Hello Friends:
Problem resolved. The cause was the graphics card adapter (the system
doesn't have keyboard and mouse port), then removing the graphics card
adapter i can install the operating system TRU64 Unix V5.1A.
Thanks very much to Dr. Tomas Blinn, who was give me the exactly solution.
The answer from Tom is below:
The return address (RA) is in the routine hal_get_sysinfo
[hal_get_sysinfo:1307, 0xffffffff006136fc] beq r0,
0xffffffff00613720
and the instrucion right before that is this:
[hal_get_sysinfo:1306, 0xffffffff006136f8] jsr r26, (r3),
hal_get_sysinfo+0x6d0
although the PC makes no particular sense..
In any case, that routine is involved with retrieving a variety of
system information.
The SPECIFIC case invoked here is in the routine for GSI_KEYBOARD
and it looks like it relates to a routine called ws_keyboard_name_proc
which presumably is supposed to retrieve a keyboard name string.
I'm wondering what's wrong with your hardware. Did you report you
were running an older version before and are trying to do a fresh
install? If so, did you update the firmware? There are things that
older firmware did not support that the new system software might
be dependent on. This is just a wild guess, but sometimes I get
lucky..
Or do you have some non-standard keyboard connected to the system?
I don't recall that GS140 systems have graphics, but clearly this
code is related to keyboard support. And it's failing badly. So
I suspect you might have a bizarre keyboard connected, or else it
is something else of that nature.
Regards.
John Cajas
----- Original Message -----
From: "John Cajas (TECSINFO)" <jcajas_at_andinanet.net>
To: <tru64-unix-managers_at_ornl.gov>
Sent: Monday, May 19, 2003 10:03 PM
Subject: Can't install tru64 Unix 5.1 on GS140
>
>
> Hello Friends:
>
> After that I did the suggestion from Dr. Thomas Blinn, Martin Ronde
> Anderson
> and Albert Ken, about the console variable bootdef_dev: set bootdef_dev
""
> The console variable os_type is set to unix
> The system continue dumping with the following messages:
>
> Initializing System for TRU64 Unix Installation
> Asigning a cluster device number to root
> Unable to save existing hardware configuration. New configuration will be
> used.
>
> Performing cdrom installation
>
> Loading installation process and scanning system hardware
>
> Trap: invalid memory read access from kernel mode
> faulting virtual address: 0x000000000000000010
> PC : 0xFFFFFFFF004e4d4c
> RA : 0xFFFFFFFF006136fc
> SP : 0xFFFFFFe0639017210
>
> panic (CPU0): Kernel memory fault
> dump
> CPU 0 halted
> halt code=5
> HALT instruction executed
>
>
>
> Any help is welcome.
>
> Regards.
>
> John Cajas
>
> > ----- Original Message -----
> > From: "John Cajas (TECSINFO)" <jcajas_at_andinanet.net>
> > To: <tru64-unix-managers_at_ornl.gov>
> > Sent: Sunday, May 18, 2003 8:05 PM
> > Subject: Can't install tru64 Unix 5.1 on GS140
> >
> >
> > > Hello Admins:
> > >
> > > GS140 6/525 with firmware 6.4, 12 CPU's, 8GB RAM, KFTHA on slot 8. I
> can't
> > > install tru64 UNIX V 5.1 on it, when i tried to boot from cdrom with
> > > operating system some errors appears:
> > >
> > > Boot adapter: KZPAA rev2 in bus slot 9 off of kftha0 in TLSB slot 8
> > >
> > > Attempting to mount previous root file system disk to save hardware
> > > configuration information...
> > > FAILED
> > >
> > > Unable to retain old hardware configuration from SCSI 0 4 0 00 ef00
> > >
> > > Trap: invalid memory read access from kernel mode
> > > faulting virtual address: 0x00000000000010
> > > ....
> > > ...
> > > ...
> > > panic (CPU 0): kernel memory fault
> > >
> > > .......
> > >
> > >
> > >
> > > Part of the output of show config command is:
> > > Name Type Ext Rev Nnemonic
> > > TLSB
> > > 0++ KN7CG-AB
> > > 1 KN7CG-AB
> > > 2 KN7CG-AB
> > > 3 KN7CG-AB
> > > 4 KN7CG-AB
> > > 5 KN7CG-AB
> > > 6 MS7CC
> > > 7 MS7CC
> > > 8 KFTHA 2000 0 0D03 kftha0
> > >
> > > C0 PCI Connected to kftha0
> > > 0+ VGA
> > > 4+ Qlogic ISP1040B isp0
> > > 6+ KGPSA-C kgppsa0
> > > 9+ KZPAA kzpaa0
> > > A+ DE500-BA tulip0
> > >
> > > There isn't port for keyboard and mouse, then i am installing the OS
> from
> > > serial console.
> > > isp0 has connected to 2 disks of 36.4 GB (ds-rz1fc-vw).
> > > KGPSA-C, is terminated (no connection to anything)
> > > KZPAA has the cdrom
> > >
> > >
> > > OpenVMS V 7.3-1 is installed in 1 disk (ds-rz1fc-vw), and the server
can
> > > boot from this operating system.
> > >
> > > Thanks in advance for any help or suggestion.
> > >
> > > Regards.
> > >
> > > John Cajas
> > >
> >
>
Received on Thu May 22 2003 - 02:21:53 NZST