DIGITAL OpenVMS Disk Services for_Windows_NT______________________________________ Installing July 1997 Revision/Update Information: This is a new manual. Software Versions: DIGITAL OpenVMS Disk Services for Windows NT Version 1.0 OpenVMS Alpha Version 7.1 Windows NT Version 4.0 ________________________________________________________________ July 1997 Possession, use, or copying of the software described in this documentation is authorized only pursuant to a valid written license from Digital or an authorized sublicensor. While Digital believes the information included in this publication is correct as of the date of publication, it is subject to change without notice. Digital Equipment Corporation makes no representations that the use of its products in the manner described in this publication will not infringe on existing or future patent rights, nor do the descriptions contained in this publication imply the granting of licenses to make, use, or sell equipment or software in accordance with the description. © Digital Equipment Corporation 1997. All Rights Reserved. The following are trademarks of Digital Equipment Corporation: DIGITAL, OpenVMS, VAX DOCUMENT, and the DIGITAL logo. The following are third-party trademarks: Intel is a registered trademark of Intel Corporation. Windows NT is a trademark of Microsoft Corporation. All other trademarks and registered trademarks are the property of their respective holders. This document was prepared using VAX DOCUMENT, Version 2.1. _________________________________________________________________ Contents Welcome................................................... v 1 Installing the Server Component 1.1 Before You Install the Server Component....... 1-1 1.1.1 Check Prerequisite Hardware and Software.................................. 1-1 1.1.2 Back Up Your System Disk.................. 1-1 1.2 Installing the Server Component............... 1-2 1.3 After You Install the Server Component........ 1-3 1.3.1 Register and Load the PAK................. 1-3 1.3.2 Enable the NTDS Help Message Database..... 1-4 1.3.3 Install DIGITAL TCP/IP Services for OpenVMS ECO#6............................. 1-4 1.3.4 Configure DIGITAL TCP/IP Services for OpenVMS................................... 1-5 1.3.5 Reboot.................................... 1-5 2 Installing the Client Component 2.1 Before You Install the Client Component....... 2-1 2.1.1 Check Prerequisite Hardware and Software.................................. 2-1 2.1.2 Install the Server Component.............. 2-1 2.2 Installing the Client Component............... 2-2 2.3 After You Install the Client Component........ 2-2 iii A Files Installed on Your System iv _________________________________________________________________ Welcome About This Book DIGITAL[TM] OpenVMS[TM] Disk Services for Windows NT[TM] consists of: o A server component running on OpenVMS Alpha o A client component running on Windows NT This book describes how to install both the server component and the client component. Prerequisite Hardware and Software The following table shows the hardware and software that you need to install Version 1.0 of DIGITAL OpenVMS Disk Services for Windows NT. v ___________________________________________________________ OpenVMS_Alpha____________Windows_NT________________________ An Alpha system that: A Windows NT server or workstation o Is running OpenVMS (Intel[R] or Alpha CPU) that: Alpha Version 7.1 o Is running Windows NT Version o Is running DIGITAL 4.0, with TCP/IP installed TCP/IP Services for o Has at least 8 MB of free disk OpenVMS Version 4.1 space with the TIMA kit ECO#6 + installed o Has at least 40,000 free blocks on its system disk +This TIMA kit is included in the kit for Version 1.0 of DIGITAL OpenVMS Disk Services for Windows NT, and is placed in SYS$UPDATE when you install the server component of DIGITAL_OpenVMS_Disk_Services_for_Windows_NT.______________ For More_Information_____________________________________________ For_information_on...__See_the...__________________________ Setting up and Guide to DIGITAL OpenVMS Disk managing Services for Windows NT Restrictions and Release Notes for DIGITAL OpenVMS known_problems_________Disk_Services_for_Windows_NT________ vi 1 _________________________________________________________________ Installing the Server Component This chapter describes how to install the server component for Version 1.0 of DIGITAL OpenVMS Disk Services for Windows NT. It contains the following sections: o Before You Install the Server Component o Installing the Server Component o After You Install the Server Component 1.1 Before You Install the Server Component This section describes the tasks you must perform before you install the server component of DIGITAL OpenVMS Disk Services for Windows NT: o Check Prerequisite Hardware and Software o Back Up Your System Disk 1.1.1 Check Prerequisite Hardware and Software Check that your OpenVMS Alpha system: o Is running OpenVMS Alpha Version 7.1 o Is running DIGITAL TCP/IP Services for OpenVMS Version 4.1 o Has at least 40,000 free blocks on its system disk 1.1.2 Back Up Your System Disk A failure during installation could leave your system disk in an inconsistent state. DIGITAL recommends that you back up your system disk before starting the installation. Use the backup procedures that are established at your site. Installing the Server Component 1-1 Installing the Server Component 1.2 Installing the Server Component 1.2 Installing the Server Component To install the server component of DIGITAL OpenVMS Disk Services for Windows NT, follow these steps: 1. Log in to an account that has full privileges enabled, for example, the SYSTEM account. 2. Enter the PRODUCT INSTALL command; use the /SOURCE qualifier to specify the directory that contains the kit, DEC-AXPVMS-NTDS-V0100--1.PCSI. For example: $ PRODUCT INSTALL NTDS /SOURCE=DAD10:[NTDS010.KIT] See the DCL help for the PRODUCT command to find out about the features it provides, such as how to control where the product is installed (by default, SYS$COMMON), and how to extract the Release Notes before you start the installation. When you enter the PRODUCT INSTALL command, you will see a message like this: The following product has been selected: DEC AXPVMS NTDS V1.0 Layered Product [Available] Do you want to continue? [YES] 3. Press Return to answer Yes (the default). The installation starts: Configuration phase starting ... You will be asked to choose options, if any, for each selected product and for any products that may be installed to satisfy software dependency requirements. DEC AXPVMS NTDS V1.0: DIGITAL OpenVMS Disk Services for Windows NT © Digital Equipment Corporation 1997. All rights reserved. Digital Equipment Corporation This product uses the PAK NTDS-DISK Do you want the defaults for all options? [YES] 4. Press Return to answer Yes (the default). The installation continues: Do you want to review the options? [NO] 1-2 Installing the Server Component Installing the Server Component 1.2 Installing the Server Component 5. Press Return to answer No (the default). The installation continues: Execution phase starting ... The following product will be installed: DEC AXPVMS NTDS V1.0 Layered Product Portion done: 0%...10%...30%...40%...80%...90%...100% The following product has been installed: DEC AXPVMS NTDS V1.0 Layered Product DEC AXPVMS NTDS V1.0: DIGITAL OpenVMS Disk Services for Windows NT See the Installation Guide for information on post installation tasks. 1.3 After You Install the Server Component This section describes the tasks you must perform after you have installed the server component of DIGITAL OpenVMS Disk Services for Windows NT: o Register and Load the PAK o Enable the NTDS Help Message Database o Install DIGITAL TCP/IP Services for OpenVMS ECO#6 o Configure DIGITAL TCP/IP Services for OpenVMS o Reboot 1.3.1 Register and Load the PAK DIGITAL OpenVMS Disk Services for Windows NT is a layered product that is separate from the OpenVMS operating system. To use it, you must register its Product Authorization Key (PAK) in your license database. To do this, follow these steps: 1. Purchase the NTDS-DISK PAK from your DIGITAL sales representative. 2. Register the NTDS-DISK PAK, using the OpenVMS License Management Facility (LMF): $ @SYS$UPDATE:VMSLICENSE Installing the Server Component 1-3 Installing the Server Component 1.3 After You Install the Server Component 3. Use the LICENSE MODIFY command with the /RESERVE qualifier to register the Windows NT computers that will be allowed to connect to disk services on your OpenVMS Cluster. List the names of the computers, for example: $ LICENSE MODIFY NTDS-DISK /RESERVE=(NTSYSTEM1,NTSYSTEM2) The number of computers you specify in this list must not exceed the number of activity units available in your PAK. 4. Use the LICENSE LOAD command to load the NTDS-DISK PAK on all the OpenVMS Alpha nodes that you want to be able to provide disk services to Windows NT clients: $ LICENSE LOAD NTDS-DISK 1.3.2 Enable the NTDS Help Message Database Enable the NTDS help message database so that you can use the HELP /MESSAGE command to get help on the error messages returned by NTDS commands. To do this, define the logical name MSGHLP$LIBRARY to point to the NTDS help message database, SYS$HELP:NTDS.MSGHLP$DATA. If the logical name MSGHLP$LIBRARY is not currently defined, edit SYS$MANAGER:SYLOGICALS.COM to add the following line, which defines it to point to both the main OpenVMS help message database and the NTDS help message database: $ DEFINE MSGHLP$LIBRARY SYS$HELP:MSGHLP$LIBRARY.MSGHLP$DATA, - SYS$HELP:NTDS.MSGHLP$DATA /SYSTEM /EXECUTIVE_MODE If the logical name MSGHLP$LIBRARY is currently defined, change the current definition to include SYS$HELP:NTDS.MSGHLP$DATA in the search list. Edit whichever startup file or database currently defines the logical name during system startup. 1.3.3 Install DIGITAL TCP/IP Services for OpenVMS ECO#6 If you have not already done so, install the DIGITAL TCP/IP Services for OpenVMS Version 4.1 ECO#6 kit. This kit was copied to SYS$UPDATE:DEC-AXPVMS-UCXECO_41_6-V0600--4.PCSI when you installed the server component in the previous section. 1-4 Installing the Server Component Installing the Server Component 1.3 After You Install the Server Component 1.3.4 Configure DIGITAL TCP/IP Services for OpenVMS Configure DIGITAL TCP/IP Services for OpenVMS on all the OpenVMS Alpha nodes that you want to be able to provide disk services to Windows NT clients: 1. Make sure that DIGITAL TCP/IP Services for OpenVMS has at least one interface configured with an IP address. For information on how to do this, see the documentation for DIGITAL TCP/IP Services for OpenVMS. 2. Make sure that DIGITAL TCP/IP Services for OpenVMS is configured to run the PWIP driver. Use the UCX$CONFIG command procedure to check that the PWIP driver is enabled: $ @SYS$MANAGER:UCX$CONFIG Select "Optional components" on the main menu, then "Configure PWIP Driver" on the Optional Components Configuration menu. 3. To optimize the performance of DIGITAL OpenVMS Disk Services for Windows NT, we recommend that you use the following command to set the TCP protocol parameters in the UCX configuration database: $ UCX SET CONFIGURATION PROTOCOL TCP /NODELAY_ACK 1.3.5 Reboot Reboot to activate DIGITAL OpenVMS Disk Services for Windows NT. If your OpenVMS Cluster has a single system disk, reboot all the OpenVMS Alpha nodes that you want to be able to provide disk services to Windows NT clients. If your OpenVMS Cluster has multiple system disks: 1. Install DIGITAL OpenVMS Disk Services for Windows NT on your other system disks. 2. Reboot all the OpenVMS Alpha nodes that you want to be able to provide disk services to Windows NT clients. Installing the Server Component 1-5 2 _________________________________________________________________ Installing the Client Component This chapter describes how to install the client component for Version 1.0 of DIGITAL OpenVMS Disk Services for Windows NT. It contains the following sections: o Before You Install the Client Component o Installing the Client Component o After You Install the Client Component 2.1 Before You Install the Client Component This section describes the tasks you must perform before you install the client component of DIGITAL OpenVMS Disk Services for Windows NT: o Check Prerequisite Hardware and Software o Install the Server Component 2.1.1 Check Prerequisite Hardware and Software Your Windows NT system can have either an Intel or Alpha CPU and can be either a server or a workstation. It must: o Be running Windows NT Version 4.0, with TCP/IP installed o Have at least 8 MB of free disk space 2.1.2 Install the Server Component Follow the instructions in Chapter 1 to install the server component on OpenVMS Alpha. Installing the Client Component 2-1 Installing the Client Component 2.2 Installing the Client Component 2.2 Installing the Client Component To install the client component of DIGITAL OpenVMS Disk Services for Windows NT, follow these steps: 1. If you have not already done so, install TCP/IP on the Windows NT computer and set up the TCP/IP network configuration. TCP/IP is included with Windows NT, but you may have chosen not to install it. If so, install and configure it now. 2. When you installed DIGITAL OpenVMS Disk Services for Windows NT on the OpenVMS Alpha system in Chapter 1, the installation procedure created a self-extracting file SYS$UPDATE:NTDS010.EXE. Copy SYS$UPDATE:NTDS010.EXE to a temporary directory on the Windows NT computer. If you use FTP, set the transfer type to binary before you copy the file. 3. Log on to the Windows NT computer as an Administrator and double click on NTDS010.EXE, then follow the instructions on the screen to unzip the file and run the Setup Program for DIGITAL OpenVMS Disk Services for Windows NT. 2.3 After You Install the Client Component The Setup Program gives you the option of restarting your computer to activate the software. If you did not select this option, remember to restart your computer before you try to use DIGITAL OpenVMS Disk Services for Windows NT. Now read the Guide to DIGITAL OpenVMS Disk Services for Windows NT to find out how to set up and manage disk services. 2-2 Installing the Client Component A _________________________________________________________________ Files Installed on Your System The installation procedure creates the following files on your OpenVMS Alpha system: [SYS$LDR]SYS$NTDS.EXE [SYS$LDR]SYS$NTDS.STB [SYS$STARTUP]NTDS$INSTALL_IMAGES.COM [SYS$STARTUP]NTDS$SHUTDOWN.COM [SYS$STARTUP]NTDS$STARTUP.TEMPLATE [SYSEXE]NTDS.EXE [SYSEXE]NTDS_SERVER.EXE [SYSHLP]NTDS.MSGHLP$DATA [SYSHLP]NTDS$HELP.HLB [SYSHLP]NTDS010.RELEASE_NOTES [SYSHLP]NTDS010_GUIDE.PS [SYSLIB]NTDS$SDA.EXE [SYSUPD]DEC-AXPVMS-UCXECO_41_6-V0600--4.PCSI [SYSUPD]NTDS.CLD [SYSUPD]NTDS010.EXE [SYSUPD]PROVIDE_NTDS.COM [SYSUPD]REMOVE_NTDS.COM The installation procedure modifies the following files on your OpenVMS Alpha system: [SYS$LDR]VMS$SYSTEM_IMAGES.DATA [SYSHLP]HELPLIB.HLB [SYSLIB]DCLTABLES.EXE [SYSUPD]VMS$SYSTEM_IMAGES.IDX Files Installed on Your System A-1