Don't if there is anyone out there still listening, but
I have tried bood 4.0 D,E,F,G OpenVMS7.3-2 without any
success. Last time this system was up in ran Linux.
COMPAQ Professional Workstation XP1000
Console V5.9-1 Dec 14 2000 16:19:05
OpenVMS PALcode V1.88-27, Digital UNIX PALcode V1.83-22
With E got as far as:
Alpha boot: available memory from 0x2ef8000 to 0x7ffec000
Digital UNIX V4.0G (Rev. 1530); Sun May 14 06:24:24 EDT 2000
physical memory = 2048.00 megabytes.
available memory = 2001.74 megabytes.
using 2618 buffers containing 20.45 megabytes of memory
emx: dynamic addressing enabled
Firmware revision: 5.9-1
PALcode: UNIX version 1.83-22
COMPAQ Professional Workstation XP1000
pci1 at nexus
tu0: DECchip 21143: Revision: 4.1
tu0: auto negotiation capable device
tu0 at pci1 slot 3
tu0: DEC TULIP (10/100) Ethernet Interface, hardware address: 00-00-F8-71-73-A9
tu0: auto negotiation on: will advertise 100BaseTX (UTP) port: full duplex
isp0 at pci1 slot 6
isp0: QLOGIC ISP1040C
isp0: Firmware revision 5.57 (loaded by console)
scsi0 at isp0 slot 0
rz0 at scsi0 target 0 lun 0 (LID=0) (IBM DNES-309170Y SA60) (Wide16)
rz1 at scsi0 target 1 lun 0 (LID=1) (COMPAQ BD0186459A B010) (Wide16)
pci2001 at pci1 slot 8
trio0 at pci2001 slot 10
trio0: S3 Trio64 (SVGA) Plug-N-Play, 0.5 Mb
gpc0 at isa0
pci0 at nexus
isa0 at pci0
gpc1 not probed
ace0 at isa0bed
lp0 at isa0
fdi0 at isa0
fd0 at fdi0 unit 0
ata0 at pci0 slot 107 (slot 7, function 1)
ata0: CYPRESS 82C693
cam_logger: CAM_ERROR packet
cam_logger: bus 1 target 1 lun 0
ataintr
Interrupt not expected
cam_logger: CAM_ERROR packet
cam_logger: bus 1 target 1 lun 0
ss_perform_timeout
timeout on request on the bus, scheduled bus reset
Active CCB at time of error
DDR - Warning: Device has no "name" - for
Vendor ID : Product ID: Revision:
and with G
Digital UNIX V4.0G (Rev. 1530); Sun May 14 06:24:24 EDT 2000
physical memory = 2048.00 megabytes.
available memory = 2001.74 megabytes.
using 2618 buffers containing 20.45 megabytes of memory
emx: dynamic addressing enabled
Firmware revision: 5.9-1
PALcode: UNIX version 1.83-22
COMPAQ Professional Workstation XP1000
pci1 at nexus
tu0: DECchip 21143: Revision: 4.1
tu0: auto negotiation capable device
tu0 at pci1 slot 3
tu0: DEC TULIP (10/100) Ethernet Interface, hardware address: 00-00-F8-71-73-A9
tu0: auto negotiation on: will advertise 100BaseTX (UTP) port: full duplex
isp0 at pci1 slot 6
isp0: QLOGIC ISP1040C
isp0: Firmware revision 5.57 (loaded by console)
scsi0 at isp0 slot 0
rz0 at scsi0 target 0 lun 0 (LID=0) (IBM DNES-309170Y SA60) (Wide16)
rz1 at scsi0 target 1 lun 0 (LID=1) (COMPAQ BD0186459A B010) (Wide16)
pci2001 at pci1 slot 8
trio0 at pci2001 slot 10
kernel inst fault=opdec, ps=0x0, pc=0xffffffff004868c8, inst=0x823de
panic (cpu 0): trap: illegal instruction
DUMP: No primary swap, no explicit dumpdev.
Nowhere to put header, giving up.
halted CPU 0
Next I tried booting off a disk, which has 5.1A on it
Loading vmunix symbol table ... [1607088 bytes]
Alpha boot: available memory from 0x36c2000 to 0x7ffec000
Compaq Tru64 UNIX V5.1A (Rev. 1885); Mon May 6 18:00:07 PDT 2002
physical memory = 2048.00 megabytes.
available memory = 1993.16 megabytes.
using 7814 buffers containing 61.04 megabytes of memory
Firmware revision: 5.9-1
PALcode: UNIX version 1.83-22
COMPAQ Professional Workstation XP1000
pci1 (primary bus:1) at nexus
pci2 (primary bus:1 subordinate bus:2) at pci1 slot 8
pci0 (primary bus:0) at nexus
isa0 at pci0
gpc0 at isa0
gpc1 not probed
ace0 at isa0
ace1 at isa0
lp0 at isa0
fdi0 at isa0
fd0 at fdi0 unit 0
ata1 at pci0 slot 107 (slot 7, function 1)
ata1: Cscsi0 at ata1 slot 0 rad 0
ata2 at pci0 slot 207 (slot 7, function 2)
ata2: CYPRESS 82C693
scsi1 at ata2 slot 0 rad 0
kernel console: ace0
dli: configured
NetRAIN configured.
panic (cpu 0): init_rootdev: boot device translation failed
DUMP: Warning: no disk available for dump.
DUMP: first crash dump failed: attempting memory dump...
DUMP: compressing 138328KB into 1903143KB memory...
DUMP: Starting Address Ending Address Size(MB)
DUMP: ------------------ ------------------ --------
DUMP: 0xfffffc007fb08000 - 0xfffffc007ffebfef 4.8 (indicator)
DUMP: Writing data...... [6MB]
DUMP: crash dump complete.
halted CPU 0
I then tried booting OpenVMS 7.3-2
>>>set boot_osflags 0,0
>>>boot dqa0
(boot dqa0.0.0.107.0 -flags 0,0)
block 0 of dqa0.0.0.107.0 is a valid boot block
reading 1134 blocks from dqa0.0.0.107.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 8dc00
initializing HWRPB at 2000
initializing page table at 7ffee000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
OpenVMS (TM) Alpha Operating System, Version V7.3-2
© Copyright 1976-2003 Hewlett-Packard Development Company, L.P.
%EXECINIT-F-LOADERR, error loading SYS$IPC_SERVICES.EXE, status = 00000044
halted CPU 0
Hints appreciated
Tom
Received on Wed Jul 30 2008 - 02:40:05 NZST