hi,
I've been having trouble getting 4.0G installed on a pair of DS20Es. The
systems came with 5.1 FIS and ran happily, but the customer insisted on having
4.0G. When booting up from the cd on both machines the scenario is the same and
looks like this:
Alpha boot: available memory from 0x1e46000 to 0x3ff56000
Digital UNIX V4.0G (Rev. 1530); Sun May 14 06:24:24 EDT 2000
physical memory = 1024.00 megabytes.
available memory = 993.85 megabytes.
using 1307 buffers containing 10.21 megabytes of memory
emx: dynamic addressing enabled
Firmware revision: 5.8-10
PALcode: UNIX version 1.79-63
COMPAQ AlphaServer DS20E 666 MHz
pci1 at nexus
isp0 at pci1 slot 7
isp0: QLOGIC ISP1040B/V2 - Differential Mode
isp0: Firmware revision 5.57 (loaded by console)
isp0: Fast RAM timing enabled.
scsi0 at isp0 slot 0
rz0 at scsi0 target 0 lun 0 (LID=0) (DEC HSZ70 V73Z) (Wide16)
rzb0 at scsi0 target 0 lun 1 (LID=1) (DEC HSZ70 V73Z) (Wide16)
rzc0 at scsi0 target 0 lun 2 (LID=2) (DEC HSZ70 V73Z) (Wide16)
rzd0 at scsi0 target 0 lun 3 (LID=3) (DEC HSZ70 V73Z) (Wide16)
rze0 at scsi0 target 0 lun 4 (LID=4) (DEC HSZ70 V73Z) (Wide16)
rzf0 at scsi0 target 0 lun 5 (LID=5) (DEC HSZ70 V73Z) (Wide16)
rzg0 at scsi0 target 0 lun 6 (LID=6) (DEC HSZ70 V73Z) (Wide16)
rzh0 at scsi0 target 0 lun 7 (LID=7) (DEC HSZ70 V73Z) (Wide16)
rz1 at scsi0 target 1 lun 0 (LID=8) (DEC HSZ70 V73Z) (Wide16)
rzb1 at scsi0 target 1 lun 1 (LID=9) (DEC HSZ70 V73Z) (Wide16)
rzc1 at scsi0 target 1 lun 2 (LID=10) (DEC HSZ70 V73Z) (Wide16)
rzd1 at scsi0 target 1 lun 3 (LID=11) (DEC HSZ70 V73Z) (Wide16)
itpsa0 at pci1 slot 8
IntraServer ROM Version V2.0 (c)1998
scsi1 at itpsa0 slot 0
rz8 at scsi1 target 0 lun 0 (LID=16) (COMPAQ BD009635CB BDC4) (Wide16)
ee0 at pci1 slot 9
ee0: COMPAQ Intel 82559 (10/100 Mbps) Ethernet Interface
ee0: Driver Rev = V1.0.5, Chip Rev = 8, hardware address: 00-50-8B-AE-D0-5E
gpc0 at isa0
pci0 at nexus
isa0 at pci0
gpc1 not probed
ace0 at isa0bed
lp0 at isa0
fdi0 at isa0
fd0 at fdi0 unit 0
ata0 at pci0 slot 105 (slot 5, function 1)
ata0: CYPRESS 82C693
scsi2 at ata0 slot 0
rz16 at scsi2 target 0 lun 0 (LID=17) (COMPAQ CD-224E 9.5B)
ata1 at pci0 slot 205 (slot 5, function 2)
ata1: CYPRESS 82C693
scsi3 at ata1 slot 0
usb0 at pci0 slot 305 (slot 5, function 3)
Adaptec 7895 Adapter: H/W Rev 4, Driver 4/3/00 Rev 2.199 CHIM v261a1
aha_chim0 at pci0 slot 6
scsi4 at aha_chim0 slot 0
Adaptec 7895 Adapter: H/W Rev 4, Driver 4/3/00 Rev 2.199 CHIM v261a1
kernel inst fault=gentrap, ps=0x4, pc=0xffffffff0021c0a8, inst=0xaa
panic (cpu 0): trap: illegal instruction
DUMP: No primary swap, no explicit dumpdev.
Nowhere to put header, giving up.
CP - SAVE_TERM routine to be called
CP - SAVE_TERM exited with hlt_req = 1, r0 = 00000000.00000000
halted CPU 0
halt code = 5
HALT instruction executed
PC = ffffffff002263d0
It always happens after discovering the second adaptec controller. AFAIK all
firmware revisions are correct (seeing as it runs 5.1 okay I guess that's the
case). Does anyone have any idea as how to get past this point?
cheers
john
Received on Tue Nov 28 2000 - 14:42:29 NZDT