UPDATE:: Is there a way of updating the hardware database ?

From: Boddy Bill - bboddy <bboddy_at_acxiom.co.uk>
Date: Tue, 11 Feb 2003 17:29:53 +0000

I already have had a few suggestions to basically run " hwmgr -scan scsi " ,
however I have tried this and it never picks up the new IDENT.............




 -----Original Message-----
From: Boddy Bill - bboddy [mailto:bboddy_at_acxiom.co.uk]
Sent: Tuesday, February 11, 2003 5:16 PM
To: 'tru64-unix-managers_at_ornl.gov'
Subject: Is there a way of updating the hardware database ?


Tru64 UNIX 5.1a


When I have presented a disk to the system I didn't assign an IDENT number
to the device.

Therefore under "hwmgr -v d " I get ...........


root_at_avon:/home/bboddy >hwmgr -v d
 HWID: Device Name Mfg Model Location
 
----------------------------------------------------------------------------
--
    6: /dev/dmapi/dmapi                               
    7: /dev/scp_scsi                                  
    8: /dev/kevm                                      
   57: /dev/disk/floppy0c            3.5in floppy     fdi0-unit-0
   62: /dev/disk/dsk0c      COMPAQ   BD009122BA       bus-0-targ-0-lun-0
   63: /dev/disk/dsk1c      COMPAQ   BD009122C6       bus-0-targ-1-lun-0
   64: /dev/disk/dsk2c      COMPAQ   BD009122C6       bus-0-targ-2-lun-0
   65: /dev/disk/dsk3c      DEC      HSG80            bus-1-targ-1-lun-0
   68: /dev/disk/dsk6c      DEC      HSG80            bus-1-targ-1-lun-100
I now want to assign an IDENT number for this device, so that it would look
something like .............
root_at_avon:/home/bboddy >hwmgr -v d
 HWID: Device Name          Mfg      Model            Location
 
----------------------------------------------------------------------------
--
    6: /dev/dmapi/dmapi                               
    7: /dev/scp_scsi                                  
    8: /dev/kevm                                      
   57: /dev/disk/floppy0c            3.5in floppy     fdi0-unit-0
   62: /dev/disk/dsk0c      COMPAQ   BD009122BA       bus-0-targ-0-lun-0
   63: /dev/disk/dsk1c      COMPAQ   BD009122C6       bus-0-targ-1-lun-0
   64: /dev/disk/dsk2c      COMPAQ   BD009122C6       bus-0-targ-2-lun-0
   65: /dev/disk/dsk3c      DEC      HSG80            bus-1-targ-1-lun-0
   68: /dev/disk/dsk6c      DEC      HSG80            IDENTIFIER=123
The only way I can thing of to do this would be to delete the HWID with
dsfmgr and recreate it again. However to do this I would have to unmount any
file systems attached which I can't do.
Is there anyway I can do this dynamically ? 
Regards
Bill 
**********************************************************************
The information contained in this communication is
confidential, is intended only for the use of the recipient
named above, and may be legally privileged.
If the reader of this message is not the intended
recipient, you are hereby notified that any dissemination, 
distribution, or copying of this communication is strictly
prohibited.
If you have received this communication in error,
please re-send this communication to the sender and
delete the original message or any copy of it from your
computer system. Thank You.
Received on Tue Feb 11 2003 - 17:30:48 NZDT

This archive was generated by hypermail 2.4.0 : Wed Nov 08 2023 - 11:53:44 NZDT