp director to add in the environment variables attribute of the queue server entity an entry for the name ACMS_PROCESS_ QUOTAS and values for the parameter values. Refer to Compaq ACMSxp Developing and Managing Applications for guidelines on configuring servers and setting values for this name. 3.3.3 System Parameter for DECnet-Plus Software If a TPsystem uses DECnet-Plus software, set the system parameter KSTACKPAGES as follows: KSTACKPAGES = 2 Refer to Section 3.3.4 for guidelines on checking and modifying system parameters. 3.3.4 Checking and Modifying System Parameters for ACMSxp Software If you need to check current values of system parameters for ACMSxp and related product requirements listed in Sections 1.4, 3.3.1, and 3.3.3, follow the procedures outlined in this section. To check the values of system parameters, enter the following command at the DCL prompt to invoke SYSGEN: $ RUN SYS$SYSTEM:SYSGEN SYSGEN> The command starts the SYSGEN program, which displays its prompt, at which you can enter commands. At the SYSGEN> prompt, enter the SHOW command and the name of the parameter. For example: 3-8 After Installing Compaq ACMSxp Software SYSGEN> SHOW CHANNELCNT . . . SYSGEN> The command accesses the current value of the CHANNELCNT parameter in memory and displays its value. After you examine the parameter with the SHOW command, enter the EXIT command at the SYSGEN> prompt. Use the AUTOGEN command procedure to change system parameters. AUTOGEN automatically adjusts values for parameters that are associated with the values you reset manually. To change system parameters with AUTOGEN, edit the following file: SYS$SYSTEM:MODPARAMS.DAT Use an editor to access the file. To change a parameter value listed in this file, delete the current value associated with that parameter and enter the new value. To add a new parameter, add a line to the file that includes both the name of the parameter and its value. For example: CHANNELCNT = 2047 You can help tune your system. Specify a minimum value for parameters in the parameters file to let AUTOGEN decide the most efficient value at or above the specified amount. To indicate parameters with minimum values, precede the parameter name with MIN_ and supply the minimum value. For example: MIN_CHANNELCNT = 2047 The values for GBLPAGES and GBLSECTIONS represent the number of contiguous free global pages and global sections required for the installation, not the total number you need to run your system and other software. To install and run ACMSxp software, you must have sufficient contiguous free global pages and free global sections. You must first find out how many free global pages and sections you have on your system. If you need to After Installing Compaq ACMSxp Software 3-9 increase the GBLPAGES and GBLSECTIONS system parameters, use AUTOGEN. You can use the WRITE command with the F$GETSYI lexical function to find the number of contiguous free global pages and free global sections. The following example shows how to get this information at your terminal (the default for SYS$OUTPUT): $ WRITE SYS$OUTPUT F$GETSYI("CONTIG_GBLPAGES") 15848 $ WRITE SYS$OUTPUT F$GETSYI("FREE_GBLSECTS") 24 $ To modify incremental parameters such as GBLPAGES and GBLSECTS, precede the parameter name with ADD_ and supply the incremental value. The following line increases the global page setting by 100: ADD_GBLPAGES = 100 After you make all your changes, exit from the editor. Execute the AUTOGEN procedure to recalculate your system parameters. Enter the following command at the DCL prompt: $ @SYS$UPDATE:AUTOGEN GETDATA REBOOT . . . $ When you specify REBOOT, AUTOGEN performs an automatic system shutdown and then reboots the system. Any users logged in to the system are immediately disconnected during the shutdown. The automatic reboot puts the new parameter values into effect. The AUTOGEN utility automatically adjusts some of the SYSGEN parameters based on the consumption of resources since the last reboot. If you do not want to take advantage of this automatic adjustment or if your system has been running less than 24 hours, include the NOFEEDBACK qualifier on the AUTOGEN command line. For example: 3-10 After Installing Compaq ACMSxp Software $ @SYS$UPDATE:AUTOGEN GETDATA REBOOT NOFEEDBACK . . . $ For more information about using AUTOGEN, see the OpenVMS System Management Subkit. 3.3.5 Setting UCX Parameters for DCE Software DCE software operation on a node requires the following minimum UCX parameter values: ___________________________________________________________ Parameter_____________Value________________________________ Device sockets 600 Large buffers 600 Small_buffers_________2000_________________________________ To correct an inadequate number of UCX device sockets, increase the number of UCX device sockets and small buffers. For example: UCX> SET COMMUNICATION/DEVICE=600 UCX> SET COMMUNICATION/SMALL=(MAXIMUM=2000) UCX> See DCE 1.3 Release Notes for details on setting UCX parameters and DEC TCP/IP Services for OpenVMS System Management for more information on UCX. 3.3.6 Maintaining DECnet Configuration Values The number of servers that can be run on a DECnet Phase IV node is dependent on the parameters shown in Table 3-3. Table_3-3_DECnet_Phase_IV_Parameters_______________________ Parameter__________________Value___________________________ MAX BROADCAST NONROUTER 1023 MAX DECLARED OBJECTS 1023 (continued on next page) After Installing Compaq ACMSxp Software 3-11 Table_3-3_(Cont.)_DECnet_Phase_IV_Parameters_______________ Parameter__________________Value___________________________ MAXIMUM_LINKS_______________240____________________________ The value for MAX BROADCAST NONROUTER is set at the maximum; MAX DECLARED OBJECTS can be a maximum of 16383. Compaq recommends that you set the listed parameters to the values shown. If the Max broadcast nonrouters and Maximum Declared Objects parameters are not set as listed in Table 3-3, you possibly see the DCE error "can't listen socket". 3.3.6.1 Guidelines for Calculating Links DECnet allows a maximum of 960 logical links. This value is reduced to 512 if the alias maximum links is also specified. The default value for maximum links is 32. To determine the maximum number of links that a TPsystem might use, use the following variables: cl_proc Number of client processes l_links Number of logical links p_svrs Number of processing servers p_svrs_proc Number of processing server processes t_svrs Number of task servers If the client processes reside on the same node as the task and processing servers, use the formula in (3-2). l_links = 2(t_svrs*p_svrs*p_svrs_proc)+4(cl_proc*t_svrs) (3-2) For example, if a TPSYSTEM has 5 clients, 3 task servers, 3 processing servers, and 4 processes per processing server, all running on the same node, calculate the number of logical links as in (3-3). l_links = 2(3*3*4)+4(5*3) (3-3) The maximum number of logical links that the TPSYSTEM utilizes in this example is 132. 3-12 After Installing Compaq ACMSxp Software If the client processes reside on different nodes than the task and processing servers, calculate two formulas. o For each each node running client processes, use (3-4). l_links = 2(cl_proc*t_svrs) (3-4) o For the node running the task and processing servers, use (3-5). l_links = 2(t_svrs*p_svrs*p_svrs_proc)+2(cl_proc*t_svrs) (3-5) Using the above example, if the clients are all running on one node, that node requires 30 logical links and the node running the task and processing servers requires 102 logical links. 3.3.7 Maintaining DECnet-Plus Configuration Values To run 20 or more ACMSxp users, increase the NSP MAXIMUM TRANSPORT CONNECTIONS parameter. If this parameter is set too low, applications may fail with RPC connection aborted messages appearing in your ACMSxp default event log file as follows: SEVERITY: error rpc MESSAGE TEXT: connection aborted by local host (dce / rpc) tps MESSAGE TEXT: %%TPS-E-INTFTEMPUNAVAIL, RPC interface temporarily unavailable Use the NCL utility to observe parameters necessary for NSP communications. Use the NCL SHOW directive to examine the NSP maximum transport connections and maximum receive buffers as shown in Example 3-1. Example 3-1 Examining NSP Attributes (continued on next page) After Installing Compaq ACMSxp Software 3-13 Example 3-1 (Cont.) Examining NSP Attributes $ MCR NCL SHOW NODE 0 NSP TRANSPORT MAX TRAN CONN,MAX RECE BUFF Node 0 NSP at 1998-07-09-17:01:59.553-04:00Iinf Characteristics Maximum Transport Connections = 1000 Maximum Receive Buffers = 8000 $ The values for the indicated attributes must be equal to or greater than those shown. If they are not, check the configuration script file at the following location: SYS$MANAGER:NET$NSP_TRANSPORT_STARTUP.NCL Ensure that similar lines having values equal to or greater than the values shown are in the configuration file. SET NODE 0 NSP MAXIMUM TRANSPORT CONNECTIONS 1000 SET NODE 0 NSP MAXIMUM RECEIVE BUFFER 8000 To increase the NSP maximum transport connections parameter and related parameters, proceed as follows: 1. Edit the following file: SYS$STARTUP:NET$NSP_TRANSPORT_STARTUP.NCL 2. Increase the following parameters for the NSP entity: A. Maximum remote NSAPs B. Maximum transport connections Value must be less than the value for maximum remote NSAPs. C. Maximum window Value must be greater than or equal to the number of maximum receive buffers divided by maximum transport connections. D. Maximum receive buffers Value of maximum receive buffers must be eight times the value of the maximum transport connections. 3-14 After Installing Compaq ACMSxp Software The SET commands that set the parameters must precede the line that enables NSP on the node. After editing the startup file, create a backup copy of the file. The system overwrites the file when NET$CONFIGURE.COM is run, so a backup copy should be created. Shut down and restart the network either from the system console or from a LAT connection: 1. Shut down the network by entering: $ @SYS$STARTUP:NET$SHUTDOWN . . . $ 2. Restart the network by entering: $ @SYS$SYSTEM:STARTUP NETWORK . . . $ When the network restarts, the new values are in effect. 3.4 Configuring DECdtm-Journal File and Logical Name To create and start ACMSxp TPsystems and to execute task servers, DECdtm must be running and have a journal file to which it can log transaction information. 3.4.1 Logical Name The logical name SYS$DECDTM_INHIBIT must not be set. Setting this logical name prevents DECdtm from starting. If this logical name is set, deassign it. 3.4.2 Journal File DECdtm requires a journal file with a name in the following format: SYSTEM$nodename.LM$JOURNAL The node name is the DEC/net Phase IV simple name of the node. The file must reside in the SYS$JOURNAL directory. If this file does not exist, no DECdtm calls are successful. After Installing Compaq ACMSxp Software 3-15 If you have DECdtm-related problems, look for the journal file. If none exists, use the Log Manager Control Program (LMCP) to create one, as follows: 1. Run the program with the MCR command. For example: $ MCR LMCP Log Manager Control Program V1.1 LMCP> 2. Use the CREATE command in the following format: CREATE LOGFILE SYS$JOURNAL:SYSTEM$node_name This creates a journal file with an extension of LM$JOURNAL and a default size of 4000 blocks. A suitable file size depends on the expected transaction load. For example, Compaq recommends that a system running ten users, three task servers, and three processing servers start with a journal file of 10 000 blocks: CREATE LOGFILE /SIZE=10000 SYS$JOURNAL:SYSTEM$node_name The command creates the file with the specified size. 3.5 Modifying Node Startup Procedures The installation creates a startup procedure that may be added to the system startup file, SYS$MANAGER:STARTUP_ VMS.COM. For this kit, the startup procedure is: SYS$STARTUP:ACMSXPV032$STARTUP.COM This procedure runs the ACMS_SET_VERSION.COM procedure from the SYSEXE subdirectory where the product is installed. 3.6 VMScluster Considerations If you want to run ACMSxp software on multiple nodes of a VMScluster network, first check to see that you have the appropriate software licenses. After you install ACMSxp software, perform the following steps: 1. Issue the LICENSE LOAD command to activate the appropriate licenses on each node in the VMScluster on which ACMSxp software is to be executed. Refer to OpenVMS License Management Utility Manual. 3-16 After Installing Compaq ACMSxp Software 2. Execute the ACMSXPV032$STARTUP.COM procedure on each node of the VMScluster on which ACMSxp software is to be executed. See Section 3.5. 3. If logged-in users want to use the ACMS and STDL commands, they must log out and log in again or use the DCL SET command: $ SET COMMAND/TABLES=SYS$LIBRARY:DCLTABLES $ The command runs the Command Definition utility to add the ACMSxp commands from the specified command definition table. This step is required. The ACMSxp installation procedure modifies the DCL command table so that the ACMSxp and STDL commands are recognized and processed. However, the previous command table is still in effect for those users who are currently logged in. 4. Execute the following command on all other VMScluster members: $ INSTALL REPLACE SYS$LIBRARY:DCLTABLES $ The command associates the latest version of the DCL tables image with the current known installed image. When these procedures are complete, ACMSxp software is installed clusterwide. 3.6.1 Setting Up a Systemwide Default ACMSxp Version To change a local default version of ACMSxp software (in which each user must run ACMS_SET_VERSION.COM to use) to a systemwide default version (in which all users at login have the same ACMSxp version available), you must: 1. In the ACMSxp startup procedure (located in SYS$STARTUP:) remove the comment from the line that passes the SYSTEM parameter to ACMS_SET_VERSION.COM. 2. Place the comment on the other line invoking ACMS_SET_ VERSION.COM. After Installing Compaq ACMSxp Software 3-17 3. In all other versions of ACMSxp software that you have installed, comment out the line that passes the SYSTEM parameter to ACMS_SET_VERSION.COM and uncomment the other invocation of ACMS_SET_VERSION.COM. Only one ACMSxp version is the system default version. 3.7 Setting Up ACMSxp with Japanese Language Support If you are running on an ACMSxp system with the Japanese language environment, you need to check for the existence of catalog files. If the ACMSxp catalog files do not exist, you need to adjust your environment. Do the following: 1. If you are not running with an ACMSxp systemwide default version (see Section 3.6.1), set the ACMSxp version to the one you installed. 2. Determine the ACMSxp product root directory. The catalog files are found in a language-specific subdirectory of the SYSMSG directory under the ACMSxp root directory to which the ACMS_SYS_DIR logical name points. From the DCL prompt: $ SHOW LOGICAL $ACMS_SYS_DIR "ACMS_SYS_DIR" = "USER1:[ACMSXPV032.SYSEXE]" (LNM$PROCESS_TABLE) $ 3. Look for the ACMSxp message catalogs in the subdirectory for the Japanese language under the SYSMSG directory. $ DIRECTORY USER1:[ACMSXPV032.SYSMSG.JA_JP_SDECKANJI] Directory USER1:[ACMSXPV032.SYSMSG.JA_JP_SDECKANJI] TPS_API_LOCALE.CAT;1 Total of 1 files. $ The ACMSxp catalog files TPS.CAT and TPS_API.CAT should be in this directory. 4. If the files are not in the directory, define a new value for NLSPATH logical name as follows: $ DEFINE NLSPATH "USER1:[ACMSXPV032.SYSMSG.%L]%N,USER1:[ACMSXPV032.SYSMSG.EN_US_ISO8859-1]%N" %DCL-I-SUPERSEDE, previous value of NLSPATH has been superseded $ 3-18 After Installing Compaq ACMSxp Software This setting allows access to the ACMSxp default English-language catalogs. If the files are in the directory, do not change NLSPATH. After Installing Compaq ACMSxp Software 3-19 4 _________________________________________________________________ Deinstalling ACMSxp Software This chapter describes the deinstallation of the ACMSxp software using the ACMS_DEINSTALL.COM command procedure. This process frees up resources for other uses. 4.1 Deinstallation Requirements The ACMS_DEINSTALL.COM procedure requires the following privileges: o CMKRNL-Allows the command procedure to replace the following file and remove known images: SYS$SHARE:DCLTABLES.EXE o SYSNAM-Allows the command procedure to deassign logical names in the system name table o SYSPRV or BYPASS-Allows the command procedure to copy DCLTABLES.EXE to SYS$SHARE Deinstalling either a nondefault or system default installation requires the same privileges. The procedure attempts to acquire all the above privileges. Any privileges acquired by the procedure are released before it completes. To deinstall ACMSxp software, use the ACMS_DEINSTALL.COM procedure found in the [.SYSEXE] product subdirectory. Invoke ACMS_DEINSTALL.COM either directly by using its OpenVMS directory specification or by using the ACMS_SYS_ DIR logical name (if defined). For example: $ @ACMS_SYS_DIR:ACMS_DEINSTALL . . . $ Deinstalling ACMSxp Software 4-1 You must use the OpenVMS directory specification to locate the procedure on a system in which a partial deinstallation was done and ACMSxp logical names are now undefined, or to delete an installation for which the ACMSxp startup procedure has not been run. The deinstallation procedure deletes both system default and nondefault installations and can be invoked before or after ACMS_SET_VERSION.COM has been run. If ACMSxp logical names are defined, those exclusive to ACMSxp are removed and those modified to include information related to ACMSxp have that information removed. All files associated with the installation are then removed from the system, including the deletion procedure itself. If the procedure is unable to delete one or more files, it does not delete itself so that the system manager can correct the problem and rerun the procedure. ACMS_DEINSTALL can delete partially deleted installation trees. Before making any changes, ACMS_DEINSTALL verifies that no TPsystems are present that were created by the installation. Because the procedure uses relative directory specifications, it must remain in the [.SYSEXE] product subdirectory. 4.2 Actions Performed During Deinstallation The deinstallation command procedure does the following: o Checks for stopped and running TP systems The deinstallation procedure checks the ACMS_ TPSYSTEMS.DAT file to see whether TPsystems related to this installation are present, and possibly running. If TPsystems are present, the deinstallation procedure notifies the user that the TPsystems must be stopped (if necessary) and deleted before the deinstallation can continue. The procedure then exits. o Modifies logical names If the logical name ACMS_SYS_DIR is defined and points to the location of the ACMS_DEINSTALL.COM being run, the deinstallation modifies logical names associated with this installation. ACMSxp logical names are defined by the startup procedure associated with each installation. Logical names defined for use exclusively by ACMSxp 4-2 Deinstalling ACMSxp Software software (ACMS_SYS_DIR and ACMS_EXAMPLES_DIR, for example) are undefined by the deinstallation procedure and those that are modified by the startup (NLSPATH, for example) have the information specific to this installation removed. The deinstallation procedure then either redefines the logical name or, if the logical name is empty after the information has been removed, deassigns the logical name. The only way to guarantee that all logical names are correctly set is to log out of the process in which ACMS_SET_VERSION.COM and ACMS_DEINSTALL.COM were run. The procedure searches logical name tables in standard order, so that if you delete a system default version of ACMSxp for which you have also run ACMS_SET_VERSION yourself, ACMS_DEINSTALL considers this to be a local installation and does not modify the logical names in the system table. o Deletes other shared files and images After modifying the logical names, the deinstallation procedure asks whether you want to delete those items shared by any other versions of ACMSxp installed on the system: - Verb deletion from the command table You can remove the verbs related to ACMSxp from the following file: SYS$SHARE:DCLTABLES.EXE. - On-line Help You can delete the ACMSxp online help. Note that all installations of ACMSxp on a system share the same online help. The help describes the latest version of the product. o Deletes files created during kit installation You must install ACMSxp into an empty directory. However, after the installation completes, users can place any files they wish into the product directory tree. ACMS_DEINSTALL.COM deletes only the files and directories that were either installed or created during the installation. An exception is the [.SYSTEST] product subdirectory in which the IVP runs. The deinstallation Deinstalling ACMSxp Software 4-3 procedure deletes all files in [.SYSTEST] and the [.TEMP] and [.WORK] subdirectories under [.SYSTEST], if present. ACMS_DEINSTALL.COM also deletes the most recent version of the startup procedure for the kit from the SYS$STARTUP directory. If another copy of the ACMSxp kit with the same version number has been installed on the system and the startup procedure has been purged, the deinstallation procedure deletes the only copy of the ACMSxp startup procedure. See Section 4.4 for the questions related to these deletions made. 4.3 Rerunning an Incomplete Deinstallation If the deinstallation procedure cannot delete a file, it does not delete itself and can be rerun to delete the remaining files. Make any necessary changes to allow deletion, then rerun the deinstallation procedure. ACMS_ DEINSTALL.COM can be run against a product directory tree in which not all files have been deleted. If ACMS_DEINSTALL.COM cannot delete a file, open or read an existing ACMS_TPSYSTEMS.DAT file, obtain the necessary privileges, or, if you enter a Control Y during deinstallation, the procedure exits with a status of 2. In all other cases, the return status is 1. Each time the procedure runs, it attempts to delete from SYS$STARTUP the most recent version of the startup procedure for this version of ACMSxp. Because the first attempt at running the deinstallation procedure undefines the ACMSxp logical names associated with the kit being deinstalled, you cannot specify the logical name ACMS_ SYS_DIR when invoking the procedure for any subsequent runs. Instead, use the OpenVMS directory specification to point to the procedure. The deinstallation procedure then notifies you that ACMS_SET_VERSION has not been run and asks whether you wish to continue the deinstallation. Answer Yes (see Section 4.4). 4-4 Deinstalling ACMSxp Software 4.4 Questions Asked During Deinstallation The deinstallation procedure can ask several questions. Each question requires a Yes or No answer: ACMS_SET_VERSION has not been run. Continue? If the logical name ACMS_SYS_DIR is not defined, the procedure concludes that ACMS_SET_VERSION has not been run and asks if deinstallation should continue. If you continue, any ACMSxp logical names that are currently defined are not modified. Deleting the type ACMSxp in product-directory Continue? The value type is one of the following: o System default-for an installation that has been set up as the default for the system o Local-for an installation to which a user points by running ACMS_SET_VERSION.COM. The value product-directory is the top-level directory into which this version of ACMSxp software was installed. Delete ACMS and STDL command verbs? The command verbs ACMS and STDL reside in SYS$SHARE:DCLTABLES.EXE. This question is asked whether or not the verbs have already been deleted. These verb definitions are shared by all installed versions of ACMSxp. Answer No if other ACMSxp kits are installed. Delete all ACMSxp on-line help? There is only one set of online help text for all instances of ACMSxp software on a system. If other kits are installed, do not delete online help. This question is asked only if the deinstallation procedure determines that ACMSxp online help is present. Deinstalling ACMSxp Software 4-5 A _________________________________________________________________ Sample ACMSxp Installation The following sample listing shows a complete installation of Compaq ACMSxp software, including running the IVP. $ @sys$update:vmsinstal OpenVMS Alpha Software Product Installation Procedure V7.2 It is 9-JUL-1999 at 16:11 Enter a question mark (?) at any time for help. * Do you want to continue anyway [NO]? y * Are you satisfied with the backup of your system disk [YES]? * Where will the distribution volumes be mounted: dka0:[000000] Enter the products to be processed from the first distribution volume set. * Products: ACMSXPAVME01032 * Enter installation options you wish to use (none): The following products will be processed: ACMSXPAVME01 V3.2 Beginning installation of ACMSXPAVME01 V3.2 at 16:11 %VMSINSTAL-I-RESTORE, Restoring product save set A ... %VMSINSTAL-I-RELMOVED, Product's release notes have been moved to SYS$HELP. ***************************************************************************** Copyright (c) Digital Equipment Corporation 1993, 1999. All rights reserved. Restricted Rights: Use, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth in subparagraph (c) (1) (ii) of DFARS 252.227-7013, or in FAR 52.227-19, or in FAR 52.227-14 Alt. III, as applicable. This software is proprietary to and embodies the confidential technology of Compaq Computer Corporation. Possession, use, or copying of this software and media is authorized only pursuant to a valid written license from Compaq or an authorized sublicensor. ***************************************************************************** Sample ACMSxp Installation A-1 Product: ACMSXP-DEV, ACMSXP-RT Producer: DEC Version: 0.0 Release Date: (NONE) * Does this product have an authorization key registered and loaded? y The installation directory is where the files and images for this release are kept. This directory and its contents may be placed in a disk and directory of your choice. The directory should be on a disk that is always mounted and accessible to all users of ACMSXP V3.2. You must pick a directory that can be used exclusively by ACMSXP V3.2; the directory must be empty or not yet exist. * Where would you like to install ACMSxp [SYS$COMMON:[ACMSxpV032]]: * Do you want to run the IVP after the installation [YES]? * Do you want this to be the system default installation of ACMSxp [YES]? NO In order to run ACMSxp without the sysprv privilege the rights identifier ACMS_START_TPSYSTEM will be added to your system. If ACMSxp is being installed in a cluster and the rightslist.dat file is not shared amongst cluster members then the rights identifier must be created on all other cluster members that will run ACMSxp. You can run the image ACMS_SYS_DIR:ACMS_ADD_IDENTIFIER.EXE to create or recreate the ACMS_START_TPSYSTEM rights identifier. The identifier ACMS_START_TPSYSTEM is used in creating an ACE on the LNM$SYSTEM_DIRECTORY logical name table. This ACE will allow ACMSxp to create logical name tables as needed and attach them to the LNM$SYSTEM_DIRECTORY logical name table. The following example shows how to add this ACE to the LNM$SYSTEM_DIRECTORY logical name table using the ACMS_START_TPSYSTEM identifier. $ SET SECURITY LNM$SYSTEM_DIRECTORY/CLASS=LOGICAL_NAME_TABLE - /ACL=(IDENTIFIER=ACMS_START_TPSYSTEM,ACCESS=WRITE+READ+CREATE) You should place this command in a system startup file such as sylogicals.com or sysecurity.com so that the ACL will be preserved across system reboots. The rights identifier ACMS_START_TPSYSTEM will now be added to your system. %ACMSXP03-I-ADDID, This installation adds an IDENTIFIER named ACMS_START_TPSYSTEM. A-2 Sample ACMSxp Installation The rights identifier ACMS_START_TPSYSTEM will now be granted to the logical name table LNM$SYSTEM_DIRECTORY. This identifier should be granted to those accounts that will start ACMSxp tpsystems using the following command: UAF> GRANT/IDENTIFIER ACMS_START_TPSYSTEM %UAF-I-GRANTMSG, identifier ACMS_START_TPSYSTEM granted to CRAMER The command in this example grants the identifier ACMS_START_TPSYSTEM to the user named Cramer. Cramer becomes the holder of the identifier and any resources associated with it. * Press return to Continue: %ACMSXP03-I-DONEASK, No more questions will be asked . . . ***************************************************************************** This installation takes approximately 10 minutes on a DEC 4000 Model 620. Your installation time will vary accordingly depending on your specific hardware platform ***************************************************************************** After installation, the IVP can be run with @ACMS_SYS_DIR:ACMS_RUN_IVP Sample ACMSxp Installation A-3 %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.EXAMPLES]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.EXAMPLES.AVERTZ_VM]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.EXAMPLES.STD]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.EXAMPLES.STD_TPC]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.EXAMPLES.AVERTZ_VR]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.EXAMPLES.EMPLOYEE]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.EXAMPLES.EMPLOYEE.SERVER]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.EXAMPLES.EMPLOYEE.CLIENT]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.SYSEXE]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.SYSHLP]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.SYSLIB]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.SYSMGR]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.SYSMSG]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.SYSMSG.EN_US_ISO8859-1]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.SYSMSG.JA_JP_SDECKANJI]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.SYSTEST]. %VMSINSTAL-I-SYSDIR, This product creates system disk directory SYS$COMMON:[ACMSXPV032.SYSTEST.PRECOMPILED_FILES]. %VMSINSTAL-I-RESTORE, Restoring product save set B ... %VMSINSTAL-I-RESTORE, Restoring product save set C ... %VMSINSTAL-I-RESTORE, Restoring product save set D ... Please add the following line to SYS$MANAGER:SYSTARTUP_VMS.COM @SYS$STARTUP:ACMSXPV032$STARTUP.COM A-4 Sample ACMSxp Installation *************************************************************** * If this installation is performed on a cluster, for each * * cluster node on which you want to run ACMSxp, you must: * * Load an ACMSxp license * * Run the ACMSxp startup procedure * * $ INSTALL REPLACE SYS$LIBRARY:DCLTABLES * *************************************************************** %VMSINSTAL-I-MOVEFILES, Files will now be moved to their target directories... ACMSxp V3.2 for OpenVMS Alpha Copyright (c) 1993, 1999 by Digital Equipment Corporation. All Rights Reserved. Using ACMSxp in OKEEFE$DKA0:[SYS0.SYSCOMMON.ACMSXPV032] ================================================================================ ACMSxp V3.2-1 for OpenVMS Alpha Installation Verification Procedure beginning at 9-JUL-1998 16:14:50 ================================================================================ Setting up logicals... ACMSxp V3.2-1 for OpenVMS Alpha Copyright (c) 1993, 1999 by Digital Equipment Corporation. All Rights Reserved. Setting logicals succeeded. Checking current process quotas... Current process quota check succeeded. Cleaning namespace directory... IVP namespace directory cleaning succeeded. Cleaning work directory... IVP work directory cleaning succeeded. Checking disk space... Disk space check succeeded. Creating ACMSADMIN symbols file... ACMSADMIN symbols file creation succeeded. Creating IVP TP system... IVP TP system creation succeeded. Building IVP server images... IVP server Images build succeeded. Starting IVP TP system... IVP TP system start succeeded. Sample ACMSxp Installation A-5 Creating IVP servers... IVP server creation succeeded. Starting IVP servers... IVP server start succeeded. Checking IVP server running status... Invoking ACMS Client... Stopping IVP servers... IVP servers stopping succeeded. Deleting IVP servers... IVP servers deletion succeeded. Stopping IVP TP system... IVP TPsystem stopping succeeded. Deleting IVP TP system... IVP TP system deletion succeeded. Cleaning namespace directory... IVP namespace directory cleaning succeeded. Cleaning IVP work directory... IVP work directory cleaning succeeded. ================================================================================ ACMSxp V3.2-1 for OpenVMS Alpha IVP completed successfully at 9-JUL-1999 16:18:08 ================================================================================ Installation of ACMSXP V3.2-1 completed at 16:18 Adding history entry in VMI$ROOT:[SYSUPD]VMSINSTAL.HISTORY Creating installation data file: VMI$ROOT:[SYSUPD]ACMSXP032.VMI_DATA Enter the products to be processed from the next distribution volume set. * Products: exit VMSINSTAL procedure done at 16:19 $ When the installation procedure is done, refer to Compaq ACMSxp Developing and Managing Applications for procedures to set up ACMSxp security and configure the ACMSxp system and your STDL applications. A-6 Sample ACMSxp Installation B _________________________________________________________________ ACMSxp-Supplied Files This appendix lists the files that are created in subdirectories of the ACMSxp root directory you supply during the ACMSxp installation. Directory SYS$COMMON:[ACMSXPV032] EXAMPLES.DIR SYSLIB.DIR SYSTEST.DIR SYSEXE.DIR SYSMGR.DIR SYSHLP.DIR SYSMSG.DIR B.1 Examples Directory Directory SYS$COMMON:[ACMSXPV032.EXAMPLES] AVERTZ_VM.DIR STD.DIR;1 AVERTZ_VR.DIR STD_TPC.DIR;1 EMPLOYEE.DIR Directory SYS$COMMON:[ACMSXPV032.EXAMPLES.AVERTZ_VM] CONTROL_WKSP.STDL;1 VM_CREATE_APPL_DB.COM;1 EDIT.COM;1 VM_CREATE_SERVERS.COM;1 LINK_OPTIONS.OPT;1 VM_CREATE_TPSYSTEM.COM;1 LIST_CONTROL_WKSP.STDL;1 VM_DELETE_SERVERS.COM;1 RO_CONTEXT.SQL;1 VM_DELETE_TPSYSTEM.COM;1 RW_CONTEXT.SQL;1 VM_DELETE_WORK_DIR_FILES.COM;1 VEHICLES_ARRAY_WKSP.STDL;1 VM_DESCRIP.MMS;1 VEHICLES_WKSP.STDL;1 VM_DISPLAY_TASK.STDL;1 VM_ADD_TASK.STDL;1 VM_FORM.IFDL;1 VM_BUILD_SERVERS.COM;1 VM_GET_LIST_PROC.SCO;1 ACMSxp-Supplied Files B-1 VM_GET_VEHICLE_PROC.SCO;1 VM_RUN_DEMO.TXT;1 VM_INDEXES.SQL;1 VM_SCHEMA.SQL;1 VM_INVOKE_TASK.COM;1 VM_SETUP_LOGICALS.COM;1 VM_LIST_TASK.STDL;1 VM_START_SERVERS.COM;1 VM_LOAD_VEHICLES.SCO;1 VM_START_TPSYSTEM.COM;1 VM_MENU_FORM.IFDL;1 VM_STOP_SERVERS.COM;1 VM_MENU_TASK.STDL;1 VM_STOP_TPSYSTEM.COM;1 VM_MENU_WKSP.STDL;1 VM_STORE_VEHICLE_PROC.SCO;1 VM_MODIFY_TASK.STDL;1 VM_TASK_GROUP.STDL;1 VM_MSG_GROUP.STDL;1 VM_UPDATE_VEHICLE_ PROC.SCO;1 VM_PROC_GROUP.STDL;1 VM_VEHICLES.DAT;1 VM_RO_PROC_GROUP.STDL;1 VM_WAIT.COM;1 VM_RUN_DEMO.COM;1 Directory SYS$COMMON:[ACMSXPV032.EXAMPLES.AVERTZ_VR] CUSTOMERS_WKSP.STDL;1 RESERVATIONS_WKSP.STDL;1 CU_ARRAY_WKSP.STDL;1 RS_ARRAY_WKSP.STDL;1 DESTINATION_WKSP.STDL;1 SITES_WKSP.STDL;1 EDIT.COM;1 SI_ARRAY_WKSP.STDL;1 HIST_RW_CONTEXT.SQL;1 VEHICLES_WKSP.STDL;1 HIST_WKSP.STDL;1 VEHICLE_RENTAL_HISTORY_ WKSP.STDL;1 LINK_OPTIONS.OPT;1 VE_RO_CONTEXT.SQL;1 RENTAL_CLASSES_WKSP.STDL;1 VE_RW_CONTEXT.SQL;1 RENT_RO_CONTEXT.SQL;1 VR_CANCEL_RS_PROC.SCO;1 RENT_RW_CONTEXT.SQL;1 VR_CHECKIN_TASK.STDL;1 VR_CHECKOUT_TASK.STDL;1 VR_DESCRIP.MMS;1 VR_CHECK_VE_AVAIL_PROC.SCO;1 VR_DO_CKOUT_OR_CNCL_ TASK.STDL;1 VR_CHECK_VE_AVAIL_TASK.STDL;1 VR_FIND_CU_PROC.SCO;1 VR_COMPLETE_CHECKIN_PROC.SCO;1 VR_FIND_CU_TASK.STDL;1 VR_COMPLETE_CHECKOUT_PROC.SCO;1 VR_FIND_RS_CU_TASK.STDL;1 VR_COMPUTE_BILL_PROC.COB;1 VR_FIND_RS_TASK.STDL;1 VR_CONTROL_WKSP.STDL;1 VR_FIND_SI_PROC.SCO;1 VR_COUNT_RS_PROC.SCO;1 VR_FIND_SI_TASK.STDL;1 VR_COUNT_RS_TASK.STDL;1 VR_FIND_VE_PROC.SCO;1 VR_CUSTOMERS.DAT;1 VR_FIND_VE_TASK.STDL;1 B-2 ACMSxp-Supplied Files VR_FORM.IFDL;1 VR_LOAD_CUSTOMERS.SCO;1 VR_GETRESV_TASK.STDL;1 VR_LOAD_RENTAL_ CLASSES.SCO;1 VR_GET_RESV_CU_PROC.SCO;1 VR_LOAD_SITES.SCO;1 VR_GET_RESV_PROC.SCO;1 VR_LOAD_VEHICLES.SCO;1 VR_GET_VE_DATA_PROC.SCO;1 VR_MENU_FORM.IFDL;1 VR_GET_VE_DATA_TASK.STDL;1 VR_MENU_TASK.STDL;1 VR_GET_VE_HIST_PROC.SCO;1 VR_MENU_WKSP.STDL;1 VR_GET_VE_HIST_TASK.STDL;1 VR_MOD_VE_AVAIL_PROC.SCO;1 VR_HISTORY_DB.COM;1 VR_MOD_VE_AVAIL_TASK.STDL;1 VR_HIST_PROC_GRP.STDL;1 VR_MSG_GRP.STDL;1 VR_RENTALS_DB.COM;1 VR_STORE_CU_TASK.STDL;1 VR_RENTALS_INDEX.COM;1 VR_UPDATE_RS_TASK.STDL;1 VR_RENTAL_CLASSES.DAT;1 VR_VEHICLES.DAT;1 VR_RENT_TASK_GRP.STDL;1 VR_VEHICLES_DB.COM;1 VR_RESERVE_TASK.STDL;1 VR_VEHICLES_INDEX.COM;1 VR_RESV_TASK_GRP.STDL;1 VR_VE_RO_PROC_GRP.STDL;1 VR_RS_RO_PROC_GRP.STDL;1 VR_VE_RW_PROC_GRP.STDL;1 VR_RS_RW_PROC_GRP.STDL;1 VR_VE_TASK_GRP.STDL;1 VR_RUN_DEMO.COM;1 VR_WRITE_HIST_RECORD_ PROC.SCO;1 VR_SITES.DAT;1 VR_WRITE_RS_PROC.SCO;1 VR_STORE_CU_PROC.SCO;1 VR_WRITE_RS_TASK.STDL;1 Directory SYS$COMMON:[ACMSXPV032.EXAMPLES.EMPLOYEE] CLIENT.DIR;1 SERVER.DIR;1 Directory SYS$COMMON:[ACMSXPV032.EXAMPLES.EMPLOYEE.CLIENT] EMPL_UWC.C;1 EMPL_UWC.H;1 EMPL_UWC.MMS;1 Directory SYS$COMMON:[ACMSXPV032.EXAMPLES.EMPLOYEE.SERVER] ADMIN_SETUP.COM;1 EMPLOYEE_SERVER_RDB.MMS;1 CONTROL_RECORD.STDL;1 EMPLOYEE_SETUP.COM;1 EMPLOYEE_MSG_GRP.STDL;1 EMPLOYEE_SETUP_RDB.SQL;1 EMPLOYEE_PROCS_RDB.SC;1 EMPLOYEE_TASKS.STDL;1 EMPLOYEE_PROC_GRP.STDL;1 EMPLOYEE_TASK_GRP.STDL;1 EMPLOYEE_RECORD.STDL;1 OPTIONS.OPT;1 Directory SYS$COMMON:[ACMSXPV032.EXAMPLES.STD] ACMSxp-Supplied Files B-3 CREATE_ORACLE_DB.COM;1 STD14.COM;1 CREATE_ORACLE_DB.SQL;1 STD15.COM;1 EMPLOYEE.H;1 STD16.COM;1 EMPLOYEE_RDB.H;1 STD18.COM;1 LINK_OPTIONS.OPT;1 STD19.COM;1 PROFILE.H;1 STD20.COM;1 PROFILE_RDB.H;1 STD3.COM;1 READ_ME_VMS.TXT;1 STD3A_UWC_UWP.C;1 STD.MMS;1 STD4.COM;1 STD10.COM;1 STD5.COM;1 STD6.COM;1 STD_PROC_COB.STDL;1 STD6A.COM;1 STD_PROC_DEC_COB.STDL;1 STD6_UWC_UWP.C;1 STD_PROC_SVR_A.STDL;1 STD7.COM;1 STD_PROC_SVR_B.STDL;1 STD8.COM;1 STD_RDB_SQL.SC;1 STD9.COM;1 STD_READ_SQL.SCO;1 STD_COBOL.COB;1 STD_SETUP.COM;1 STD_CWP.STDL;1 STD_SQL.SC;1 STD_FORMS.IFDL;1 STD_TASK_GROUPS.STDL;1 STD_MT_UWC.C;1 STD_TASK_GROUPS_A.STDL;1 STD_TASK_GROUPS_B.STDL;1 STD_WAIT.COM;1 STD_TASK_SVR.STDL;1 STD_WKSP_DEF.COB;1 STD_TASK_SVR_A.STDL;1 STD_WKSP_DEF.STDL;1 STD_TASK_SVR_B.STDL;1 STD_WRITE_SQL.SCO;1 STD_UWC.C;1 UWC_LINK_OPTIONS.OPT;1 STD_UWP.C;1 Directory SYS$COMMON:[ACMSXPV032.EXAMPLES.STD_TPC] STD_CLEAN_UP.COM;1 STD_SHUTDOWN.COM;1 STD_SETUP_TPC.COM;1 STD_STARTUP.COM;1 B.2 Executable Directory Directory SYS$COMMON:[ACMSXPV032.SYSEXE] B-4 ACMSxp-Supplied Files ACMS$SERVER_STARTUP.COM;1 ACMS_FIND_SYSTEM_MSG.COM;1 ACMS$SERVER_STARTUP.DBG;1 ACMS_IDENTS.COM;1 ACMS.EXE;1 ACMS_LIST_PROCESSES.COM;1 ACMSADMIN.EXE;1 ACMS_PRINT_MSGS.COM;1 ACMS_ADD_IDENTIFIER.EXE;1 ACMS_PRODUCT_BANNER.TXT;1 ACMS_CREATE_TPSYSTEM.COM;1 ACMS_PRODUCT_VERSION.TXT;1 ACMS_DEINSTALL.COM;1 ACMS_QUEUE_SVR.EXE;1 ACMS_DELETE_TPSYSTEM.COM;1 ACMS_QUEUE_SVR.IDF;1 ACMS_EVENT_SVR.EXE;1 ACMS_QUOTA.COM;1 ACMS_EVENT_SVR.IDF;1 ACMS_RECQU_SVR.EXE;1 ACMS_RECQU_SVR.IDF;1 ACMS_START_TPSYSTEM.COM;1 ACMS_RSEND_SVR.EXE;1 ACMS_VERIFY_PRINCIPAL.EXE;1 ACMS_RSEND_SVR.IDF;1 CATMSG.EXE;1 ACMS_RUN_IVP.COM;1 GUI_KIT_INTEL.EXE;1 ACMS_SEND_ERRORS_1_0.IDF;1 GUI_KIT_README_INTEL.TXT;1 ACMS_SETUP_CDB.EXE;1 GWLOG.EXE;1 ACMS_SETUP_TPSYSTEM.EXE;1 STDL.EXE;1 ACMS_SET_VERSION.COM;1 TPS_SMI_LITERAL.CAT;1 ACMS_SHOW_ENVIRONMENT.COM;1 TPS_SVR_ACMSDEBUG.EXE;1 B.3 Help Directory Directory SYS$COMMON:[ACMSXPV032.SYSHLP] ACMSADMIN_HELP.HLB;1 ACMSXP_MGT_CONFIG_ CHAP.TXT;1 ACMSXP_ERROR_MESSAGES.TXT;1 STDL-HELP.HLP;1 ACMSXP_MGT_CONFAPPS_CHAP.TXT;1 B.4 Library Directory Directory SYS$COMMON:[ACMSXPV032.SYSLIB] ECLASS.COB;1 STDL_SRTL$SHAREV032.EXE;1 ECLASS.H;1 STDL_SYSTEM_WKSP.STDL;1 EINFO.COB;1 STDL_SYSTEM_WKSP_X.STDL;1 EINFO.H;1 STDL_XOPEN$SHAREV032.EXE;1 FORMSDEF.H;1 TPS$SHAREV032.EXE;1 FORMS_DEF.H;1 TPS.H;1 MC_DCL.CLD;1 TPS_CDB.H;1 STDLDEFS.H;1 TPS_CFE.H;1 STDL_MIA$SHAREV032.EXE;1 ACMSxp-Supplied Files B-5 TPS_COMMON.H;1 TPS_PS_IDL.H;1 TPS_COMMON_IDL.H;1 TPS_PTHREAD.H;1 TPS_COMMON_IDL.IDL;1 TPS_PTHREAD_EXC.H;1 TPS_COS.H;1 TPS_QUE.H;1 TPS_EVT.H;1 TPS_REC.H;1 TPS_FIL.H;1 TPS_REC_AGENT.H;1 TPS_LST.H;1 TPS_RPC.H;1 TPS_MSG.H;1 TPS_RPC_APINFO_IDL.H;1 TPS_PS.H;1 TPS_RPC_APINFO_IDL.IDL;1 TPS_PS_DECFORMS.H;1 TPS_RPC_CONTEXT.H;1 TPS_RPC_CONTEXT.IDL;1 TPS_STDL.H;1 TPS_RQS.H;1 TPS_STDL.IDL;1 TPS_RQS_INVOKE.H;1 TPS_SVR.H;1 TPS_RQS_TYPES.H;1 TPS_TAS.H;1 TPS_SEC.H;1 TPS_TXN.H;1 TPS_SHM.H;1 TPS_TXN_GW_IDL.H;1 TPS_SI.H;1 TPS_TXN_GW_IDL.IDL;1 TPS_SI_I18N.H;1 TPS_TXN_RPC_IDL.H;1 TPS_SM.H;1 TPS_TXN_RPC_IDL.IDL;1 TPS_SMA.H;1 TPS_VDB.H;1 TPS_SRTL.H;1 TPS_WRM.H;1 B.5 Manager Directory Directory SYS$COMMON:[ACMSXPV032.SYSMGR] ACMS_TEST_TPC_READY.EXE;1 TPCONTROLLER.EXE;1 B.6 Messages Directory Directory SYS$COMMON:[ACMSXPV032.SYSMSG] EN_US_ISO8859-1.DIR;1 JA_JP_SDECKANJI.DIR;1 Directory SYS$COMMON:[ACMSXPV032.SYSMSG.EN_US_ISO8859-1] TPS.CAT;1 TPS_API_LOCALE.CAT;1 TPS_API.CAT;1 Directory SYS$COMMON:[ACMSXPV032.SYSMSG.JA_JP_SDECKANJI] TPS_API_LOCALE.CAT;1 B-6 ACMSxp-Supplied Files B.7 Test Directory Directory SYS$COMMON:[ACMSXPV032.SYSTEST] ACMS_IVP.COM;1 CREATE_IVP_SERVERS.COM;1 ACMS_IVP_RUN.TXT;1 CREATE_IVP_ TPSYSTEM.COM;1 BUILD_IVP_IMAGES.COM;1 DELETE_IVP_FILES.COM;1 CHECK_COBOL_DATA.COM;1 DELETE_IVP_SERVERS.COM;1 CHECK_PROCESSES.COM;1 DELETE_IVP_SYMBOLS.COM;1 CHECK_SQL_DATA.COM;1 DELETE_IVP_ TPSYSTEM.COM;1 CLEAN_NAMESPACE.COM;1 EMPLOYEE.H;1 CREATE_IVP_ACMSADMIN_SYMBOLS.COM;1 IVP_COBOL_PROC.COB;1 CREATE_IVP_APPL_DB.COM;1 IVP_FORMS.IFDL;1 CREATE_IVP_APPL_DB.SQL;1 IVP_LINK_OPTIONS.OPT;1 IVP_SQL.SC;1 SAVE_TPSYSTEMS.COM;1 IVP_TASK_SVR_A.STDL;1 SETUP_IVP.COM;1 IVP_TASK_SVR_A_NOCOBOL.STDL;1 START_IVP_SERVERS.COM;1 IVP_UWP_SVR.C;1 START_IVP_TPSYSTEM.COM;1 IVP_UW_CLIENT.C;1 STOP_IVP_SERVERS.COM;1 IVP_WKSP_DEF.STDL;1 STOP_IVP_TPSYSTEM.COM;1 OBTAIN_TID.C;1 STOP_PROCESSES.COM;1 PRECOMPILED_FILES.DIR;1 SUBMIT_ACMS_TASK.COM;1 PROFILE.H;1 VERIFY_DISK_SPACE.COM;1 RUN_ACMS_CLIENT.COM;1 VERIFY_PRIVS.COM;1 RUN_UW_CLIENT.COM;1 VERIFY_QUOTAS.COM;1 Directory SYS$COMMON:[ACMSXPV032.SYSTEST.PRECOMPILED_FILES] IVP_FORMS_CWP.OBJ;1 IVP_TASK_GRP_A_1_0.IDF;1 IVP_PROC_GRP_A_1_0.IDF;1 IVP_TASK_GRP_A_CLI.OBJ;1 IVP_PROC_GRP_A_CLI.OBJ;1 IVP_TASK_GRP_A_SVR.OBJ;1 IVP_PROC_GRP_A_SVR.OBJ;1 IVP_TASK_SVR_A.OBJ;1 IVP_PROC_GRP_B_1_0.IDF;1 IVP_TASK_SVR_A_ NOCOBOL.OBJ;1 IVP_PROC_GRP_B_CLI.OBJ;1 IVP_WKSP_DEF.H;1 IVP_PROC_GRP_B_SVR.OBJ;1 IVP_WKSP_DEF_NOEPV.H;1 ACMSxp-Supplied Files B-7 _________________________________________________________________ Index A______________________________ B______________________________ Account BIOLM, 3-4 cell_admin, 1-8 BYTLM, 3-4, 3-5 DCE for IVP, 1-10 SYSTEM, 2-1 C user _______________________________ IVP access, 1-11 cell_admin account, 1-8 privileges, 3-3 CHANNELCNT, 1-3 process quotas, 3-4 Cluster requirements, 3-3 ACMSxp considerations, 3-16 acmsxp_svr account Companion software option, 3-3 creation, 1-10 Compiler IVP access, 1-11 virtual memory, 3-5 ACMS_CREATE_TPSYSTEM Connections user accounts to run, 3-3 configuring, 3-13 ACMS_DEINSTALL CPU, 3-4 running, 4-1 ACMS_DELETE_TPSYSTEM D______________________________ user accounts to run, 3-3 DCE software ACMS_START_TPSYSTEM UCX parameter values, 3-11 rights identifier, 1-2, 2-6 Debugger user accounts to run, 3-3 kit requirement, 1-6 Alternate working device version check, 1-6 VMSINSTAL option, 2-3 DECdtm ASTLM, 3-4 configuring, 3-15 Audit records DECnet BYTLM quota, 3-5 configuration, 3-11 Autoanswer links calculation, 3-12 VMSINSTAL option, 2-2 NSP values, 3-13 AUTOGEN setting parameters, 3-11 running, 3-9 system parameter for DECnet- Plus, 3-8 Index-1 Deinstall actions, 4-2 H______________________________ questions, 4-5 Help directory, B-5 requirements, 4-1 rerunning, 4-4 I DIOLM, 3-4 _______________________________ Directory Installing ACMSxp root, B-1 error recovery, 2-9 Disk privilege required, 1-2 space required, 1-4 required order, 1-5 system back-up, 2-1 sample, A-1 to A-6 stages, 2-3 E______________________________ starting, 2-1 ENQLM, 3-4 verification, 2-8 Error IVP recovery, 2-9 actions performed, 2-8 Examples directory, B-1 DCE procedures, 1-8 Executable directory, B-4 log files, 2-9 privilege required, 1-2 running standalone, 2-9 F______________________________ File J______________________________ ACMSxp-supplied, B-1 to B-7 Journal file DECdtm journal, 3-15 creation, 3-16 MODPARAMS.DAT, 3-9 DECdtm, 3-15 VMSINSTAL autoanswer, 2-2 JTQUOTA, 3-4 FILLM, 3-4 G K______________________________ _______________________________ KSTACKPAGES, 3-8 GBLPAGES, 1-3 changing, 3-9 L GBLSECTIONS, 1-3 _______________________________ changing, 3-9 Library directory, B-5 GUI Links installing management, 3-1 guidelines for calculating procedures, 3-2 maximum, 3-12 Japanese system, 3-3 LMCP prerequisite software, 3-1 journal file creation, 3-16 software option Log companion, 3-3 VMSINSTAL option, 2-3 standalone, 3-3 system requirements, 3-2 gui_kit_intel.exe file, 3-2 Index-2 M______________________________ O______________________________ Management software option Operating system See GUI required components, 1-6 Manager directory, B-6 required patches, 1-7 MAXACCTJOBS, 3-4 MAXDETACH, 3-5 P______________________________ MAXJOBS, 3-5 Page file quota, 3-5 Messages directory, B-6 PAK MIN_PQL_DASTLM, 1-3 See Product authorization key MIN_PQL_DBIOLM, 1-3 Parameter MIN_PQL_DBYTLM, 1-3 changing, 3-9 MIN_PQL_DCPULM, 1-3 checking system, 3-8 MIN_PQL_DDIOLM, 1-3 incremental, 3-10 MIN_PQL_DENQLM, 1-3 Patches MIN_PQL_DFILLM, 1-3 required OS, 1-7 MIN_PQL_DJTQUOTA, 1-3 PBYTLM, 3-5 MIN_PQL_DPGFLQUOTA, 1-3 PGFLQUO, 3-5 MIN_PQL_DPRCLM, 1-3 Physical I/O pages parameter MIN_PQL_DTQELM, 1-4 queuing, 3-7 MIN_PQL_MASTLM, 1-4 PIOPAGES, 3-7 MIN_PQL_MBIOLM, 1-4 PRCLM, 3-5 MIN_PQL_MBYTLM, 1-4 PRIO, 3-5 MIN_PQL_MCPULM, 1-4 Privilege MIN_PQL_MDIOLM, 1-4 installing ACMSxp, 1-2 MIN_PQL_MENQLM, 1-4 running IVP, 1-2 MIN_PQL_MFILLM, 1-4 user accounts, 3-3 MIN_PQL_MJTQUOTA, 1-4 Product authorization key MIN_PQL_MPGFLQUOTA, 1-4 installing, 1-1 MIN_PQL_MPRCLM, 1-4 VMSINSTAL question, 2-5 MIN_PQL_MTQELM, 1-4 MODPARAMS.DAT location, 3-9 Q______________________________ QUEPRIO, 3-5 N______________________________ Queuing NET$DECLAREOBJECT physical I/O pages parameter rights identifier, 1-2 requirement, 3-7 NSP Quotas configuration, 3-13 ACMSxp commands, 3-4, 3-5 changing, 3-5 minimum process, 3-4 Index-3 TPsystem (cont'd) R______________________________ BYTLM for starting, 3-5 Request queue server TQELM, 3-5 working set parameters, 3-8 Tuning, 3-7 Rights identifier physical I/O pages parameter ACMS_START_TPSYSTEM, 1-2, queuing, 3-7 2-6 system parameters, 1-3 NET$DECLAREOBJECT, 1-2 checking, 3-8 Root alternate DECnet-Plus, 3-8 VMSINSTAL option, 2-3 UCX parameters, 3-11 _______________________________ U______________________________ Saveset UAF temporary storage, 2-3 change, 3-5 Server UAF quotas, 3-4 account requirements, 3-3 UCX parameters, 3-11 setting parameters for, 3-11 setup.exe program, 3-2 V______________________________ SHRFILLM, 3-5 Version Software setting systemwide, 3-17 optional layered, 1-8 Virtual memory limit exceeded, required layered, 1-2 3-5 Standalone software option, VMSINSTAL 3-3 options, 2-2 Startup parameters, 2-2 modifying node, 3-16 sample, A-1 SYS$DECDTM_INHIBIT logical starting, 2-1 name, 3-15 SYSGEN W______________________________ running, 3-8 WSDEF, 3-5 System parameter WSEXTENT, 3-5, 3-8 running ACMSxp, 1-3 WSQUO, 3-5, 3-8 System parameters tuning, 3-7 DECnet-Plus, 3-8 T______________________________ TCP/IP UCX parameters, 3-11 Test directory, B-7 TPsystem account requirements create or delete, 3-3 starting, 3-3 Index-4