HP OpenVMS Systems Documentation

Compaq TCP/IP Services for OpenVMS
Management Command Reference

SHOW CFS

Displays statistical information about OpenVMS and container file systems.
The NFS server software must be active.
Related commands: SHOW NFS

Format

SHOW CFS [ /CONTINUOUS[=n] ]
[ /PARAMETERS ]
[ /SUMMARY ]

Qualifiers

/CONTINUOUS[=n]
Optional. Default: Static display; /CONTINUOUS=4.
Continuously updates the screen display.
To terminate the display, press Ctrl/Z.
/PARAMETERS
Optional.
Displays the parameters.
/SUMMARY
Optional.
Displays the following information:
Wait states
Data cache performance
Summary of allocated services and resources

Examples

TCPIP> SHOW CFS


    CFS Services                       OpenVMS Services
-------------------     ----------------------------------------------
CLOSE            14
CREATE_FH         1     $ASSIGN       17    $QIO                     0
CREDIR_FH         1     $DASSGN       15         Access             14
FREEBUFF          0                              Create              2
GETATTR       16256     $DEQ         125         Deaccess           15
LINK_FH           0     $ENQ         436
LOOKUP_FH        14                              Read_attr        6746
OPEN_FH          14     getVMpage      6         Write_attr          7
READ           8119     freeVMpage     0
READBUFF          0                              Lookup             57
READDIR_FH       13     $CLREF     26318
READLINK_FH       0     $SETEF     26318         Extend              1
REMDIR_FH         1
REMOVE_FH         2     $DCLAST    26325         Delete              3
RENAME_FH         2     $CLRAST     1877         Enter               2
SETATTR           1     $SETAST    49601         Remove              2
STATFS         1873
SYMLINK_FH        0     $GETDVI     1875         Read_V             13
WRITE             5                              Write_V             2
OTHER             6     $CHKPRO       71
TOTAL         26322

TCPIP> SHOW CFS /SUMMARY

        CFS Service status and performance    29-OCT-1998 14:54:36.74

Service State   Cur  Max  Total  Cacheop  Cur  Hit  I/O  Inc    Status
-------------   ---  ---  -----  -------  ---  ---  ---  ---  ----------
FP-Access         0    0     0   Read       0    0    0    0  Clusize 16
FP-Attributes     0    0     0   Read-A     0    0    0    0  Limit  256
FP-Delete         0    0     0   Write      0    0    0    0  Inuse    0
FP-Dir            0    0     0   Write-A    0    0    0    0  Busy     0
FP-Rename         0    0     0   Write-D    0                 Hitrate  0
  FP Sub_total    0    0     0
Buffered          0    0     0   Nameop   Cur  Hit     Status
Internal          0    0     0   ------  ---- ----  -------------
I/O               0    0     0   Add        0       Tabsize     0
Lock              0    0     0   Delete     0       Inuse       0
Logging           0    0     0   Lookup     0    0  Hitrate     0
Resource          0    0     0
RMS               0    0     0   Fileop   Cur  Hit     Status
Service           0    0     0   ------  ---- ----  -------------
Timer             0    0     0   Find       0    0  Limit       0
Other             0    0     0   Find-A          0  Inuse  655535
Synch             0    0     0   Find-C          0  Timeout     5
                                                    Hitrate     0

Services count    1    1     3   ATCBs:  1 TBABs:  0 RDCBs: 1 Pages:  0

Displays service wait states, data cache performance, and a summary of services and resources.

TCPIP> SHOW CFS /PARAMETERS

                         CFS PARAMETERS

     Data cache
        Size             256
        Low limit        4
        High limit       8

     Attribute cache     Disabled
        Size             0
        Timeout          5

     Name cache          Disabled
        Size             0

     Transfer size       8192
     Write size          512

     Output fatal messages to device: _OPA0:

Displays file system information.

SHOW COMMUNICATION

Displays the settings and status for the IP, TCP, UDP, and INET_ACP software, including routing, buffers, sockets, and memory on the running system.
Related commands: SET COMMUNICATION

Format

SHOW COMMUNICATION [ /MEMORY ]
[ /ROUTE ]
[ /SECURITY ]

Qualifiers

/MEMORY
Optional.
Displays information about memory allocated to data structures associated with network operations.
/ROUTE
Optional.
Displays routing statistics.
/SECURITY
Optional.
Displays the security settings specified with the following SET COMMUNICATION qualifiers:

/ACCEPT
/REJECT

Examples

#1
TCPIP> SHOW COMMUNICATION/ROUTE Route statistics Created by redirects 0 Modified by redirects 0 Wildcarded lookups 6 Invalid redirect calls 0 Failed lookups 0

Displays routing statistics.

TCPIP> SHOW COMMUNICATION /MEMORY
1585 mbufs in use:
        490 mbufs allocated to data
        221 mbufs allocated to ancillary data
        2 mbufs allocated to packet headers
        131 mbufs allocated to socket structures
        198 mbufs allocated to protocol control blocks
        180 mbufs allocated to routing table entries
        246 mbufs allocated to socket names and addresses
        21 mbufs allocated to socket options
        76 mbufs allocated to interface addresses
        1 mbufs allocated to kernel table
        2 mbufs allocated to ip multicast options
        7 mbufs allocated to ip multicast address
        10 mbufs allocated to interface multicast addess
        1 mbufs allocated to <mbuf type 100>
        1 mbufs allocated to <mbuf type 108>
        3 mbufs allocated to <mbuf type 109>
        7 mbufs allocated to <mbuf type 112>
        28 mbufs allocated to <mbuf type 113>
        28 mbufs allocated to <mbuf type 114>
        3 mbufs allocated to <mbuf type 115>
        3 mbufs allocated to <mbuf type 117>
        5 mbufs allocated to <mbuf type 118>

Displays information about memory usage.

TCPIP> SHOW COMMUNICATION /SECURITY

Communication Security Parameters

Allow Log:  Acpt Actv Dactv Conn Error Exit Logi Logo Mdfy Rjct TimO Addr
Force Log:  None

Security device:  disabled

Access lists
 Accept host: 0.0.0.0
 Accept netw: 0.0.0.0

Displays information about security parameters that were specified with the SET COMMUNICATION command.

SHOW CONFIGURATION

Displays the information in the configuration database. This database, read by the TCP/IP Services startup procedure, holds information to:

Configure the lower-layer protocols, including dynamic routing.
Configure and enable the Internet interfaces.
Configure the services you want enabled when TCP/IP Services starts up.
Configure the BIND resolver.
Configure the BIND server, including the default domain.
Configure SMTP.
Configure SNMP.
Configure TIME.
Map file systems.

Because the SET CONFIGURATION commands do not take effect until the next time TCP/IP Services starts up, the SHOW CONFIGURATION command might not display the current settings for the running software. For example, the information you see from SHOW CONFIGURATION PROTOCOL might differ from the SHOW PROTOCOL /PARAMETERS output.
Related commands: All SET CONFIGURATION commands

Format

SHOW CONFIGURATION { component
ENABLE SERVICE [service]
START ROUTING }
[ /COMMON ]
[ /FULL ]
[ /OUTPUT=file ]

Parameters

component
Required if you do not specify ENABLE SERVICE or START ROUTING.
Component, defined in the configuration database, whose configuration you want to display.
ENABLE SERVICE [service]
Required if you do not specify component or START ROUTING.
Displays either the specified component or all the components that are enabled by the TCP/IP Services startup procedure.
START ROUTING
Required if you do not specify component or ENABLE SERVICE.
Shows whether or not routing is configured to start running by the TCP/IP Services startup procedure.

Qualifiers

/COMMON
Optional. Default: Node specific.
Valid only with SHOW CONFIGURATION ENABLE SERVICE.
Displays the information in the configuration database for the clusterwide enabling or disabling of services.
/FULL
Optional. The default is to give a brief listing of the information.
Displays complete information.
Use with the component parameter.
/OUTPUT=file
Optional. Default: Screen display.
Writes output to the specified file.

Examples

#1
TCPIP> SHOW CONFIGURATION ENABLE SERVICE Enable service FTP, FTP_CLIENT, LPD, MOUNT, NFS, NFS_CLIENT, PCNFS, PORTMAPPER, REXEC, RSH, SMTP, SNMP

Displays the services configured in the services database that will be enabled by the TCP/IP Services startup procedure.

TCPIP> SHOW CONFIGURATION SNMP
SNMP Configuration

Flags:    AuthenTraps Sets

Contact:  Sam Spade

Location
  First:  Falcon Building
  Second: Los Angeles, California

Community           Type       Address_list

public              Read       0.0.0.0

trapit              Read Trap  136.20.0.10

trapit2             Read Trap  136.20.0.12, 136.20.0.15

rw2                 Read Write 136.20.0.15, 136.20.0.100

Displays the SNMP configuration.

#3
TCPIP> SHOW CONFIGURATION NAME_SERVICE BIND Resolver Configuration Transport: UDP Domain: fred.parrot.brd.com Retry: 4 Timeout: 4 Servers: 11.20.208.10, 11.20.208.53 Path: No values defined TCPIP>

Displays, from the configuration database, the BIND resolver configuration.

#4
TCPIP> SHOW CONFIGURATION INTERFACE Interface: DE1 IP_Addr: 11.20.208.100 NETWRK: 255.255.0.0 BRDCST: 11.20.255.255 Interface: LO0 IP_Addr: 137.0.0.1 NETWRK: 255.0.0.0 BRDCST: TCPIP>

Displays the permanent definition of Internet interfaces DE1 and LO0.

TCPIP> SHOW CONFIGURATION SMTP


SMTP Configuration
                                                                   Options
Initial interval:   0 00:30:00.00       Address_max:    16       NOEIGHT_BIT
Retry interval:     0 01:00:00.00       Hop_count_max:  16       NORELAY
Maximum interval:   3 00:00:00.00                                TOP_HEADERS

Timeout             Initial       Mail    Receipt       Data  Terminate
  Send:                   5          5          5          3         10
  Receive:                5

Alternate gateway:  not defined
General gateway:    not defined

Substitute domain:  not defined
Zone:               not defined

Postmaster:         TCPIP_SMTP
Log file:           SYS$SPECIFIC:[TCPIP$SMTP]TCPIP$SMTP_LOGFILE.LOG

Generic queue       Queues   Participating nodes

TCPIP$SMTP_CRANE_00     1     CRANE

Displays the SMTP configuration.

SHOW CONFIGURATION PROTOCOL

Displays information in the configuration database which sets the parameters for ICMP, IP, TCP, and UDP when TCP/IP Services starts up.
Related commands: SET CONFIGURATION PROTOCOL, SET PROTOCOL

Format

SHOW CONFIGURATION PROTOCOL [ protocol ]
[ /PARAMETERS ]

Parameters

protocol
Optional. Default: All protocols.
Specify one of the following: ICMP, IP, TCP, UDP.

Qualifiers

/PARAMETERS
Optional.
Shows parameter settings. You can specify any protocol.

Examples

TCPIP> SHOW CONFIGURATION PROTOCOL



ICMP
  Redirect:               enabled
  Unreachable:           disabled

IP
  Forward:               disabled

  Reassembly timer:             0

TCP
  Delay ACK:              enabled
  Window scale:           enabled
  Drop count:                   0
  Probe timer:                  0

                          Receive                Send

  Push:                  disabled            disabled
  Quota:                        0                   0

UDP
  Unpriv. broadcast:     disabled

                          Receive                Send

  Checksum:               enabled             enabled
  Quota:                        0                   0

Displays information in the configuration database.

SHOW DEVICE_SOCKET

Displays:

Device socket counters
Current settings from the running communications software

(A device socket is composed of two parts: the internet device (interface) and the socket.)

Format

SHOW DEVICE_SOCKET [ device_socket ]
[ /CONTINUOUS[=n] ]
[ /FULL ]
[ /HOST=host ]
[ /[NO]LOCAL ]
[ /PORT=n ]
[ /SERVICE=service ]
[ /TYPE=socket_type ]

Parameters

device_socket
Optional. Default: All device sockets.
Device socket for which you want information.
Specify the characters BG and the device's unit number, for example, BG3, BG17.

Qualifiers

/CONTINUOUS[=n]
Optional. Default: Static display; /CONTINUOUS=4.
Automatically updates the display.
Screen update interval in seconds. Valid only for a specific device socket.
To terminate the display, press Ctrl/C.
/FULL
Optional. The default is to give a brief listing of the information.
Displays complete information, including:

Application option settings, for example, ACCEPT or FULL_DUPLEX_CLOSE
State of the service
Counters for receiving and sending buffers

/HOST=host
Optional. Default: All hosts.
Displays information for device sockets bound to the specified host.
This does not include device sockets bound to the "ANY host" (address 0.0.0.0).
/LOCAL

/NOLOCAL
Optional. Default: /LOCAL.
Displays information for device sockets bound to hosts in the local hosts database.
/NOLOCAL: Displays information for device sockets bound to hosts in the hosts database and hosts known by the BIND resolver.
/PORT=n
Optional. Default: All local ports.
Displays information for device sockets bound to the specified local port.
/SERVICE=service
Optional. Default: All services.
Displays information for device sockets used for the specified service.
/TYPE=socket_type
Optional. Default: /TYPE=ALL.
Displays information for the specified type of device socket. Specify one of the following:

STREAM
DGRAM

Examples

TCPIP> SHOW DEVICE_SOCKET BG21 /FULL


Device_socket:  BG21        Type: STREAM
                      LOCAL                          REMOTE
         Port:           21                               0
         Host:  *                               *
      Service:  FTP

                                                           RECEIVE       SEND
                                   Queued I/O                    0             0
       Q0LEN         0             Socket buffer bytes           0             0
       QLEN          0             Socket buffer quota       61440         61440
       QLIMIT     1024             Total buffer alloc            0             0
       TIMEO         0             Total buffer limit       491520        491520
       ERROR         0             Buffer or I/O waits           1             0
       OOBMARK       0             Buffer or I/O drops           0             0
                                   I/O completed                 0             0
                                   Bytes transferred             0             0

  Options:  ACCEPT REUSEADR
  State:    PRIV
  RCV Buff: WAIT
  SND Buff: None

Displays complete information about device socket BG21, including the options that are set, for example, the FULL_DUPLEX_CLOSE option.
(With the FULL_DUPLEX_CLOSE option set, the first data transmission on a TCP connection that has been closed by the remote application returns an EPIPE error. Subsequent send operations on the half-closed socket proceed normally.)
The following table describes the counters in the first column of the display.

Counter Meaning

Q0LEN Number of sockets that are about to be connected to the specified socket

QLEN Number of sockets that have established a connection but have not yet been accepted by the specified socket

QLIMIT Number of sockets for the Q0LEN and QLEN sockets

TIMEO Not used

ERROR Error code temporarily stored on the socket

OOBMARK Out-of-band mark

#2
TCPIP> SHOW DEVICE_SOCKET BG75 /CONTINUOUS=10

Displays information about device socket BG75 every 10 seconds.

#3
TCPIP> SHOW DEVICE_SOCKET /HOST="lark"

Displays information about all device sockets for remote host lark .

#4
TCPIP> SHOW DEVICE_SOCKET BG1898 Port Remote Device_socket Type Local Remote Service Host bg1898 STREAM 23 2568 TELNET 16.20.176.227

Displays socket type, service, and host information for device BG1898.

SHOW EXPORT

Displays disks/directories available for mounting by NFS clients, in the form of UNIX path names. It also displays the clients allowed to mount these path names.
Related commands: ADD EXPORT, REMOVE EXPORT, MAP, SET CONFIGURATION MAP, SET CONFIGURATION NOMAP, SHOW MAP, SHOW CONFIGURATION MAP

Format

SHOW EXPORT [ "/path/name" ]
[ /HOST=host ]
[ /OUTPUT=file] ]

restrictions

Requires read access to the export database.

Parameters

"/path/name"
Optional. Default: All exported file systems.
Exported files for which to show access rights.
To specify multiple directory names, separate them with slashes.

Qualifiers

/HOST="host_name"
Optional. Default: All hosts.
NFS client hosts for which you want to display access rights.
/OUTPUT=file
Optional. Default: Screen display. Sends output to the specified file.

Examples

TCPIP> SHOW EXPORT

File system                Host name

/TOUCAN                    TOUCAN, toucan
/talkers                   parrot
/aviary_dua0               *
/condor_root/root          condor
/condor_root/work4         condor
/nene_d                    *
/nfstest_unix/lark1        *
/nfstest_unix/lark2        *
/spoonbill                 dove, nuthatch, dove.tree.branch.com
                           toucan, oriole.tree.branch.com
/spoonbill/birdy           dove, DOVE, nuthatch, thrush,
                           thrush.tree.branch.com
/spoonbill/bigbirdy        dove

Displays exported NFS file systems with the clients that have access rights.

#2
TCPIP> SHOW EXPORT/HOST="condor" File System Host name /condor_root/root condor /condor_root/work4 condor

Displays exported NFS file systems for clients on host CONDOR.

Contents

Index

HP OpenVMS Systems Documentation

Compaq TCP/IP Services for OpenVMSManagement Command Reference

SHOW CFS

Format

Qualifiers

/CONTINUOUS[=n]

/PARAMETERS

/SUMMARY

Examples

SHOW COMMUNICATION

Format

Qualifiers

/MEMORY

/ROUTE

/SECURITY

Examples

SHOW CONFIGURATION

Format

Parameters

component

ENABLE SERVICE [service]

START ROUTING

Qualifiers

/COMMON

/FULL

/OUTPUT=file

Examples

SHOW CONFIGURATION PROTOCOL

Format

Parameters

protocol

Qualifiers

/PARAMETERS

Examples

SHOW DEVICE_SOCKET

Format

Parameters

device_socket

Qualifiers

/CONTINUOUS[=n]

/FULL

/HOST=host

/LOCAL

/NOLOCAL

/PORT=n

/SERVICE=service

/TYPE=socket_type

Examples

SHOW EXPORT

Format

restrictions

Parameters

"/path/name"

Qualifiers

/HOST="host_name"

/OUTPUT=file

Examples

Compaq TCP/IP Services for OpenVMS
Management Command Reference