|
HP OpenVMS Systems Documentation |
|
OpenVMS System Messages: Companion Guide for Help Message Users
JBCMIXUP, fatal job controller interaction problem Facility: LOGIN, Login Procedure Explanation: An internal error occurred in the job controller during the login; the login cannot be performed. User Action: Repeat the login procedure. If the failure persists, notify the system operator or manager. JNLACP, Fatal error detected by journal ACP Facility: BUGCHECK, System Bugcheck Explanation: The OpenVMS software detected an irrecoverable, inconsistent condition. After all physical memory is written to a system dump file, the system automatically reboots if the BUGREBOOT system parameter is set to 1. User Action: Use the BACKUP command with the /IGNORE=NOBACKUP qualifier to make a backup save set of the system dump file and the error log file active at the time of the error. Contact a Compaq support representative and describe the conditions leading to the error. JNLDRV, Fatal error detected by journal driver Facility: BUGCHECK, System Bugcheck Explanation: The OpenVMS software detected an irrecoverable, inconsistent condition. After all physical memory is written to a system dump file, the system automatically reboots if the BUGREBOOT system parameter is set to 1. User Action: Use the BACKUP command with the /IGNORE=NOBACKUP qualifier to make a backup save set of the system dump file and the error log file active at the time of the error. Contact a Compaq support representative and describe the conditions leading to the error. JOURNAL, journaling to 'file-spec' Facility: BACKUP, Backup Utility Explanation: The Backup utility is writing journal records to the specified file in response to the /JOURNAL qualifier. This message is displayed only if the /LOG qualifier is specified. User Action: None. KRNLSTAKNV, kernel stack not valid Facility: BUGCHECK, System Bugcheck Explanation: The OpenVMS software detected an irrecoverable, inconsistent condition. After all physical memory is written to a system dump file, the system automatically reboots if the BUGREBOOT system parameter is set to 1. User Action: Use the BACKUP command with the /IGNORE=NOBACKUP qualifier to make a backup save set of the system dump file and the error log file active at the time of the error. Contact a Compaq support representative and describe the conditions leading to the error. LABELERR, error in tape label processing on 'save-set-spec' Facility: BACKUP, Backup Utility Explanation: The Backup utility encountered an error during an attempt to process the file labels on the specified volume. User Action: Take action based on the accompanying message. LARGECNT, 'device-name' is too large to be processed Facility: BACKUP, Backup Utility Explanation: The specified volume is too large to be processed by the Backup utility. Possibly the specified cluster factor is too small. User Action: Retry the operation using a larger volume cluster factor. LBLOVRWRITE, volume label 'label' overwritten, new label is 'label' Facility: BACKUP, Backup Utility Explanation: The loaded volume was overwritten and a new label was written to the volume. The labels specified in this message provide additional information. User Action: None. LINE_TRUNCATED, more than 'number' characters in line, at line 'line-number'. Facility: READ_CONFIG, File-Based Autoconfiguration Explanation: The command line exceeds the maximum allowable number of characters. The device description will not be added. User Action: Correct the command so that it contains 256 or fewer characters, and retry the operation. LISINPSAV, /LIST requires save set as input Facility: BACKUP, Backup Utility Explanation: The input specification for a listing operation must reference a save set. User Action: Correct the specification and reenter the command. LKBGRANTED, LKB is granted, but shouldn't be Facility: BUGCHECK, System Bugcheck Explanation: The OpenVMS software detected an irrecoverable, inconsistent condition. After all physical memory is written to a system dump file, the system automatically reboots if the BUGREBOOT system parameter is set to 1. User Action: Use the BACKUP command with the /IGNORE=NOBACKUP qualifier to make a backup save set of the system dump file and the error log file active at the time of the error. Contact a Compaq support representative and describe the conditions leading to the error. LKBREFNEG, LKB reference count negative Facility: BUGCHECK, System Bugcheck Explanation: The OpenVMS software detected an irrecoverable, inconsistent condition. After all physical memory is written to a system dump file, the system automatically reboots if the BUGREBOOT system parameter is set to 1. User Action: Use the BACKUP command with the /IGNORE=NOBACKUP qualifier to make a backup save set of the system dump file and the error log file active at the time of the error. Contact a Compaq support representative and describe the conditions leading to the error. LOADERR, error configuring device 'device-name', driver 'driver-name' Facility: IOGEN Explanation: An error occurred during autoconfiguration. User Action: Take action based on the accompanying message. LOCKERR, failed to lock volume Facility: RBLD, REBUILD Command (Mount Utility) Explanation: An error occurred while trying to lock the volume set against modification. User Action: Take action based on the accompanying message. LOCKMGRERR, error detected by Lock Manager Facility: BUGCHECK, System Bugcheck Explanation: The OpenVMS software detected an irrecoverable, inconsistent condition. After all physical memory is written to a system dump file, the system automatically reboots if the BUGREBOOT system parameter is set to 1. User Action: Use the BACKUP command with the /IGNORE=NOBACKUP qualifier to make a backup save set of the system dump file and the error log file active at the time of the error. Contact a Compaq support representative and describe the conditions leading to the error. LOGDISABL, logins are currently disabled - try again later Facility: LOGIN, Login Procedure Explanation: Logins are currently disabled. User Action: Do not attempt to log in at this time. Try again later. LOGNAME, logical name is too long Facility: MOUNT, Mount Utility Explanation: A logical name contains more than 255 characters. User Action: Correct and reenter the command.
Low Priority Command Queue Insert Failure
|