Hi all,
I am trying to create one mirrored and one mirrored&striped LSM volume on a
new system (DS20, Tru64 v5.0a, rootdg already configured). I am not so
familiar with LSM, so I probably did something wrong...I created a mirrored
volume (without DRL) and started it without any problems. However, when I
created mirrored&striped volume and tried to start it I got the following
error message:
lsm:volume: ERROR: Volume data01vol has no complete, non-volatile ACTIVE
plexes
Here is what I did:
- Labelled and initialized disks - here is the output of the "voldisk list"
command:
# voldisk list
DEVICE TYPE DISK GROUP STATUS
dsk0a nopriv root01 rootdg online
dsk0b nopriv swap01 rootdg online
dsk0d simple dsk0d rootdg online
dsk0f nopriv var01 rootdg online
dsk0g nopriv usr01 rootdg online
dsk0h simple tmp01 rootdg online
dsk1 sliced - - online
dsk2 sliced - - online
dsk3 sliced - - online
dsk4 sliced - - online
dsk5 sliced - - online
dsk6 sliced - - online
dsk7a nopriv root02 rootdg online
dsk7b nopriv swap02 rootdg online
dsk7d simple dsk7d rootdg online
dsk7f nopriv var02 rootdg online
dsk7g nopriv usr02 rootdg online
dsk7h simple tmp02 rootdg online
dsk8 sliced - - online
dsk9 sliced - - online
dsk10 sliced - - online
dsk11 sliced - - online
dsk12 sliced - - online
dsk13 sliced - - online
- Created a new disk group data_dg and added all disks (except for dsk0 and
dsk7) to this disk group - here is the output of the "volprint -g data_dg
-dt" command:
DM NAME DEVICE TYPE PRIVLEN PUBLEN STATE
dm dsk1 dsk1 sliced 4096 71127888 -
dm dsk2 dsk2 sliced 4096 71127888 -
dm dsk3 dsk3 sliced 4096 71127888 -
dm dsk4 dsk4 sliced 4096 71127888 -
dm dsk5 dsk5 sliced 4096 71127888 -
dm dsk6 dsk6 sliced 4096 71127888 -
dm dsk8 dsk8 sliced 4096 71127888 -
dm dsk9 dsk9 sliced 4096 71127888 -
dm dsk10 dsk10 sliced 4096 71127888 -
dm dsk11 dsk11 sliced 4096 71127888 -
dm dsk12 dsk12 sliced 4096 71127888 -
dm dsk13 dsk13 sliced 4096 71127888 -
- Here is the hardware topology (output of the "/dev/rdisk/dsk*c command):
dsk0c: character special (19/22) SCSI #0 "BD018635C4" disk #0 (SCSI ID #0)
(SCSI LUN #0)
dsk1c: character special (19/38) SCSI #0 "BD03664553" disk #1 (SCSI ID #1)
(SCSI LUN #0)
dsk2c: character special (19/54) SCSI #0 "BD03664553" disk #2 (SCSI ID #2)
(SCSI LUN #0)
dsk3c: character special (19/70) SCSI #0 "BD03664553" disk #3 (SCSI ID #3)
(SCSI LUN #0)
dsk4c: character special (19/86) SCSI #0 "BD03664553" disk #4 (SCSI ID #4)
(SCSI LUN #0)
dsk5c: character special (19/102) SCSI #0 "BD03664553" disk #5 (SCSI ID #5)
(SCSI LUN #0)
dsk6c: character special (19/118) SCSI #0 "BD03664553" disk #6 (SCSI ID #8)
(SCSI LUN #0)
dsk7c: character special (19/150) SCSI #3 "BD018635C4" disk #0 (SCSI ID #0)
(SCSI LUN #0)
dsk8c: character special (19/166) SCSI #3 "BD03664553" disk #1 (SCSI ID #1)
(SCSI LUN #0)
dsk9c: character special (19/182) SCSI #3 "BD03664553" disk #2 (SCSI ID #2)
(SCSI LUN #0)
dsk10c: character special (19/198) SCSI #3 "BD03664553" disk #3 (SCSI ID #3)
(SCSI LUN #0)
dsk11c: character special (19/214) SCSI #3 "BD03664553" disk #4 (SCSI ID #4)
(SCSI LUN #0)
dsk12c: character special (19/230) SCSI #3 "BD03664553" disk #5 (SCSI ID #5)
(SCSI LUN #0)
dsk13c: character special (19/246) SCSI #3 "BD03664553" disk #6 (SCSI ID #8)
(SCSI LUN #0)
- Created mirrored volume data02vol using disks dsk6 and dsk13 (no DRL):
# volmake -g data_dg sd dsk6-01 dsk6,0,71127888
# volmake -g data_dg sd dsk13-01 dsk13,0,71127888
# volmake -g data_dg plex data02-01 sd=dsk6-01
# volmake -g data_dg plex data02-02 sd=dsk13-01
# volmake -g data_dg -Ufsgen vol data02vol plex=data02-01,data02-02
# volume start data02vol (no problems to start it!)
- Created mirrored and striped volume data01vol (first tried without DRL):
# volmake -g data_dg sd dsk1-01 dsk1,0,71127888
# volmake -g data_dg sd dsk2-01 dsk2,0,71127888
# volmake -g data_dg sd dsk3-01 dsk3,0,71127888
# volmake -g data_dg sd dsk4-01 dsk4,0,71127888
# volmake -g data_dg sd dsk5-01 dsk5,0,71127888
# volmake -g data_dg sd dsk8-01 dsk8,0,71127888
# volmake -g data_dg sd dsk9-01 dsk9,0,71127888
# volmake -g data_dg sd dsk10-01 dsk10,0,71127888
# volmake -g data_dg sd dsk11-01 dsk11,0,71127888
# volmake -g data_dg sd dsk12-01 dsk12,0,71127888
# volmake -g data_dg plex data01-01 layout=stripe st_width=64k \
sd=dsk1-01,dsk2-01,dsk3-01,dsk4-01,dsk5-01
# volmake -g data_dg plex data01-02 layout=stripe st_width=64k \
sd=dsk8-01,dsk9-01,dsk10-01,dsk11-01,dsk12-01
# volmake -g data_dg -Ufsgen vol data01vol plex=data01-01,data01-02
# volprint -ht data01vol
Disk group: data_dg
V NAME USETYPE KSTATE STATE LENGTH READPOL PREFPLEX
PL NAME VOLUME KSTATE STATE LENGTH LAYOUT NCOL/WID
MODE
SD NAME PLEX DISK DISKOFFS LENGTH [COL/]OFF DEVICE
MODE
v data01vol fsgen DISABLED EMPTY 355639632 ROUND -
pl data01-01 data01vol DISABLED EMPTY 355639632 STRIPE 5/128
RW
sd dsk1-01 data01-01 dsk1 0 71127888 0/0 dsk1
ENA
sd dsk2-01 data01-01 dsk2 0 71127888 1/0 dsk2
ENA
sd dsk3-01 data01-01 dsk3 0 71127888 2/0 dsk3
ENA
sd dsk4-01 data01-01 dsk4 0 71127888 3/0 dsk4
ENA
sd dsk5-01 data01-01 dsk5 0 71127888 4/0 dsk5
ENA
pl data01-02 data01vol DISABLED EMPTY 355639632 STRIPE 5/128
RW
sd dsk8-01 data01-02 dsk8 0 71127888 0/0 dsk8
ENA
sd dsk9-01 data01-02 dsk9 0 71127888 1/0 dsk9
ENA
sd dsk10-01 data01-02 dsk10 0 71127888 2/0 dsk10
ENA
sd dsk11-01 data01-02 dsk11 0 71127888 3/0 dsk11
ENA
sd dsk12-01 data01-02 dsk12 0 71127888 4/0 dsk12
ENA
- Tried to start the volume:
# volume start data01vol
lsm:volume: ERROR: Volume data01vol has no complete, non-volatile ACTIVE
plexes
- Removed the volume (using "voledit -r -rm data01vol") and tried to create
it with DRL, like this:
# volprint -ht data01vol
Disk group: data_dg
V NAME USETYPE KSTATE STATE LENGTH READPOL PREFPLEX
PL NAME VOLUME KSTATE STATE LENGTH LAYOUT NCOL/WID
MODE
SD NAME PLEX DISK DISKOFFS LENGTH [COL/]OFF DEVICE
MODE
v data01vol fsgen DISABLED EMPTY 284511696 ROUND -
pl data01-01 data01vol DISABLED EMPTY 284511696 STRIPE 4/128
RW
sd dsk1-01 data01-01 dsk1 0 71127888 0/0 dsk1
ENA
sd dsk2-01 data01-01 dsk2 0 71127888 1/0 dsk2
ENA
sd dsk3-01 data01-01 dsk3 0 71127888 2/0 dsk3
ENA
sd dsk4-01 data01-01 dsk4 0 71127888 3/0 dsk4
ENA
pl data01-02 data01vol DISABLED EMPTY 284511696 STRIPE 4/128
RW
sd dsk8-01 data01-02 dsk8 0 71127888 0/0 dsk8
ENA
sd dsk9-01 data01-02 dsk9 0 71127888 1/0 dsk9
ENA
sd dsk10-01 data01-02 dsk10 0 71127888 2/0 dsk10
ENA
sd dsk11-01 data01-02 dsk11 0 71127888 3/0 dsk11
ENA
pl data01-03 data01vol DISABLED EMPTY LOGONLY CONCAT -
RW
sd dsk5-01 data01-03 dsk5 0 71127888 LOG dsk5
- Tried to start the volume, but received the same error message again:
# volume start data01vol
lsm:volume: ERROR: Volume data01vol has no complete, non-volatile ACTIVE
plexes
Unfortunatelly this error message is not listed in the "LSM error messages"
section of the LSM manual.
Any ideas? I would really appreciate your help.
Thanks in advance,
Zoran
Received on Sun Nov 04 2001 - 20:52:14 NZDT