Thanks to all.
Reinstalling.
God, give me back my VMS.
At the end is the output from console.
Best regards, Bob
Solution from Dr. Thomas P. Blinn:
Won't work. In V4.0x it was relatively easy to "clone" a system disk
even onto a quite different system type. On V5.x, there is a way to
use one system to load the software, but once it's configured it's
pretty strongly tied to the specific system on which it was booted.
And the methods for installing the software and then moving the disk
to a different system are NOT well documented (if they're documented
at all).
Do a clean install on the DS20E. It's easier.
Tom
Dr. Thomas P. Blinn + Tru64 UNIX Software + Hewlett-Packard Company
Internet: tpb_at_zk3.dec.com, thomas.blinn_at_compaq.com, thomas.blinn_at_hp.com
110 Spit Brook Road, MS ZKO3-2/W17 Nashua, New Hampshire 03062-2698
Alpha Hardware Platforms and I/O Phone: (603) 884-0646
ACM Member: tpblinn_at_acm.org PC_at_Home: tom_at_felines.mv.net
-------
From petergergen_at_kpmg.com.au:
Hi Bob
boot with genvmunix to get access to all the device drivers and then
recompile the kernel.
Regards
Peter
-------
From stan.robinson_at_mci.com:
in general you can't port from one architecture to another, ie, only from
DS20 to DS20,etc. someone may have a quickie way & i'm curious myself:)
goodluck
-------
Original question:
Installed fresh 5.1B on my home PW500au, all patches,
additional sw. Now i'm trying to move this disk to the DS20E.
Expected that this will work:
boot dkxx -fi /genvmunix -fl s
then rebuild kernel.
But it doesn't.
It says something about wrong architecture, then crash.
Is there a way to solve this?
Some kernel parameters?
TIA, Bob
-------
This is what i got from the console:
P00>>>b dka0 -fi /genvmunix -fl s
Resetting I/O buses...
(boot dka0.0.0.7.1 -file /genvmunix -flags s)
block 0 of dka0.0.0.7.1 is a valid boot block
reading 19 blocks from dka0.0.0.7.1
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 2600(9728)
initializing HWRPB at 2000
initializing page table at 3ff48000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
UNIX boot - Wednesday October 16, 2002
Loading /genvmunix ...
Loading at 0xffffffff00000000
Sizes:
text = 8447808
data = 2107248
bss = 2433664
Starting at 0xffffffff000123d0
bcm: DEGXA driver V1.0.14 NUMA lanlog
failed configuring ev7_ocla subsystem
DUMP: A dump found in memory will tie up 3940352 bytes until released.
Memory trolling not supported, cpu Major id 8, Minor id 7
Alpha boot: available memory from 0x2cf4000 to 0x3ff46000
Compaq Tru64 UNIX P5.1B (Rev. 306); Mon Apr 14 20:52:04 EDT 2003
physical memory = 1024.00 megabytes.
available memory = 978.32 megabytes.
using 3865 buffers containing 30.19 megabytes of memory
panic (cpu 0): kn600-pci_confl1: cannot configure PCI subsystem --
get_bus failure
DUMP: Warning: no disk available for dump.
DUMP: first crash dump failed: attempting memory dump...
DUMP: compressing 76072KB into 929951KB memory...
DUMP: Starting Address Ending Address Size(MB)
DUMP: ------------------ ------------------ --------
DUMP: 0xfffffc003fb46000 - 0xfffffc003ff45fef 4.0 (indicator)
DUMP: Writing data... [3MB]
DUMP: crash dump complete.
halted CPU 0
halt code = 5
HALT instruction executed
PC = ffffffff0035f3b0
P00>>>
--
Bob Marcan mailto:bob.marcan_at_snt.si
Aster^H^H...HermesPlus^H^H^H...S&T mailto:bob.marcan_at_aster.si
Nade Ovcakove 1 tel: +386 (1) 5894-329
1000 Ljubljana, Slovenia http://www.snt.si
Received on Mon Jun 23 2003 - 11:46:55 NZST