Hello Friends:
After that I did the suggestion from Dr. Thomas Blinn, Martin Ronde
Anderson
and Albert Ken, about the console variable bootdef_dev: set bootdef_dev ""
The console variable os_type is set to unix
The system continue dumping with the following messages:
Initializing System for TRU64 Unix Installation
Asigning a cluster device number to root
Unable to save existing hardware configuration. New configuration will be
used.
Performing cdrom installation
Loading installation process and scanning system hardware
Trap: invalid memory read access from kernel mode
faulting virtual address: 0x000000000000000010
PC : 0xFFFFFFFF004e4d4c
RA : 0xFFFFFFFF006136fc
SP : 0xFFFFFFe0639017210
panic (CPU0): Kernel memory fault
dump
CPU 0 halted
halt code=5
HALT instruction executed
Any help is welcome.
Regards.
John Cajas
> ----- Original Message -----
> From: "John Cajas (TECSINFO)" <jcajas_at_andinanet.net>
> To: <tru64-unix-managers_at_ornl.gov>
> Sent: Sunday, May 18, 2003 8:05 PM
> Subject: Can't install tru64 Unix 5.1 on GS140
>
>
> > Hello Admins:
> >
> > GS140 6/525 with firmware 6.4, 12 CPU's, 8GB RAM, KFTHA on slot 8. I
can't
> > install tru64 UNIX V 5.1 on it, when i tried to boot from cdrom with
> > operating system some errors appears:
> >
> > Boot adapter: KZPAA rev2 in bus slot 9 off of kftha0 in TLSB slot 8
> >
> > Attempting to mount previous root file system disk to save hardware
> > configuration information...
> > FAILED
> >
> > Unable to retain old hardware configuration from SCSI 0 4 0 00 ef00
> >
> > Trap: invalid memory read access from kernel mode
> > faulting virtual address: 0x00000000000010
> > ....
> > ...
> > ...
> > panic (CPU 0): kernel memory fault
> >
> > .......
> >
> >
> >
> > Part of the output of show config command is:
> > Name Type Ext Rev Nnemonic
> > TLSB
> > 0++ KN7CG-AB
> > 1 KN7CG-AB
> > 2 KN7CG-AB
> > 3 KN7CG-AB
> > 4 KN7CG-AB
> > 5 KN7CG-AB
> > 6 MS7CC
> > 7 MS7CC
> > 8 KFTHA 2000 0 0D03 kftha0
> >
> > C0 PCI Connected to kftha0
> > 0+ VGA
> > 4+ Qlogic ISP1040B isp0
> > 6+ KGPSA-C kgppsa0
> > 9+ KZPAA kzpaa0
> > A+ DE500-BA tulip0
> >
> > There isn't port for keyboard and mouse, then i am installing the OS
from
> > serial console.
> > isp0 has connected to 2 disks of 36.4 GB (ds-rz1fc-vw).
> > KGPSA-C, is terminated (no connection to anything)
> > KZPAA has the cdrom
> >
> >
> > OpenVMS V 7.3-1 is installed in 1 disk (ds-rz1fc-vw), and the server can
> > boot from this operating system.
> >
> > Thanks in advance for any help or suggestion.
> >
> > Regards.
> >
> > John Cajas
> >
>
Received on Tue May 20 2003 - 03:04:17 NZST