Hi,
Thanks to All who replied, Alan_at_nabeth came the
closest, suggest scsi cable problem.
I had to perform process of elimination, first
replaced ba356 shelf, then I/O module, no effect.
Replacing the cable took care of the problem.
_Richard.
--- Tru64 User <tru64user_at_yahoo.com> wrote:
> Greetings,
> I have stumbled in my last process of disk upgrades.
> Replacing 9.1 gb drives with 18.2, disk types
> rz1ed-vw
> and rz1ef-vw are used.
> I have total of 6 shelfs, controlled by a single
> hsz50.
> 4 shelfs have been replaced already...some with
> RZ1ED-VW exclusively, and some with RZ1EF-VW
> exclusively.
> All 4 raids (raid 5, 7 disks/raid) are completely
> ok.
>
> Trying to add another raid5, similar to above, but
> it
> fails from the start. I replaced the old disks
> (tried
> both rz1ed and rz1ef disks), then ran "run config",
> takes a while, then errors out, and complains of a
> totally different port.
>
> What I have done:
> 1. switched disks types, from rz1ed->rz1ef (I
> already
> have same types working on same shelf raidsets)
>
> 2. Tried adding disks manually (Gives:Warning 9030:
> Cannot determine if the correct device type is at
> the
> PTL)....and thus show disk gives:
>
> HSZ> show disk100
>
> Name Type Port Targ
> Lun
> Used by
>
------------------------------------------------------------------------------
>
> DISK100 disk 1 0
> 0
> Misconfigured: No device at this PTL,
> please
> see user guide
> HSZ>
>
>
> then went ahead and created a raidset, and tried to
> initialize, gave error no device installed at this
> PTL.
> so just delete the disks again.
>
> 3. unmountd FS's, then performed a controller
> restart.
> Didn't help.
>
> 4. Checked the service manual (unfortunately i have
> one for v5.1), and there is no corrective action
> (00)
> given for the instance code below.
>
> Error below complaining on unit 205, unit 205 is
> online and working without any problems. However,
> just
> to see if the specific disk is to be blame, i
> deleted
> the disk at PTL 5 3 0 (disk530), and replaced it,
> but
> error remains the same.
> One other thing I have noticed from below, it shows
> the disk type is RZ1EF-CB, while drives are marked
> outside as ending in VW. They are all good drives,
> have been working before on an hsz70.
> Any ideas are welcomed.
>
>
>
> Exact output:
>
> Firmware Version: V57Z (00)
> Informational Report
> Unit Number: 205. (00CD)
> Unit Software Version: 1.(01) Unit Hardware Version:
> 49. (31)
> Retry Level: 1. Retires: 1.
> Port:5. Target: 3. LUN: 0.
> SCSI Device Type: 0.(00)
> Device ID: "RZ1EF-CB (C) DEC" Device Serial Number:
> "0D6265GK"
> Device Firmware Revision Level: "0371"
> SCSI Command Opcode: 42.(2A)
> Sense Data Qualifiers: 0.(00)
> SCSI Sense Data:
> Error Code: 112.(70) {current command execution}
> Information field is valid
> Segment: 0.(00)
> Sense Key: 11.(0B) ABORTED COMMAND
> ILI: 0 EOM: 0 FM: 0
> Information: 70862007
> Additional Sense Length: 10.(0A)
> Command-Specific Information: 00000000
> ASC: 0.(00) ASCQ: 6.(06)
> FRU: 0.(00) Sense-Key Specific: 00000
> Instance Code: 0258000A
> HSZ>
>
> ......resets and spits out the output below:
> %EVL--HSZ> --13-JAN-1946 04:59:15 (time not set) --
> Instance Code: 03F40064
> Template: 65. (41)
> Power On Time: 4. Years, 127. Days, 19. Hours, 13.
> Minutes, 6. Seconds
> Controller Model: HSZ50-AX
> Serial Number: ZG71525894 Hardware Version: A01 (01)
> Firmware Version: V57Z (00)
> Informational Report
> Port: 1. Target 6.
> Instance Code: 03F40064
> HSZ>
>
> the PTL i am trying to add disks are 110-->160.
>
> _Thanks in advance.
> Richard
>
>
>
>
>
> =====
>
>
> __________________________________________________
> Do You Yahoo!?
> NEW from Yahoo! GeoCities - quick and easy web site
> hosting, just $8.95/month.
> http://geocities.yahoo.com/ps/info1
=====
__________________________________________________
Do You Yahoo!?
Make a great connection at Yahoo! Personals.
http://personals.yahoo.com
Received on Tue Oct 09 2001 - 20:34:05 NZDT