;This ADF file is compatable only with the programmed Memory version
; of the 800E/2 which is the production version

AdapterID 050CEh

AdapterName  "800E/2 NIC"

NumBytes 1


nameditem
	Prompt	"I/O, RAM, EPROM"


;Selections with boot ROM enabled

     Choice "1000H, 0CC000H, 0CA000H"

	  pos[0]=XX00000Xb
	  io 1000h-101fh
	  mem 0CA000H-0CFFFFH


     Choice "2020H, 0CC000H, 0CA000H"

	  pos[0]=XX00001Xb
	  io 2020H-203FH
	  mem 0CA000H-0CFFFFH


     Choice "8020H, 0C8000H, 0CC000H"

	  pos[0]=XX00010Xb
	  io 8020H-803FH
	  mem 0C8000H-0CDFFFH


     Choice "0A0A0H, 0C8000H, 0CC000H"

	  pos[0]=XX00011Xb
	  io 0A0A0h-0A0BFh
	  mem 0C8000H-0CDFFFH


     Choice "0B0B0H, 0D0000H, 0D4000H"

	  pos[0]=XX00100Xb
	  io 0B0B0H-0B0CFh
	  mem 0D0000H-0D5FFFH


     Choice "0C0C0H, 0D0000H, 0D4000H"

	  pos[0]=XX00101Xb
	  io 0C0C0h-0C0DFh
	  mem 0D0000H-0D5FFFH


     Choice "0C3D0H, 0C4000H, NONE"

	  pos[0]=XX00110Xb
	  io 0C3D0h-0C3FFh
	  mem 0C4000H-0C7FFFH


     Choice "1000H, 0D4000H, NONE"

	  pos[0]=XX01000Xb
	  io 1000h-101fh
	  mem 0D4000H-0D7FFFH


     Choice "2020H, 0D4000H, NONE"

	  pos[0]=XX01001Xb
	  io 2020H-203FH
	  mem 0D4000H-0D7FFFH


     Choice "8020H, 0D8000H, 0DC000H"

	  pos[0]=XX01010Xb
	  io 8020H-803FH
	  mem 0D8000H-0DDFFFH

     Choice "0A0A0H, 0D8000H, 0DC000H"

	  pos[0]=XX01011Xb
	  io 0A0A0h-0A0BFh
	  mem 0D8000H-0DDFFFH

     Choice "0B0B0H, 0DC000H, 0DA000H"

	  pos[0]=XX01100Xb
	  io 0B0B0H-0B0CFh
	  mem 0DA000H-0DFFFFH


     Choice "0C0C0H, 0DC000H, 0DA000H"

	  pos[0]=XX01101Xb
	  io 0C0C0h-0C0DFh
	  mem 0DA000H-0DFFFFH



;Selections with boot ROM disabled

     Choice "1000H, 0CC000H, Disable"

	  pos[0]=XX10000Xb
	  io 1000h-101fh
	  mem 0CC000H-0CFFFFH


     Choice "2020H, 0CC000H, Disable"

	  pos[0]=XX10001Xb
	  io 2020H-203FH
	  mem 0CC000H-0CFFFFH


     Choice "8020H, 0C8000H, Disable"

	  pos[0]=XX10010Xb
	  io 8020H-803FH
	  mem 0C8000H-0CBFFFH


     Choice "0A0A0H, 0C8000H, Disable"

	  pos[0]=XX10011Xb
	  io 0A0A0h-0A0BFh
	  mem 0C8000H-0CBFFFH


     Choice "0B0B0H, 0D0000H, Disable"

	  pos[0]=XX10100Xb
	  io 0B0B0H-0B0CFh
	  mem 0D0000H-0D3FFFH


     Choice "0C0C0H, 0D0000H, Disable"

	  pos[0]=XX10101Xb
	  io 0C0C0h-0C0DFh
	  mem 0D0000H-0D3FFFH


     Choice "8020H, 0D8000H, Disable"

	  pos[0]=XX11010Xb
	  io 8020H-803FH
	  mem 0D8000H-0DBFFFH

     Choice "0A0A0H, 0D8000H, Disable"

	  pos[0]=XX11011Xb
	  io 0A0A0h-0A0BFh
	  mem 0D8000H-0DBFFFH

     Choice "0B0B0H, 0DC000H, Disable"

	  pos[0]=XX11100Xb
	  io 0B0B0H-0B0CFh
	  mem 0DC000H-0DFFFFH


     Choice "0C0C0H, 0DC000H, Disable"

	  pos[0]=XX11101Xb
	  io 0C0C0h-0C0DFh
	  mem 0DC000H-0DFFFFH

Help

"The I/O address range shown are the addresses at which the adapter
will decode for the adapter's control i/o.

The RAM address block is decoded for the use of a data transfer buffer.

The EPROM address block is decoded for the use of a remote
boot EPROM.  This optionn may be disabled."




nameditem
	Prompt	"Interrupt level"

     Choice "IRQ 3"

     pos[0]=00XXXXXXb
     int 3

     Choice "IRQ 5"
     pos[0]=01XXXXXXb
     int 5

     Choice "IRQ 10"
     pos[0]=10XXXXXXb
     int 10

     Choice "IRQ 15"
     pos[0]=11XXXXXXb
     int 15


Help

"The IRQ selection assigns which interrupt
request line the lan adapter will use to
signal the microprocessor via the interrupt
controller."