I've got a DS20 running v4.0F that is being updated with a new CPU, RAID
and tru64 v5.0A. The new CPU and RAID hardware installs went fine. Now
when I try to boot from the v5.0A installation CD it hangs. I let it sit
for about 30 minutes without any progress. The machine boots 4.0F fine.
The v6.0 firmware update CD booted fine. I can mount and read from the
v5.0A CD. The CD has been used to boot other DS20Es. Below I include the
info from the 4.0F boot marking where it hangs during the 5.0A CD boot.
Any suggestions?
Thanks Anton
----------------------------------------
Alpha boot: available memory from 0xd82000 to 0xff5a000
Digital UNIX V4.0F (Rev. 1229); Sat Feb 23 14:13:34 EST 2002
physical memory = 256.00 megabytes.
available memory = 241.85 megabytes.
using 972 buffers containing 7.59 megabytes of memory
Firmware revision: 6.0-8
PALcode: Digital UNIX version 1.87-69
AlphaServer DS20 833 MHz
pci1 at nexus
isp0 at pci1 slot 7
isp0: QLOGIC ISP1040B/V2
isp0: Firmware revision 5.57 (loaded by console)
isp0: Fast RAM timing enabled
********* v5.0A CD boot hangs here *********
scsi0 at isp0 slot 0
tz4 at scsi0 target 4 lun 0 (LID=0) (DEC TLZ09 (C) DEC 03a5)
tz5 at scsi0 target 5 lun 0 (LID=1) (DEC TZ89 (C) DEC 2150) (Wide16)
isp1 at pci1 slot 9
isp1: QLOGIC ISP1040B/V2 - Differential Mode
isp1: Firmware revision 5.57 (loaded by console)
isp1: Fast RAM timing enabled.
scsi1 at isp1 slot 0
rz9 at scsi1 target 1 lun 0 (LID=2) (SEAGATE ST15150W 0022) (Wide16)
rz11 at scsi1 target 3 lun 0 (LID=3) (SEAGATE ST15150W 0023) (Wide16)
rz12 at scsi1 target 4 lun 0 (LID=4) (SEAGATE ST15230W 0638) (Wide16)
rz14 at scsi1 target 6 lun 0 (LID=5) (SEAGATE ST15150W 0022) (Wide16)
gpc0 at isa0
pci0 at nexus
isa0 at pci0
gpc1 not probed
gpc1 not probed
ace0 at isa0
ace1 at isa0
lp0 at isa0
fdi0 at isa0
fd0 at fdi0 unit 0
ata0 at pci0 slot 105 (slot 5, function 1)
ata0: CYPRESS 82C693
scsi2 at ata0 slot 0
ata1 at pci0 slot 205 (slot 5, function 2)
ata1: CYPRESS 82C693
scsi3 at ata1 slot 0
usb0 at pci0 slot 305 (slot 5, function 3)
comet0: Card type 'Elsa GLoria' with 8MB framebuffer memory.
comet0 at pci0 slot 7
itpsa0 at pci0 slot 8
IntraServer ROM Version V2.0 (c)1998
scsi4 at itpsa0 slot 0
rz37 at scsi4 target 5 lun 0 (LID=6) (SEAGATE ST318404LW 0006) (Wide16)
itpsa1 at pci0 slot 108 (slot 8, function 1)
IntraServer ROM Version V2.0 (c)1998
scsi5 at itpsa1 slot 0
pci2000 at pci0 slot 9
itpsa2 at pci2000 slot 0
IntraServer ROM Version V2.0 (c)1998
scsi6 at itpsa2 slot 0
rz53 at scsi6 target 5 lun 0 (LID=7) (DEC RRD47 (C) DEC 1206)
itpsa3 at pci2000 slot 1
IntraServer ROM Version V2.0 (c)1998
scsi7 at itpsa3 slot 0
rz56 at scsi7 target 0 lun 0 (LID=8) (DEC RZ2DD-LS (C) DEC 0306) (Wide16)
tu0: DECchip 21140: Revision: 2.2
tu0: auto negotiation capable device
tu0 at pci2000 slot 2
tu0: DEC TULIP (10/100) Ethernet Interface, hardware address: 00-06-2B-00-AE-67
tu0: auto negotiation off: selecting 10BaseT (UTP) port: half duplex
Created FRU table binary error log packet
lvm0: configured.
lvm1: configured.
kernel console: comet0
dli: configured
i2c: Server Management Hardware Present
ADVFS: using 2316 buffers containing 18.09 megabytes of memory
Environmental Monitoring Subsystem Configured.
Received on Sun Feb 24 2002 - 15:21:19 NZDT